LLOYD S LC-1355 Heater User Guide

LLOYD S LC-1355 Heater

Product Information

• Product Name: Calefactor
• Brand: Lloyd’s
• Model: LC-1355

Take control from one single app and transform your spaces into safe, efficient, comfortable, and fun places.

Quick Guide
Please read the installation guide before operating the product. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference caused by the undesired operation. This appliance is not for persons (including children) whose physical, sensory, or mental capacities are different, reduced, lack experience or knowledge. Supervise children to ensure that this device is not used as a toy.

Safety warnings

This product is for indoor use only.
Keep this instructive for future reference. For questions or clarifi-cations, contact our technicians at the telephone number at the end of this manual. If the power cable becomes damaged, stop using the appliance immediately and take it to an authorized repair center for examination, adjustment, or replacement. Never attempt to repair the cable or any part of the appliance, and never allow unauthorized persons to do so.

1. Use the heater on flat surfaces without slopes.
2. There is a risk of fire or explosion if installing the appliance near a curtain or any combustible material. The heater must operate at a minimum distance of 20 inches from any wall or object.
3. Please observe the following instructions:
   • Verify that the power supply meets the electrical requirements of the heater.
   • Never share the power outlet with other high-wattage electrical appliances.
   • Do not connect the heater to an extension cord or battery backup (No Break).
   • Verify the correct connection of the plug to the outlet and that both are in good condition to prevent overheating and malfunction.
   • To disconnect the heater, grasp the plug and unplug it from the outlet. Never pull on the power cord.
   • To avoid skin burns, do not touch the metal part of the heater when it is in operation.
4. Do not use the heater near hot surfaces.
5. Ensure that the device is placed firmly on its base at all times. Do not move the heater while in operation. Check that the air inlet and outlet openings are not blocked.
6. Do not insert any objects through the heater grille.
7. Never place the heater on soft surfaces such as a bed or where the openings could become blocked.
8. The heater is not for environments containing dust or volatile materials (they may obstruct the grilles), in humid places, near flammable products, or out-doors.
9. Do not place the heater immediately under a receptacle or outlet.
10. Do not use the heater near a bathtub, shower, or swimming pool.
11. Before disconnecting the heater, please turn it off and allow it to cool for 30 to 60 seconds to protect internal parts.
12. Never insert fingers or any objects through the grille, as this may cause injury, electric shock, or damage to the appliance.
13. Never place objects or mats on top of the power cord.
14. This heater is a device that emits and receives radio waves.
15. Ensure that the heater does not come into contact with water or other liquids. If the appliance accidentally gets wet or immersed in liquid, turn the heater off at the power switch, and disconnect the plug from the outlet. Carefully dry both plug and outlet before reconnecting.
16. Unplug the appliance from the outlet when not in use.
17. After removing the packaging, check that the device is intact. Packaging compo-nents (plastic bags, unicell, sponges, etc.) should not be left close to children as they are potentially dangerous.
18. Ensure that the airflow is unobstructed to optimize the heating performance. Avoid installing it in corners or small spaces.
19. Do not hang the appliance or place it next to a wall.

WARNING: To avoid any risk of fire or overheating, do not cover the heater with any object.

Overheating protection
In the event of overheating, the heater will automatically shut down. When this ha-ppens, unplug it for about 30 minutes until it cools down completely, and check that no objects obstruct the grilles that may cause the overheating. Then turn it back on and verify that it works properly. If not, turn it off again and consult a qualified tech-nician. For safety, the heater will automatically stop operating when it is tilted or in motion.

Cleaning and maintenance

1. Clean the exterior surfaces of the heater regularly with a damp cloth. Never rinse or immerse directly in water. Be sure to unplug the device before cleaning.
2. Do not use flammable or abrasive substances to clean the device.
3. Never disassemble the heater when a malfunction occurs. In this case, consult a qualified technician.
4. If the heater is unused for long periods, unplug it and store it in a dry place away from dust and sunlight.

Characteristics

• Device remotely controllable from anywhere through the app
• Turn off, turn on, and set the room temperature from 15 °C to 35 °C (59 °F to 95 °F) from the app, manually and by voice commands
• Control panel and LCD to consult and change the temperature manually
• 45° oscillation
• Timer from 1 to 12 hours
• On/Off scheduling from the app
• It has three temperature levels:
  • High (28 °C/82.4 °F)
  • Medium (26 °C/78.8 °F)
  • Low – fan mode (15 °C/59 °F)
• 16 AWG ( 1.31 mm2) 1.5-meter power cable
• Ceramic heating system
• Overheating protection
• Removable dust particle filter
• Roll-over switch protection
• For indoor use
• Multi-user
• No HUB required
• Compatible with Google Assistant and/or Amazon Alexa
• Compatible with Siri Shortcuts through routines created from the app
• Allows you to create routines that trigger actions in other Lloyd’s Smart products

Installation

1. Carefully remove the heater from its box and plastic bag.
2. Place the heater on a firm, level surface.
3. Verify that the red main power switch on the back is off. Plug the power cable into a 120 V~ 60 Hz electrical outlet. Once plugged in, change the switch position to on.

Control panel

This heater has a control panel and an LCD to facilitate the manual operation of all its functions.

• ON/OFF BUTTON:
  Press this button once, and the heater will start to operate. Press it again, and the heater will turn off within 30 seconds.

• POWER LEVEL BUTTON (POWER):
  When the heater starts to operate, the air temperature it emits will be 15°C (59 °F), the air emission icon will light up, and its power consumption will be less than 750W. Press this button to increase the air temperature.

  • a. If you press the power button once, the heater will turn on at medium power (750 W), and the temperature of the air emitted will be 26 °C (79 °F). The “medium power” icon will light up.
  • b. If you press the power button a second time, the heater will turn on high power (1500 W), and the temperature of the air emitted will be 28 °C (82 °F).
  • c. If you press the power button a third time, the power will return to below 750W.

• TIMER:
  This button will help you set a shutdown timer for the heater from 1 to 12 hours.

• SWING BUTTON:
  Press this button, and the heater will start oscillating at a 45° angle. Press it again, and it will stop oscillating.

• RAISE AND LOWER TEMPERATURE BUTTONS:
  Allow you to manually increase the temperature of the air emitted from 15 °C to 35 °C (59 °F to 95 °F).

Before getting started

• Make sure your smartphone has iOS 10.0 or higher or Android™ 4.4 or higher. Check your network and make sure you are connected to a 2.4 GHz Wi Fi channel.
• Download the Lloyds Smart app from the App Sto-re or on Google Play or scan the following QR code with your smartphone.

Registration and access

• Launch the Lloyds Smart app, to continue, click “Agree.” Click on “Sign Up” (1), choose your country and enter an email address, then click “Get Verification Code” (2).
• Enter the code sent to your email (check inbox or spam) (3), set a password, and click “Done” (4). Or log in directly if you already have an account.

Add device

• Start the Lloyds Smart app, and select “+” in the upper right corner (1). Choose the type of device you want to add. In this case, go to ” “Comfort” (2), then click on “Smart heater” (3). Enter your Wi Fi network information and password, then click “Next” (4).

• Connect the heater to the power supply. Press the “POWER” button for 5 seconds until the Wi Fi LED indicator flashes rapidly. Confirm in the app (5) and click “Next” (6).

• Once the device is configured, you can change the name (7). Finally, click on “Done” (8).
  NOTE: Make sure that the Wi Fi password that you enter is correct and that the device is close to the modem during the process.

• After completing the setup, find and select the device in the list (9) to control it through the app from wherever you are. Only an internet connection is required.

Device control
In “More functions” (interface upper right corner), you will be able to rename the device, share control of it with family and acquaintances, access information, up-date the firmware or delete the device.
Note: The name that you assign to the device will be the one that you use with your Alexa or Google Assistant-enabled device for voice control.

How to configure with Siri Shortcuts

Lloyd’s Smart products are compatible with Siri Shortcuts through routines created from the app. For configuration details, scan the following QR code with your smartphone:

• Make sure your smartphone has iOS 12 or higher.

Google Assistant and Amazon Alexa

• How to connect to Google Assistant:

1. Download and launch the Google Home app, previously configured with your Gmail account and your Google Assistant-enabled device.
2. Click on the “+” icon, choose “Set up Device,” then in the “Works with Google” sec tion, click on the search bar and type in Lloyds Smart. When you get the icon, click on it. Enter your Lloyds Smart account and click on “Link now”. Then press on “Authorize” and wait a few seconds.
3. Once you have linked Lloyds Smart, the devices added to your account will be displa yed, click on “X” (top left corner) and return to the main screen. Now you can control your Lloyd’s Smart devices using just your voice with Google.  

Note: You can rename the devices from the Lloyds Smart app to control them with voice commands. Every time you rename the devices, say: “Hey Google, sync devices” or update from the Google Home app.
Try saying “Hey Google” followed by one of the following commands:

  * Hey Google, turn on heater”
  * “Hey Google, turn off heater”
  * “Hey Google, set heater to 25 degrees*”  

*The heater will set the temperature in degrees Celsius. “Google, Android, Google Play and Google Home are trademarks of Google LLC.”

• How to connect to Amazon Alexa

1. Download and access the “Amazon Alexa” app, previously configured with your email account and your virtual assistant.
2. Click on the option “Skills & games”, then in the search bar type Lloyds Smart. When you get the icon, click on it. Then press the “Activate to use” button.
3. Enter your Lloyds Smart account, click on “Link Now” and finally “Authorize”. You will get the message “Linked successfully”, click on “Close” and wait a few seconds.
4. Click “Detect devices” to find the smart devices. Now you can ask your assistant to control them by voice commands.  

Note: You can rename the devices from the Lloyds Smart app to control them with voi-ce commands. Every time you rename the devices, say: “Alexa, sync devices” or update from the Amazon Alexa app.

5.  **Voice command examples:  

**

  * “Alexa, turn on heater”
  * “Alexa, turn off heater”
  * “Alexa, set heater to 30 degrees*”

Technical specifications

• 120 V~ 60 Hz 1 500 W
• POWER CONSUMPTION IN WORKING MODE 120 V~: 1 408 W
• POWER CONSUMPTION IN STAND BY MODE 120 V~: N/A

IMPORTED BY: ZUTTO TECHNOLOGIES, S.A. DE C.V. AVENIDA EJÉRCITO NACIONAL No. 505 INTERIOR 1602, COL. GRANADA, MIGUEL HIDALGO
CIUDAD DE MÉXICO, MÉXICO. C.P. 11520
R.F.C.: ZTE161017KT6
Phone: 55 68447575
lloydscorp.com

References

• Lloyd’s ® – Productos de automatización y seguridad para su hogar

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>