AENO AGS0001 GS1 Garment Steamer User Manual
- June 9, 2024
- AENO
Table of Contents
AENO AGS0001 GS1 Garment Steamer User Manual
The AENO GS1 garment steamer is designed to remove creases and wrinkles in fabric, improve the appearance of different types of fabric using a powerful steam jet.
Specifications
Voltage: AC 220–240 V; Frequency: 50/60 Hz. Power: 1500.0 W. Dimensions
(length × width × height): 201 mm × 128 mm × 293 mm. Water tank volume: 0.25
l. Steam modes: 35 g/min (high), 30 g/min (medium), 15±3 g/min (low).
Steam temperature: up to +160 °C.
Package Contents
(Fig. A)
AENO GS1 steamer (1), brush head (4), measuring cup (5), quick start guide, warranty card.
Limitations and Warnings
WARNING! The device connected to the mains is live even after it has been
turned off by the power button (6); unplug it immediately after use, before
cleaning, filling and emptying the water tank (2).
Do not allow the body of the steamer or the power cord to come in contact with
water. Do not leave the device plugged in unsupervised. Do not allow children
to use or play with the device. Do not turn on a damaged device. Use the
device indoors only. Unplug the device by holding the power plug, not the
cord; do not use an extension cord. The working surface of the steamer head
gets hot during operation, do not touch hot surfaces. Do not point the nozzle
at people. Never steam clothes on a person. Check the care label before
steaming. Use only distilled water.
Before the first use
Unpack the device. Place it on a stable horizontal surface without plugging it in. Fill the water tank as shown in figure C. It is recommended to use the measuring cup (5) provided for filling the device.
Operating the device
Connect the device to the mains by inserting the power plug into the power
outlet. Press the power button (6): the blue light (7) will light up, the red
light (8) will blink. Wait about 35 seconds for the steam to build up. Quiet
crackling during heating is allowed. The device is ready for operation when
the red indicator (8) is lit steadily. Place the item to be steamed vertically
or horizontally. Select the steam mode using the “+/-” button (9). Point the
steamer head away from yourself and those present, release the first batch of
steam, point the steamer head at the surface to be steamed. Start steaming by
pressing steam button (10). Press the steam button (10) again to stop
steaming.
Press the power button (6) to turn the device off. Drain the remaining water
from the water tank.
Steam modes (adjustable with the “+/-” button (9)):
- low (one indicator light (8) of steam mode is on) – delicate fabrics/light wrinkles;
- medium (two indicators (8) of steam mode are on) – everyday clothes made of cotton, polyester/medium creases;
- high (three indicators (8) of steam mode are on) – heavy fabrics/strong wrinkles.
WARNING! When using the device for the first time, check the operation of the device on old clothing: it is possible that dust accumulated in the device during production and transportation.
Note: For better steaming, it is recommended to use the brush head (4). Install the brush head only on the unit when it is turned off and cool.
Auto Power Off Mode
If there is no operation in 15minutes,the power supply is automatically turned off.
Troubleshooting
- The steamer is not heated. Possible causes: the device is not turned on or not connected to the power supply. Solution: Make sure that the unit is turned on, the power plug is connected to the socket outlet, and the socket outlet is in proper condition.
- The steamer does not produce steam. Possible causes: low water level in the water tank; the water tank is installed incorrectly; device is not turned on or not plugged in. Solution: unplug the device and fill the water tank; install the water tank as shown in Figure C; make sure the steamer is turned on and plugged in, and the socket outlet is in good condition.
- Water drips from the steamer head or leaks out of the tank. Possible causes: the steamer is not heated to the desired temperature; the water tank cap (3) is not properly closed. Solution: wait (about 35 seconds) for the red indicator light (8) to light steadily; install the water tank as shown in figure C.
WARNING! If none of the possible solutions solves your problem, contact your supplier or service center. Do not disassemble or attempt to repair the device yourself.
Recycling information
These symbols indicate that you must follow the Waste Electrical and
Electronic Equipment (WEEE) and Waste Battery and Battery
Regulations when disposing of the device, its batteries and accumulators, and
its electrical and electronic accessories.
According to the rules, this equipment must be disposed of separately at the
end of its service life. Do not dispose of the device, its batteries and
accumulators, or its electrical and electronic accessories together with
unsorted municipal waste, as this will harm the environment. To dispose of
this equipment, it must be returned to the point of sale or turned in to a
local recycling facility. You should contact your local household waste
disposal service for details.
ASBISc reserves the right to modify the device and to make edits and changes
to this document without prior notice to users.
The warranty period and service life shall be 2 years as from the date of
purchase of the device.
Manufacturer: ASBISc Enterprises PLC, Lapetou, 1, Agios Athanasios, 4101
Limassol, Cyprus. Made in China. For current information and details on the
device description and specification, as well as connection process,
certificates, warranty, and quality issues, see relevant Installation and
Operation Manuals available for downloading at
aeno.com/documents. All trademarks and names
herein are the property of their respective owners.
References
- Home appliances AENO - Smart home appliances on the official website of the manufacturer AENO in Europe
- Documents | AENO in Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>