SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation Guide

June 3, 2024
SLOAN

SLOAN SS-3055 Wall Hung Ledgeback Lavatory

SLOAN SS-3055 Wall Hung Ledgeback Lavatory

THE RIGHT CHOICE

We thank you for your purchase. Our products are 100% tested but should you have any questions, please contact us by phone or at our web site.

WARNING: Any vitreous china can chip or break if the bolts or nuts are over-tightened or if mishandled.

BEFORE YOU START…

  • Check all local plumbing and building codes.
  • Check for any damage to the new lavatory sink before installation.

WHAT YOU WILL NEED…

  • Putty knife
  • 10” adjustable wrench
  • Safety glasses
  • Phillips screwdriver
  • Measuring tape
  • Flathead screwdriver
  • Basin wrench
  • Drill
  • Tube cutter
  • Plumbers putty
  • Hacksaw
  • Silicone sealant
  • Channel lock pliers

DIMENSIONS

SLOAN SS-3055 Wall Hung Ledgeback Lavatory Dimensions

SLOAN SS-3055 Wall Hung Ledgeback Lavatory Dimensions

RETROFIT INSTALLATIONS

REMOVE EXISTING LAVATORY
  • Turn off the water supply.
  • Disconnect the supply lines and waste pipes.
  • Remove the existing lavatory.
  • Scrape any old putty or sealant from wall surface.
  • Remove old wall bracket and discard.
  • Adequate structural support in or behind the wall is required to withstand the weight of the lavatory when lled with water.
CLEAN DRAIN
  • Clean out waste pipe using hand or power cleaner to be sure pipe is clear.
  • Proceed to NEW INSTALLATIONS.

NEW INSTALLATIONS

PRIOR TO NEW INSTALLATION
  • Determine appropriate wall location for the lavatory. Consider that hot and cold water supply lines with supply stops or a tempered water supply line with supply stop and a drain line will be required. A 120V electrical source (receptacle) may also be required. Compare the physical dimensions of the lavatory to the space available for the installation.
UNPACK AND INSPECT LAVATORY
  • Carefully remove sink from its protective carton so as not to damage porcelain nish. Check for anydamage to lavatory before proceeding with the installation.
  • Examine the carton for additional parts before discarding packaging..
INSTALL DRAIN AND FAUCET
  • Install the faucet and drain assembly (not included).
    Follow faucet manufacturers instructions. Use plumbers putty to ensure a water seal.
    SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation
illustration
INSTALL NEW WALL HANGER BRACKET
  • Determine the desired height to the top of lavatory sink rim. Mark level line on wall. This line is centerline of holes for wall hanger bracket mounting holes.
  • Mark and drill holes in wall for mounting lavatory
    SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation
illustration

Note: Adequate reinforced wall framing is required behind the wall for proper hanger bracket support.
Use of wall anchors or toggle bolts is not recommended. For concrete walls a properly sized wall anchor can be used.

  • Mount and level wall hanger bracket using six (6) screws and washers (not supplied)
    SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation
illustration

Note: Check if lavatory is level. If not level, remove lavatory and adjust wall bracket as needed.
Install two (2) 5/16” anchor bolts (not supplied), through the (2) 3/8” anchor holes, in the sink and into the wall.
CAUTION! Do not overtighten the bolts. Breakage and chipping of vitreous china can occur.
SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation
illustration

COMPLETING THE INSTALLATION
  • Connect all supply lines and waste pipes.
  • Turn on water. Check to see that the faucet and drain are operating properly and there are no leaks.
  • Caulk around lavatory perimeter where lavatory meets the wall.
  • Record lavatory model number for reference
    SLOAN SS-3055 Wall Hung Ledgeback Lavatory Installation
illustration
CARE AND CLEANING OF VITREOUS CHINA

Clean lavatory with a cleaner safe for vitreous china.
Spray and wipe clean using soft cloth. Soft abrasive cleaners may be used to remove stains.

LIMITED WARRANTY

Sloan Valve Company warrants its vitreous china products to be made of rst class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efcient manner when properly installed and serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER. NOTE: IN NO EVENT SHALL THE SLOAN VALVE COMPANY BE LIABLE FOR INCIDENTAL DAMAGES, RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE OR ALTERATION.

The information contained in this document is subject to change without notice.

Customer Support

SLOAN VALVE COMPANY
10500 Seymour Avenue
Franklin Park, IL 60131
Phone: 1-800-9-VALVE-9 (982-5839)
or 1-847-671-4300
Fax: 1-800-447-8329 or 1-847-671-4380
sloan.com
Copyright © 2019 Sloan Valve Company
Code No. 0816873 Rev. 1 (08/19)

SLOAN Logo

Documents / Resources

| SLOAN SS-3055 Wall Hung Ledgeback Lavatory [pdf] Installation Guide
SS-3055 Wall Hung Ledgeback Lavatory, SS-3055 Lavatory, SS-3055, Lavatory, Wall Hung Lavatory, Ledgeback Lavatory
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals