WASSERSTEIN Ultra 2 3-in-1 Wired Floodlight User Manual

Table of Contents

$WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $2$$

$WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $3$$

Disassembling the light head is not recommended as it may cause damage to internal components. The floodlight may not function aptly after disassembling it.
DO NOT remove the protective LED lens.
DO NOT look at LEDs that are on for any length of time

Installing the Floodlight to the wall plate

1. Install the wall plate on the wall using the 4 screws (included) and the 4 anchors (included).
Remove the protective tape from the EVA gasket and press the adhesive side firmly against the rear of the floodlight. $WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $5$$
Important: Before mounting the floodlight completely, apply the EVA gasket. It prevents water from seeping into the wall plate
Mount the floodlight + EVA gasket taped onto the wall plate.
Mount the floodlight onto the wall plate and secure it with the long screw provided $WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $6$$
Insert the appropriate plug into the adapter; turn clockwise until it clicks.
Remarks: 3 x plug heads are included (US, UK, EU).
Connect the floodlight cable and adaptor cable together, then screw in the plastic cover $WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $8$$
Plug the adapter onto the wall socket to power the floodlight $WASSERSTEIN- Ultra 2 3-in-1-Wired-Floodlight-fig- $9$$
Peel the adhesive skins then stick the cable clips onto the wall. Run the wires of the adapter through the cable clips for a better cable management. $WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $10$$

To charge your camera via the floodlight, firmly connect the Arlo Pro 3/Pro 4 & Arlo Ultra/Ultra 2 magnetic cable in the magnetic charging port.
Screw the camera onto the mount.
Open the USB port cap of the floodlight and connect the Arlo Pro 3/Pro 4 & Arlo Ultra/Ultra 2 magnetic cable. Press in firmly.
Adjust the camera to your preferred viewing angle

$WASSERSTEIN-Ultra 2 3-in-1-Wired-Floodlight-fig- $11$$

Important Tips

Assess where intruders are most likely to enter and the path they would take. Most intruders enter the home through a back door, patio door, or garage door. Therefore, it is advisable to place the ﬂoodlight near the entrances to your home.
Mount the ﬂoodlight on walls that an intruder would walk alongside, such as a narrow pathway. The motion sensor works best when movements are detected parallel to the ﬂoodlight, not towards it.
You can also mount the ﬂoodlight beside your security camera to illumi-nate the camera’s vision at night.
Although the ﬂoodlight is weatherproof, it is advisable to mount it to a wall shaded from the rain and sunlight to maximize battery life.

The ﬂoodlight keeps ﬂashing. What should I do?
Check your connection of all three wires to the house power.
Check the area around the ﬂoodlight as it may be detecting motion.
Will the ﬂoodlight turn on during the day?
No, the ﬂoodlight will only turn on during the night or when the surrounding light is dim.
Is a solar panel recommended, or will the hard-wired floodlight keep the camera charged?
It does not require a solar panel as the hard-wired floodlight’s USB port will keep the camera powered continuously
After installing the floodlight, how can I confirm that it is working?
Try waving your hands in front of the floodlight. If all of your connections are fine, the floodlight will light up due to the motion. If it does not light up, please check your wiring, especially if the cable colors match. Or, allow up to 10 minutes of reset time for the floodlight without triggering them.