HYUNDAI RC 606 AM/FM Stereo Radio with Stereo CD/MP3 Player Instruction Manual

HYUNDAI RC 606 AM/FM Stereo Radio with Stereo CD/MP3 Player

LOCATION OF CONTROL AND INDICATORS

FONT PANEL

1. AM Tuning Dial Scale.

2. FM Tuning Dial Scale.

3. Power ON/OFF- VOLUME Control.

4. CD Door Support Bracket.

5. CD Door.

6. CD Tray.

7. CD Control Buttons.

8. Speakers

9. CD Diskette Cover

10. TUNING Control

11. Function Buttons (AM/FM/CD/MP3)

12. FM ST or CD Indicator

13. PROGRAM Indicator

14. CD/MP3 Track Number Display

15. PLAY/PAUSE Indicator

16. Repeat Indicator

17. REPEAT/ALL Button

18. PROGRAM Button

19. B.SKIP Button

20. F.SKIP Button

21. PLAY/PAUSE Button

22. STOP Button
    BACK PANEL

23. FM Antenna

24. DC Input Jack

25. Headphone out

OPERATING INSTRUCTIONS

LISTENING TO THE RADIO

1. Power on the unit by turning the volume control knob clockwise position. The Tuning Dial light comes „on“
2. Press the function buttons (MW/FM) for the desired band, MW or FM.
3. Rotate the TUNNING control to tune to the desired radio station. If you tune to an FM Stereo station, the FM ST. Indicator will come „On“.
4. Adjust the VOLUME control as desired.
5. When you finish listening turn off the unit.

ANTENNA INFORMATION

AM – The MW bar antenna is inside the cabinet. If AM reception is unsatisfactory try repositioning the cabinet slightly until the internal antenna is picking up the strongest signal.
FM – The FM wire antenna is located on the back cabinet. If necessary adjust the position and direction of this antenna until you find the position that provides the best reception.

PLAYING COMPACT DISCS & MP3 DISCS

NOTE: Although this CD player can read CD-R,CD-RW and MP3 discs in addition to notmal CD, however, the playability of CD-R/RW & MP3 discs may be affected by the type of software that was used to create the discs, as well as the quality and condition of the blank media you are using. 100% playability cannot be quaranteed. This is not an indication of a problem with the player.

1. Power on the unit by turning the volume control knob clockwise position.
2. Press the function buttons (CD/MP3) for the CD function. The CD track number display comes „On“
3. Place your disc on the CD spindle with the printed label side facing up and lower th CD diskette cover.
4. The disc will spin for a few seconds while the player reads the disc at the read time, the discs will automatically playback, then the disc stops and the display shows the total number of tracks on the discs.
5. Press the PLAY/PAUSE button to begin playback from the first track. The Play indicator comes „On“. Note: You may leave the CD door open during playback if you wish, but we recommend closing the door again for better sound and also to prevent excess dust from accumulating on the CD.
6. Adjust the VOLUME control as desired.
7. Playback will continue until the end of disc. When the disc ends the display again shows the total number of tracks on the disc. You may also stop palyback at any time by pressing the STOP button.

PAUSE CONTROL
In play mode, press the PLAY/PAUSE button once. Pause playback but the disc continues to spin and the display flashes. Press the PLAY/PAUSE button once more to cancel pause and resume playback. The display stops flashing.

SKIPPING TRACKS AND HIGH SPEED MUSIC SEARCH
During CD/R-RW & MP3 Playback, repeatedly press the F. SKIP (Forward Skip) or B. SKIP (Back Skip) button to select the desired track or desired passage of the track. Repeatedly press TRACK+10 or TRACK-10 button on the remote control, it will help you to choose the desired track 10 number tracks one time.

REPEAT PLAYBACK
This feature allows you to continuously repeat a single track or the entire disc.

TO REPEAT A SINGLE TRACK
Press the REPEAT/ALL button once. The repeat indicator flashes. Press the B.SKIP or F.SKIP button to select the desired track, then press the PLAY/PAUSE button to begin repeat playback of the selected track.

TO REPEAT THE ENTIRE DISC
Press the REPEAT/ALL button twice. The repeat indicator remain „On“. Press the PLAY/PAUSE button to begin repeat playback of the entire disc. To cancel repeat playback press the REPEAT/ALL button until the repeat Indicator goes „Off“. Repeat palyback is also cancelled by pressing the STOP button or setting the function selector to the MW or FM position.

PROGRAMMED PLAYBACK

This feature allows you to program of the CD 20 tracks and MP3 99 tracks on a disc for playback in any desired order.
Note: You can program tracks while a disc is stopped or playing.

1. Press the PROGRAM button to enter the Program Mode. The Program number briefly shows „0 0 1“, the „0 0 1“ and the Program indicator flash.

2. Press the F.SKIP or B.SKIP button to select the first track number you wish to enter in the program memory. Example: Track Number „0 0 8“.

3. When the desired track number appears on the display, press the PROGRAM button again to memorize the track. The programnumber briefly shows „0 0 2“, then „0 0 2“ flashes.

4. Repeat steps 2-3, select a different track number each time until you have entered up to CD 20 tracks and MP3 99 tracks in the program memory.
   Note: You may program the same track number to play multiple times in the program sequence if desired.

5. Press the PLAY/PAUSE button to begin programmed playback. The PROGRAM indicator stop flashing and remains „On“. Playback will begin with the first track you have programmed track has been played.

6. After the last track has been played the player stops and the display shows the total number of tracks on the disc. However the program sequence remains in the memory.

7. The programmed sequence may be cancelled by press STOP button twice, switching to the MW, FM or shutting the system „Off“.

PROGRAM REPEAT PLAYBACK
You can use the program and repeat features together to continuously repeat a programmed sequence of tracks.

• First, program the desired tracks according to steps 1-5 on page 8-9. When programmed playback begins press the REPEAT/ALL button twice to activate all tracks repeat feature.
• The repeat indicator lights and all the tracks in your programmed sequence will be repeated continuosly.
• To cancele programmed repeat playback, press the REPAT/ALL button again to repeat indicators go „Off“.
  NOTE: All of buttons on the remote control have the same function as these buttons in the CD tary.

SPECIFICATION

• Frequency Range: AM 530 – 1600 kHz FM 87,5 – 108 MHz
• Power Source: DC 12 V 2A AC 100-240 V / 50 Hz
• Power Consumption: 19 W
• Power Consumption Off mode: 0 W
• Antennas: Built-in Ferrite Bar for AM External Antenna for FM
• Speaker: 4“ Dynamic type x 2
• Weight (NETTO): 4,3 kg

WE RESERVE THE RIGHT TO CHANGE TECHNICAL SPECIFICATIONS

WARNING: DO NOT USE THIS PRODUCT NEAR WATER, IN WET AREAS TO AVOID FIRE OR INJURY OF ELECTRIC CURRENT. ALWAYS TURN OFF THE PRODUCT WHEN YOU DON’T USE IT OR BEFORE A REVISION. THERE AREN’T ANY PARTS IN THIS APPLIANCE WHICH ARE REPARABLE BY CONSUMER. ALWAYS APPEAL TO A QUALIFIED AUTHORIZED SERVICE. THE PRODUCT IS UNDER A DANGEROUS TENTION.

TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Disposal of old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems).
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Hereby, ETA a.s. declares that the radio equipment type RC606 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.hyundai- electronics.cz/declaration_of_conformity

Charging adapter

A

| Manufacturer’s name or trademark, business registration number and address| “Shenzhen Cenwell Technology Co., Ltd., 2F, 3F, 301, Building C, Shengshun Industrial park, No. 142-4 Junxin Road, Niuhu Community, Guanlan Town, Longhua district, Shenzhen, China”
---|---|---
B| Model identifier| CW1202000EU
C| Input voltage| 100-240 V
D| Input frequency| 50/60 Hz
E| Output voltage| 12,0 V
F| Output current| 2,0 A
G| Output power| 24,0 W
H| Average efficiency in active mode| 87,78 %
I| Low load efficiency (10%)| 84,62 %
J| Power consumption without load| 0,065 W

References

• Hyundai Electronics– Hyundai CZ
• Hyundai electronics– Hyundai PL
• Hyundai Electronics– Hyundai SK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>