Warmup WSM-200 Snow Melting Cable Panel Instruction Manual
- June 3, 2024
- Warmup
Table of Contents
Warmup WSM-200 Snow Melting Cable Panel
Product Description
The WSM-200 panel is a versatile panel to switch loads from Snow Melting and
Roof De-icing applications.
It can be used by itself with the integrated timer module or connected to a
third-party sensor mounted outside.
- Enclosure : NEMA 1 for indoor mounting
- Relays :Four (4) 240V/60A Relays
- Amperage: MAX load bearing of 240A/240V single phase power.
- Approvals: UL-approved components assembled in UL 508A facility.
Product Specifications
The WSM-200 is intended to operate Warmup’s WSM and WSMM snow melting cables and mats in in-gound snow melting applications. The device must be mounted indoors. The WSM200 is currently designed to operate in-ground snow melting systems and is not yet calibrated to operate roof melting applications. While it can perform that function, it is not yet updated with the specific requirements of such applications (run-off melting, etc). The WSM-200 is specifically designed to work with the wattage output of cables manufactured by Warmup Inc / Warmup PLC. Warmup makes no guarantees as to its suitability when used with non-Warmup systems.
PANEL LAYOUT
- The WSM-200 controller has four (4) – 240VAC/60A contactor relays.
- One (1) contactor relay requires a 240VAC/60A dedicated inbound circuit (see Figure 1, #1 & 2). This contactor relay will supply power to the Ground Fault
- Relay, and the Manual Timer (see Figure 1, #3 & 4).
- There are three (3) additional contactor relays to accommodate larger loads. Each of the optional relays require a 240VAC/60A dedicated inbound circuit (see Figure 1, #6).
- There are eight (8) outbound GFPE 240VAC/30A breakers two (2) per contactor relay (see Figure 1, #5) supplying the heater(s).
- Required: 1 – 240VAC/60A Dedicated Inbound Circuit
- Required: Contactor Relay
- Ground Fault Relay
- Manual Timer
- GFPE Breakers (8): 240VAC/30A (each breaker)
- Optional Contactor Relays: 3 – 240VAC/60A
Manually Activating The WSM200
- You can activate your WSM-200 manually by pressing the on/off button on the door of the enclosure. This is accessible to the user from the outside of the panel.
- However, at initial set-up, the internal timer should be set up with the desired number of hours for the timer to function upon being triggered by the ON/OFF button.
- The timer can be set from 1 to 99 hours and Warmup defaults the timer at 1 period of 10 hours. We do not recommend less than 5 hours for proper snow melting results. This can be changed at any point by the user.
- When changing the settings of the timer, you must first disconnect power to the whole unit, then change settings, then turn power back on. This is not only for safety reasons, but also because the timer requires a power-cycle reset when its settings are changed.
- The manual operation of the system can serve as an override to the WiFi activation. This means that at any point, the user can activate the system manually without interrupting the regular operation of the system using the WiFi signal and the app’s parameters.
- The breaker must be turned off before adjusting the timer settings.
MANUAL TIMER SETTINGS
T1-K KLEMSAN TIMER SETTINGS
- Set the top orange dial to 10h
- Set the middle orange dial to the number of “run time” hours.
- a. 1 Hour = 0.1
- b. 2 Hours = 0.2
- c. 3 Hours – 0.3
- d. 4 Hours = 0.4
- e. 5 Hours = 0.5
- f. 6 Hours = 0.6
- g. 7 Hours = 0.7
- h. 8 Hours = 0.8
- i. 9 Hours = 0.9
- j. 10 Hours = 1.0
- Set the bottom orange dial to Mode “D”
80.1 FINDER TIMER SETTINGS
- Set the top gray dial to 24h
- Set the middle blue dial to the number of “run time” hours.
- Set the bottom white dial to “BE”mode
Example: Run Time = 5 Hours
- Set Top Dial to 24h
- Set Middle Dial to 5
Wiring Diagram
SUPPORT
Online
www.warmup.com Technical Helpline
888-927-6333
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>