BEOK BOT-T9N-WIFI Desktop Type RF Smart Thermostat for Wall-Hung Boiler User Manual
- June 3, 2024
- BEOK
Table of Contents
- BEOK BOT-T9N-WIFI Desktop Type RF Smart Thermostat for Wall-Hung Boiler
- Instruction
- Standard Acceaaories
- Product Overview
- Product Overview
- Display Symbols
- User routine operation
- Auto-mode Setting
- RF Thermostat advanced setting (Usually for Professional Techniclans)
- RF Receiver operating Instructions
- Dimensions (Unit: mm)
- lnstallation location
- RF thnermostat mounting steps
- RF Thermostat Installation step
- RF Thermostat installation steps
- RF Receiver wiring diagram
- Pairing steps
- Pairing steps
- Function Introduction (Wi-Fi only)
- Network Configuration (Wi-Fi only)
- Wi-Fi setting (VWi-Fi only)
- Voice control (Wi-Fi only)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BEOK BOT-T9N-WIFI Desktop Type RF Smart Thermostat for Wall-Hung Boiler
View all BEOK thermostat manual
Instruction
- The equipment function is stable and reliable, and the operation is simple and convenient
- The device has antifreeze function, child lock function and humidity function (only Wi-Fi model)
- Knob type control temperature setting is more convenient, flexible, and more experience
- Dual mode settings, operation can be set at will, comfortable Freedom and control of life
- RF transmitter desktop design, compatible with wall-mounted design, installation is very simple, flexible
- Relying on stable RF wireless technology, the thermostat is paired with the receiver, the signal is stable, and the pairing speed is fast
Standard Acceaaories
-
Product
-
USBwrie
-
Screw pack
-
Manual
Product Overview
This set is suitable for wall-hung boiler temperature control. As long as you install the receiver RC9 device near the wall-hung oiler, even if the thermostat T9N/T9W is placed in the living room or room (with an open distance of 100 meters), the RC9 can be controlled by the T9N/TOW thermostat.
Product Overview
Display Symbols
[ RF Thermostat l
[ RF Receiver l
User routine operation
Auto-mode Setting
Press ‘knob key for 3 seconds to edit auto-mode setting
RF Thermostat advanced setting (Usually for Professional Techniclans)
Under power-off, press “Knod key” for 3 seconds to enter advanced setting mode, then repress Knob key to switch to next mode. Press power button to save and exit advanced setting mode.
RF Receiver operating Instructions
Dimensions (Unit: mm)
lnstallation location
he installation distance between the thermostat and the receiver does not
exceed 100m (the distance can be judged according to the actual network
coverage)
Tip: There are many ways to install the RF thermostat,
- Owall mounting
- desktop placement
RF thnermostat mounting steps
-
Note: two power supply methods
- It is recommended to use brand new 1.5 V alkaline AA batterie
- Please ensure the correct polarity when installing the battery.
02×5 Alkalibatterien
- Insert a screwdriver into the notch on the back of the thermostat, pry open the base and panel frame, and then put the battery into the battery compartment of the device;
- After inserting the battery, close the back cover to complete the installation.
USB powered (Type C interface)
Use Type-C cable to power or the device
RF Thermostat Installation step
- Put the wire into the terminal and tighten it With a flat-blade screwdriver. After tightening the terminal screws, cover the upper cover to complete the installation.
RF Thermostat installation steps
-
Release front cover by inserting a head screw-driver into bottom crack.
-
The user can choose the wiring method by himself
- Exposed wiring: choose any one of the four directions, then use a flat-blade screwdriver to pry open along the dotted line;
- Concealed installation and routing: along the dotted line in the middle of the bottom shell, use a flat-blade screwdriver to pry open)
RF Receiver wiring diagram
The thermostat operates in full capacity in areas with the altitude of less than 2500 above sea level. Power rating of external load should be less than or equal to 80%rated power of thee thermostat in areas with altitude of 2500m to 4200m.
Pairing steps
- Under power-off, press ” ” for 3 seconds, when the green light flashes, the receiver enters the pairing state..
- Under power-off, press” power button +knob key” for 3 seconds, the thermostat enters the pairing state.
Pairing steps
- When the receiver’s buzzer beeps once, and the power light the green light always on, the pairing is successful are
Function Introduction (Wi-Fi only)
APP remote control and voice control
Network Configuration (Wi-Fi only)
Download Smart Life APP
Wi-Fi setting (VWi-Fi only)
-
On the OFF state, long press the “power button” for 3 seconds, when the screen flashes and ” ” , the thermostat Enter the state of distribution network;
-
Enter the Home” interface of the APP, click in the upper right comer, select the “Go to add ” button in the pop-up window, and finally click ” to enter the Wi-Fi password interface
Please turn on the Bluetooth of your phone in advance. -
Select 2.4G Wi-Fi and enter the password, click “Confirm “, and then wait for the connection to succeed;
-
After the addition is successful, click “phone, and the RF thermostat has been added successfully.’
Voice control (Wi-Fi only)
After waking up the speaker, you can say:
Amazon Alexa : Alexa, Turn on the HEATER
- *Turn off the HEATER.
- *Make the HEATER cooler in here.
- *Make the HEATER warmer in here.
- *What is the temperature of the HEATER?
- *Turn on child lock for the HEATER
- *Turn off child lock for the HEATER
Google Assistant: OK google
- *Turn on the HEATER Turn off the HEATER. Set the HEATER to 26 degree
-
- Drop the HEATER by 1 degree
- *Raise the HEATER by 1 degree Turn on child lock for the HEATER
-
- Turn off child lock for the HEATER
*Attention: ” HEATER is the device name, you can also name it yourself.
The temperature unit of thermostat and smart speaker must be identical.
Beok BOT-T9N-WIFI Smart Thermostat User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>