SW-MOTECH BC.SYS.01.548.20000 SysBag 30 Bag System Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.SYS.01.548.20000 SysBag 30 Bag System
MOUNTING INSTRUCTIONS
QUICK-LOCK EVO Side Carrier
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
»www.sw-motech.com
Installation and/or maintenance of this product require good technical
understanding. For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop. SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance
work.
Carefully follow all the directions given in the mounting instructions.
Also pay attention to all relevant information in the vehicle manual during
assembly. Nonconformance can lead to vehicle damage or even endanger the
driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change driving behavior
and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration or operation as well as TUV regulations where applicable. If required, register installed parts in the vehicle documents together with the appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all parts are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Make sure to use only the appropriate tools.
During installation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer specifications or
replaced by parts and hardware delivered by SW-MOTECH. Secure all threads,
unless otherwise specified, with medium-strong strength liquid thread locker.
If not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and
nuts must be tightened according to DIN/ISO specifications. After installation
make sure that all parts and hardware previously removed are properly
replaced.
FUNCTION CHECK: After installation also make sure that no moving parts
are obstructed and function of the vehicle is not hindered in any way. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions. Regularly check [every 1 DO km) for the
proper seating of all parts and connections removed during installation.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Maximum load per side carrier: 1 D kg / 22 lbs (including side case/luggage and Adapter Kitl! The maximum vehicle load specified by the manufacturer must not be exceeded!
Maximum speed with mounted side cases/luggage: 130 km/h!
The side carriers are designed exclusively for the use of SW-MOTECH Adapter Kits.
Dismount the side carriers when travelling without side cases/luggage. Always use the side carriers in pairs.
ATTENTION: Make sure that after attaching the luggage to the vehicle it is not in the exhaust flow! Dangers of burns!
PARTS LIST
Step
| No.| Item No. / Description| Part| **Quantity ***|
N-m
---|---|---|---|---|---
|
1
| KFT.01.519.002| Mounting Bracket [left side)| 1 / 1|
2
| M6 x 50; DIN 912| Hexagon Socket Screw| 2/2| 9,6
3
| d 6,4; DIN 125| Washer| 2 / 4|
4
| 14 / 6,2 / 11| Spacer| 2/2|
5
| 14 / 6,2 / 7| Spacer| 2/2|
|
6
| KFT.00.064.001| Mounting Bracket [right side)| 1 / 1|
|
7
| MB x 55; DIN 912| Hexagon Socket Screw| 1 / 1| 23
8
| d 8,4; DIN 9021| Washer| 1 / 1|
9
| MB; DIN 6927| Lock Nut with Flange| 1 / 1|
|
10
| KFT.01 .548.961.01| Side Carrier (left side)| 1 / 1|
|
11
| KFT.01 .548.962.01| Side Carrier [right side)| 1 / 1|
|
12
| KFT.01 .548.001 L_002L| Mounting Stud [left side)| 1 / 1|
13
| KFT.01 .548.001 R_002R| Mounting Stud [right side)| 1 / 1|
14
| M6 x 40; ISO 7380| Lenshead Screw; black| 8 /8| 9,6
15
| M6; DIN 6927| Lock Nut with Flange; black| 8 / ID|
|
16
| KFT.11.422.003| Crossbar| 1 / 1|
17
| M6 x 20; DIN 912| Hexagon Socket Screw| 2 /2| 9,6
18
| d 6,4; DIN 125| Washer| 2 / 4|
19
| d 6,4; DIN 9021| Washer| 2 /2|
20
| M6; DIN 6927| Lock Nut with Flange; black| 2 / ID|
|
21
| SV.ST.078.100.LK.02| QUICK-LOCK Fastener| 4 /4|
22
| CAM.2312S10-1 BP| QUICK-LOCK Fastener| 4 /4|
MOUNTING
Remove the original screws and spacers from the spring preload adjuster.
Attach the mounting bracket [1) with the spring preload adjuster to the
passenger footrest mount, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Do not fully tighten the screws yet.
Remove the original parts from the exhaust mount.
Attach the mounting bracket [6) with the original washer [Orig.) to the
exhaust mount, as shown in the drawing.
Do not fully tighten the screw yet.
Attach the mounting studs (12) and (13) to the side carrier (10).
Tighten the screws as specified in the parts list.
Attach the mounting studs ( 12) and ( 13) to the side carrier ( 11).
Tighten the screws as specified in the parts list.
Hang the side carriers I10I and 111] into the holding openings of the vehicle
provided on both sides.
Connect the side carriers 11 DI and 111] to the mounting brackets and the
crossbar I16I with the fasteners 121].
Connect both side carries 110] and 111] to the mounting brackets 11], and 16]
by using the fasteners 121], as shown in the detail drawing. Now connect the
crossbar 116] to the side carriers by using the fasteners 121].
Mark with a appropriate pencil the mounting holes of the crossbar 116] on the
license plate mount. Then loosen the fasteners 121] and remove the crossbar
116].
Use a 6.5-mm drill to drill the mountings holes for the crossbar 116]. Deburr
the edges of the mounting holes.
Hang the side carriers [10) and [11) into the holding openings of the vehicle
provided on both sides.
Connect the side carriers [10) and [11) to the mounting brackets and the
crossbar with the fasteners [21). Secure the the fasteners [21) with the lock
washers [22).
After the all parts are aligned without tension, fully tighten all screws as
specified in the parts list.
MOUNTING INSTRUCTIONS
Adapter kit for Sys Bag
Thank you for choosing this premium product from SW-MOTECH. Please visit
ourwebshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and
pay attention to all relevant information in the vehicle manual during
assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behavior and/or stability of
your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections
previously removed are properly replaced. Also make sure that no moving parts
are obstructed and no function of the vehicle is hindered in any way. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions. After the first 50 km and then at
regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
S tep
| No.| **Item No./ Description *| Part| Quantity****|
N-m ..
---|---|---|---|---|---
|
1
| HTA.00.152.080| Guide Bolt| 4 /4|
2
| HTA.00.152.081| Lock Bolt| 1 /1|
3
| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1 /1| ****
4
| M6 x 25; DIN 6912| Hexagon Socket Screw, short head| 1 /1| ****
5
| M6x35;DIN6912| Hexagon Socket Screw, short head| 1 /1| ****
6
| M6 x 22; DIN 7991| Countersunk Screw; black| 3/3| ****
7
| M6 x 35; DIN 7991| Countersunk Screw; black| 3/3| ****
8
| M6; DIN 6927| Lock Nut with Flange; black| 4 /4|
9
| M6; DIN 985| Lock Nut| 4 /4|
••••: Tightening torque see illustration
- All measurements in millimeters. • ** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
PRO side carrier and adapter plate for Sisal 15
Attach the shown parts to your PRO side carrier [right PRO side carrier
shown).
Tighten the screws as specified in the illustration .
Adapter plate for STREET-RACK and adapter plate for Sys Bag 10 / 15 Attach the
shown parts to your Adapter plate for STREET-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
STEEL-RACK and adapter plate for Sys Bag 15
Attach the shown parts to your STEEL-RACK.
ATTENTION: Use liquid thread locker (screws (6) only)!
Tighten the screws as specified in the illustration.
EVO side carrier and adapter plate for Sys Bag 30
Attach the shown parts to your EVO side carrier [right EVO side carrier
shown).
Tighten the screws as specified in the illustration.
PRO side carrier and adapter plate for Sys Bag 30
Attach the shown parts to your PRO side carrier [right PRO side carrier
shown).
Tighten the screws as specified in the illustration.
STEEL-RACK and adapter plate for Sys Bag 30 Attach the shown parts to your
STEEL-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
ADVENTURE RACK and adapter plate for Sys Bag 30
Attach the shown parts to your
ADVENTURE RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
Adapter plate for ALU-RACK and adapter plate for Sys Bag 30
Attach the shown parts to your Adapter plate for ALU-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
Adapter plate for STREET-RACK and adapter plate for Sys Bag 30 Attach the
shown parts to your Adapter plate for STREET-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
MOUNTING INSTRUCTIONS
Adapter plate for Sys Bag 30
Thank you for choosing this premium product from SW-MOTECH.
Please visit ourwebshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and
pay attention to all relevant information in the vehicle manual during
assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behavior and/or stability of
your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
| Step | No. | Item No. / Descdption * | Part | Quantity | N.· m *** |
|---|---|---|---|---|---|
| SYS.00.003.10000R/B | Adapter Plate for SysBag 30 right | ||||
| 1 | SYS.00.003.001 | Adapter Plate | 1 /1 | ||
| 2 | HTA.00.864.5O0 .05 | Locking Mechanism | 1 /1 | ||
| 3 | HTA.00.864.01 1i | Locking Adapter | 3 /3 | 3 | |
| 4 | M5 x 16· ISO 7380 | Lenshead Screws; blaick | 16 /16 | ||
| 5 | M5; DIN 985 | Lock Nut | 16 /16 | ||
| 6 | Countersunk Screw | 4 /4 | 15 | ||
| 7 | Countersunk Space.r | 4 /4 | |||
| 8 | Sleeve Nut | 4 /4 | |||
| SYS.00.003.10000R/B | Adepter Plate for SysBag 30 Left | ||||
| 1 | SYS.00.003.001 | Adapter Plate | 1 /1 | ||
| 2 | HTA.00.864.500.06 | Locking Mechanism | 1 /1 | ||
| 3 | HTA.00.864.014 | Locking Adapter | 3 /3 | ||
| 4 | M5 x 16; ISO 7380 | Lenshead Screws; black | 16 /16 | 3 | |
| 5 | **** M5; DIN 985 | Lock Nut | 16 /16 | ||
| **** | **** | ||||
| 6 | MB x 16; DIN 7991 | Countersunk Screw | 4 /4 | 15 | |
| 7 | SYS.00.001 .003 | Countersunk Spacer | 4 /4 | ||
| 8 | SYS.00.001.002 | Sleeve Nut | 4 /4 |
- All measurements in millimeters. • ** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufactural’! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
Configuration A for:
EVO side carrier
PRO side carrier
NOTE: The mounting steps [1] to [3] show the mounting of the right adapter
plate. Mount the left adapter plate in the same way as on the right side.
Mount the shown parts on the other side of the adapter plate.
ATTENTION: Pay attention to the markings (parallelogram or
triangle) which define the respective mounting side (see detail
drawing on the top right side)!
Configuration B for:
Adapter plate for ALU-RACK
Adapter plate for STREET-RACK
STEEL-RACK
ADVENTURE-RACK
ATTENTION: Make sure that the locking mechanism (2) and the lock bolt of
the adapter kit for Sys Bag 15/30 are mounted opposite to each other!
Attach the parts (2) to (5) to the adapter plate (1). as shown in the drawing.
Tighten the screws as specified in the parts list.
Attach the adapter plate (1) to your SysBag 30, as shown in the drawing.
Pay attention to the alignment of the lid of the SysBag 30.
ATTENTION: Use medium-strength liquid thread locker!
Tighten the screws as specified in the parts list.
Place the locking openings of the locking mechanism (2) and the locking
adapter (3] onto the guide bolts of the adapter kit for Sys Bag 15/30 (sold
separately).
Then press the Sys Bag 30 onto the guide bolts, until it properly rests on
your
SW-MOTECH carrier system.
ATTENTION: Make sure that all guide bolts of the adapter kit for Sys Bag
15/30 engage at the same time! Pay attention to the clearly audible snap sound
of the locking mechanism and that the red marking under the slider is not
visible!
To release press the slider downward or pull the release cord.
MOUNTING INSTRUCTIONS
Sys Bag 10 / 15 / 30
Thank you for choosing this premium product from SW-MOTECH.
Please visit ourwebshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance
work!
Carefully follow all the directions given in the mounting instructions and
pay attention to all relevant information in the vehicle manual during
assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behavior and/or stability of
your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type. After fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way.
Lamps as taillight and turn signals must not be limited in their function.
Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
Maximum Load
|
Maximum Speed
---|---
5 KG [11 lbs.) per Sys Bag 10 & 15| 130 km/h [80 mph)
1 0 KG [22 lbs.) per Sys Bag 30
PARTS LIST
Step
| No.| Item No. / Description •| Parts| Quantity • •|
N-m • • •
---|---|---|---|---|---
| | BC.SYS.00.001 .1 0000| Sysbag 10| |
|
1
| BC.SYS.00.001 .1 0000| Sysbag 10|
1 /1
|
2
| BC.ZUB.00.004.30000| Lashing Eye Set 12 pieces)|
1 /1
|
3
| BC.ZUB.00.094.30000| Waterproof lnnerbag|
1 /1
|
|
| BC.SYS.00.001 .1 0000| Sysbag 15|
|
|
1
| BC.SYS.00.001 .1 0000| Sysbag 15|
1 /1
|
2
| BC.ZUB.00.004.30000| Lashing Eye Set 12 pieces)|
1 /1
|
3
| BC.ZUB.00.094.30000| Waterproof lnnerbag|
1 /1
|
|
| BC.SYS.00.001 .1 0000| Sysbag 30|
|
|
1
| BC.SYS.00.001 .1 0000| Sysbag 30|
1 /1
|
2
| BC.ZUB.00.004.30000| Lashing Eye Set 12 pieces)|
1 /1
|
|
| | |
|
|
| | all Sysbag|
|
|
4
| SYS.00.001.004| Rubber plug|
4 /4
|
5
| SYS.00.001.004| Adhesive Protection Foil|
1 /1
|
6
| BC.ZUB.00.097.30000| Loop Strap Set 14 pieces)|
1 /1
|
7
| BC.ZUB.00.098.30000| Shoulder Strap|
1 /1
|
- All measurements in millimeters. – “””The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
FASTENING
ASTENING TO THE VEHICLE
ATTENTION: Before fastening your Sys Bag (1 I to the vehicle, the rear
eyelets must be closed with the included rubber plugs (4) (shown in the detail
drawing at the top)!
ATTENTION: Protect sensitive surfaces in the area of the Sys Bag (1) and
the fastening straps with the adhesive protection foil (5) from scratches!
Place your Sys Bag (1) in the rear area of your vehicle (e.g. passenger
seat, luggage rack etc..
On both sides entangle TWO loop straps (6) to appropriate and reliable
attachment points in the rear area of the vehicle (e.g. luggage hook etc..
TIP: SW-MOTECH recommends the mounting with the lashing eyes (2) (only
Sys Bag 10 and 15). Attach the lashing eyes (2) with the original screws
behind your license plate.
Then entangle on both sides TWO loop straps (6) to appropriate and reliable
attachment points of the vehicle (e.g. vehicles frame, footrest mounts etc.).
Attach the hook buckles of the loop straps (6) on both sides to the marked
loops of the SysBag (11, as shown in the lower drawing.
Tighten all loop straps until the Sys Bag (1 I is centered and securely
fastened to the vehicle. Secure the overlength of the loop straps (6) with the
rubber loops.
FASTENING TO THE SYSBAG 15 (Optional)
Attach your Sys Bag 15 [A) to the vehicle as described in step [1] Loosen the
upper
two straps of the vehicle-mounted Sys Bag 15 (A).
Attach the hook buckles of the two straps to the shown loops (behind the lid)
of the Sys Bag 10 or 15 (B).
On both sides, loosen the upper straps on each side of the Sys Bag 10/151B).
Attach the hook buckles of the two straps to the loops shown on the attached
Sys Bag 15 (A).
After ALL FOUR hook buckles are properly hooked, tighten the straps until the
Sys Bag 10/15 (BLM is firmly attached on the Sys Bag 15 (A). Secure the
overlength of the straps (4) with the Velcro loops against flapping.
FUNCTION CHECK (MUST BE OBSERVED)
ATTENTION: All components of the **Sys Bag must not contact any hot or
moving parts of the vehicle. All parts should also remain 15 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. For this reason
compress the suspension fully several times with your vehicle stationary.
**
LOADING and CARE
ATTENTION: Always use the included waterproof inner bag (3) to protect your
luggage from moisture!
Fasten the waterproof inner bag (3) on the inside of the reinforced opening of
the Sys Bag (1).
Now roll the reinforced opening three times. Then close the Sys Bag 11 I with
the buckles.
LOADING
ATTENTION: Pay attention to keep items and electronic devices that can be
damaged by magnetic fields away from the magnets sewn in the lid of the Sys
Bag (1)!
ATTENTION: Never store pointy orchard-edged objects, which could cause
injury to persons or damage to the vehicle/side case!
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy
water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the Sys Bag after riding in salty conditions, to avoid damage from salt.
COMBINATIONS
COMBINATIONS
The Sys Bag line has only three bags but offers over 20 mounting options and
combination possibilities. The bags can be lashed to the tail end or at the
side, as described in the mounting instructions, or mounted to the carrier/
rack with a quick-release fastener. On this page you will find some mounting
examples.
Vehicle-specific solutions, Sys Bag sets and adapter plates for SW-MOTECH
carriers/ racks can be found in our webshop.
Customer Support
S W-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel./ phone+ 49 (0)6425 / 8168 – 050
Fax/ fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Documents / Resources
| SW-
MOTECH BC.SYS.01.548.20000 SysBag 30 Bag
System
[pdf] Instruction Manual
BC.SYS.01.548.20000, SysBag 30 Bag System, BC.SYS.01.548.20000 SysBag 30 Bag
System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>