thumbsUp LEDCARLIT Car Interior LED Lights Instructions

LEDCARLIT Car Interior LED Lights
Instructions

ARTWORK INFORMATION PANEL

ARTWORK TITLE: Primark 8S22 Powerbank 10,000 Manual
ARTWORK TYPE:
PACKAGING MANUAL STICKER

MATERIAL: 80gsm
FINISH:
CUTTER GUIDE SIZE: H 110mm x W 45mm (Folded)
PRODUCT CODE:
BARCODE:
TYPE: EAN 13, 80%

FONT LISTING:

NOTES:
DOUBLE SIDED PRINT
FOLDED MANUAL SIZE: H 110mm x W 70mm
UNFOLDED MANUAL SIZE: H 110mm x W 560mm

VERSION DATE:

PLEASE MAKE SURE ALL FONTS HAVE BEEN OUTLINED, AND ALL IMAGES EMBEDDED.

The symbol is shown here and, on the product, means that the product is classed as Electrical or Electronic Equipment and should not be disposed of with other household or commercial wane at the end of its working life. The Wade Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) has been put in place to encourage the recycling of products using be available recovery and recycling techniques to minimize the impact on the environment, treat any hazardous subtleness and avoid the increase of landfill. When you have no further use for this product, please dispose of it using your local authority’s recycling processes. For more information, please contact your local authority or the retailer where the product was purchased.

Specifications:

Contents:

1. LED Strip Lights
2. Remote Control

installing Sound Reactive Car LED Light Strips
we recommend installing these in the footwell of your car or in lower places to avoid any impediment of driving through glare on windows.
Note – installing these into your vehicle is at your own risk and Primark will not be held accountable for any damage or loss caused by using these.

1. Identify the position you would like to install the LED light and ensure that the cable can be securely fastened in the below ways;
   i. Cable ties the cable to a suitable are ensuring you do not impede any critical functions for driving
   ii. Place the cable under the floor mat, ensuring you do not impede any critical functions for driving
   iii. Carefully remove or place the cable behind the inner car paneling ensuring you do not impede any critical functions for driving.

2. Clean the area where you intend to install the lights with a damp cloth and dry the area

3. Once the area is dry, remove the protective tape and apply it to the chosen area. Ensure you push firmly to help the product stick.

4. Repeat for other areas within your car.
   Note:
   – Do not attempt to disassemble or repair the product.
   – Please store in a dry place.
   – LED bulbs are not replaceable.
   – Keep the batteries compartment and other electronic parts away from water.
   – Use the Sound Reactive LED Strip Light in the environment with a temperature between
   -10°C and 40°C, otherwise, it may damage the product.
   – Retain and store packaging safely for future reference.
   -This product is designed for indoor use only.
   – Ensure the product does not impede driving view or conditions, please check the local road safety department to ensure you meet your country’s requirements
   – Ensure cables are not covered or impeding any vital controls or access points within the car as this can cause serious injury
   – Do not use the remote when operating the vehicle.

Caution: Do not ingest battery, Chemical Burn Hazard. This product contains a button cell battery. If the cell is swallowed it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely stop using the product and keep it away from children. If you think the batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection againS1 harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and If not installed and used In accordance with the instructions, may cause harmful interference to radio communication. However. there is no guarantee that interference will not occur In a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user in encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that of which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

Magnum Brands Limited,
Ruislip, HA4 OEJ, UK
Magnum Brands (EU) Limited Herbert House, 18-22 Pembroke Rd, Dublin 4, Ireland
Magnum Brands Inc. 19 West 34th Street, RM 1018 New York, NY 10001- 3006
For more product information please visit www.Thumbsup.com
E&OE Images and illustrations may differ from actual products.
WARNING
KEEP OUT OF REACH OF CHILDREN Swallowing can lead to chemical bums, perforation of soft tissue. and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately

LEDCARLIT
MADE IN CHINA

Documents / Resources

| thumbsUp LEDCARLIT Car Interior LED Lights [pdf] Instructions
LEDCARLIT, Car Interior LED Lights
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>