SW-MOTECH BC.SYS.11.953.20000 SysBag 30 Bag System Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
NBAUANLEITUNG
ANBAUANLEITUNG
mounting instructions
BC.SYS.11.953.20000/B
contains
KFT.11.953.30000/B SYS.00.001.13000
SYS.00.003.10000L/B SYS.00.003.10000R/B BC.SYS.00.003.10000
MOUNTING INSTRUCTIONS
Revision: 00 Datum /Date: 07 – 2020
PRO side carrier
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop. Installation
and/or maintenance of this product require good technical understanding! For
your own safety SW-MOTECH recommends having installation and/or servicing
carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist. This product was developed for
vehicles in their factory setting. Compatibility with original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state of maintenance. Installed accessories can change the
driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority. PREPARATION: Read the mounting instructions carefully and make sure
that all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled
in accordance with the vehicle manufacturers· specifications or replaced by
parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified,
with medium-strength liquid thread locker. Torque specifications undefined by
SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist
workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular ntervals, check the tightening torque of all screw connections and
the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: The indicated maximum load is inclusive the weight of
case/luggage and adapter kit! The maximum vehicle load specified by the
manufacturer must not be exceeded! The side carriers are designed exclusively
for the use of SW-MOTECH adapter kits.
Dismount the side carriers when travelling without cases/luggage. Always use
the side carriers in pairs.
ATTENTION: Make sure that after attaching the luggage to the vehicle it
is not in the exhaust flow! Dangers of burns!
PARTS LIST
| Part | Anzahl” Quantity’ | N.m |
|---|---|---|
| Mounting Tab | 2/3 | 20 |
| Hexagon Socket Screw | 2/3 | |
| Washer | 4/7 | |
| Spacer; black | 2/2 | |
| Lock Nut | 2/4 | |
| Mounting Tab | 2/2 | |
| Countersunk Screw | 2/2 | |
| Washer | 2/2 | |
| Spacer | 2/2 | 20 |
| Lock Nut | 2/4 | |
| Mounting Tab | 1/1 | |
| Spacer | 1/1 | |
| Mounting Tab; right | 1/1 | |
| Hexagon Socket Screw | I /1 | |
| Washer | 1/1 | 20 |
| Crossbar | 1/7 | |
| Hexagon Socket Screw | I /1 | |
| Washer | 3/3 | 8 |
| Lock Nut | 3/6 | |
| Side Carrier; left/ right | 2/2 | |
| Quick Fastener with Lock Washer | 8/8 |
8.8
| ) Regelgewinde / Coarse Thread | M% | M5 | M6 | Me | e 1o/ | M12] |
|---|---|---|---|---|---|---|
| Stahl FK 8.8 /Steel CL 8.8 N· | 2,8 | 5,5 | 9,6 | 23 | 46 | 79 |
10.9
| Regelgewinde / Coarse Thread 0 | ML | MS] | M | M8 | M10 | M12 |
|---|---|---|---|---|---|---|
| Stahl FK 10.9/Steel CL 10.9 N·m | 4,1 | 8,1 | 14 | 34 | 67 | 115 |
Anmerkungen. ” Ale Ma~angaben in Millimeter, Der zweite Wert gibt die
Gesamtanzah! des jew. Artikels in den an. Keine Anzugsmomentvorgabe: Verwenden
Sie das vom Fzg.-Hersteller definierte Anzugsmoment! der Tabelle kann
verwendet werden, wenn es den Fzg.-Hersteller-Vorgaben entspricht,
Note · All measurements in millimeters P The second number indicates the total
the part in the delivery. torque in this table can No torque specifications:
Use the torque defined by vehicle manufacturer! The be used as long as it is
within the vehicle manufacturer s specifications. ‘
Copyright by
SW-MOTECH GmbH & Co. KG
Errors and omissions excepted. Technical and design modifications are subject
to change
MOUNTING
Remove the pillion seat and seat from the vehicle. On vehicles with seat heating, the plug of the seat must be discon nected.
Remove the shown screws, diconnect the plug and remove the control unit with the cover from the vehicle.
Remove the shown screws and nuts on both sides of the tail of the vehicle.
Then remove the passenger footrest on the left side of the vehicle.
ATTENTION: Dismount the side carriers (20) when travelling without sidecases!
Use the fasteners [21 I to connect the side carriers [20] to the mounting tabs
[(1), (6), [11) and (13) and the cross bar [16].
Secure the fasteners [21 I with the lock washers.
Once all the parts are evenly positioned without excess tension, tighten the
screws as specified.
Tighten the original screws (Orig.l with the manufacturers’ specified torque.
NOTE: The Ant-Theft Device is sold separately.
PARTS LIST
Part| Azah[
Quantity| N.m .. ,
---|---|---
Guide Bolt| 4/1|
Lock Bolt| 1/1|
Hexagon Socket Screw, short head| 1/1|
Hexagon Socket Screw, short head| 1/1|
Hexagon Socket Screw, short head| 1/1|
Countersunk Screw; black| 1/1|
Countersunk Screw; black| 3/3|
Lock Nut with Flange; black| 3/3|
Lock Nut| 4/4|
++++: Tightening torque see illustration| 4/4|
PRO side carrier and adapter plate for SysBag 15
Attach the shown parts to your PRO side carrier [right PRO side carrier
shown).
Tighten the screws as specified in the illustration.
Adapter plate for STREET-RACK and adapter plate for Sys Bag 10 / 15
Attach the shown parts to your Adapter plate for STREET-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other! Tighten the
screws as specified in the illustration.
STEEL-RACK and adapter plate for SysBag 15 Attach the shown parts to your
STEEL-RACK.
ATTENTION: Use liquid thread locker (screws (6) only)! Tighten the screws as
specified in the illustration.
ADVENTURE RACK and adapter plate for SysBag 15 Attach the shown parts to your
ADVENTURE RACK.
ATTENTION: Use liqu id threadlocker (screws (6) only)!
Tighten the screws as specified in the illustration.
EVO side carrier and adapter plate for SysBag 30
Attach the shown parts to your EVO side carrier [right EVO side carrier
shown).
Tighten the screws as specified in the illustration.
PRO side carrier and adapter plate for SysBag 30 Attach the shown parts to
your PRO side carrier (right PRO side carrier shown I.
Tighten the screws as specified in the illustration.
STEEL-RACK and adapter plate for SysBag 30 Attach the shown parts to your
STEEL-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
ADVENTURE RACK and adapter plate for SysBag 30 Attach the shown parts to your
ADVENTURE RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
Adapter plate for ALU-RACK and adapter plate for SysBag 30 Attach the shown
parts to your Adapter plate for ALU-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
Adapter plate for STREET-RACK and adapter plate for SysBag 30 Attach the shown
parts to your Adapter plate for STREET-RACK. ATTENTION: Make sure that the
locking mechanism of the adapter plate for SysBag and the lock bolt (2) are
mounted opposite to each other!
Tighten the screws as specified in the illustration.
| Part | Azah Qantity | .***N.m |
|---|---|---|
| Adapter Plate | 1/1 | |
| Locking Mechanism | 1/1 | |
| Locking Adapter | 3/3 | |
| Lenshead Screws; black | 16/16 | 3 |
| Lock Nut | 16/16 | |
| Countersunk Screw | 4/4 | 16 |
| Countersunk Spacer | 4/4 | |
| Sleeve Nut | 4/4 | |
| Adpter plate for sysBag 30left | ||
| Adapter Plate | 1/1 | |
| Locking Mechanism | 1/1 | |
| Locking Adapter | 3/3 | |
| Lenshead Screws; black | 16/16 | 3 |
| Lock Nut | 16/16 | |
| Countersunk Screw | 4/4 | 15 |
| Countersunk Spacer | 4/4 | |
| Sleeve Nut | 4/4 |
MOUNTING
Configuration A for:
EVO side carrier
PRO side carrier
NOTE: The mounting steps [1] to [3] show the mounting of the right
adapter plate. Mount the left adapter plate in the same way as on the right
side. Mount the shown parts on the other side of the adapter plate.
ATTENTION: Pay attention to the markings (parallelogram or triangle) which
define the respective mounting side (see detail drawing on the top right
side)!
Attach the parts (2) to [5) to the adapter plate [11. as shown in the drawing.
Tighten the screws as specified in the parts list.
Configuration B for:
Adapter plate for ALU-RACK
Adapter plate for STREET-RACK
STEEL-RACK
ADVENTURE-RACK
ATTENTION: Make sure that the locking mechanism (2) and the lock bolt of the
adapter kit for SysBag 15/30 are mounted opposite to each other!
Attach the parts (2) to [5) to the adapter plate [11, as shown in the drawing.
Tighten the screws as specified in the parts list.
Attach the adapter plate [1) to your SysBag 30, as shown in the drawing.
Pay attention to the alignment of the lid of the SysBag 30.
ATTENTION: Use medium-strength liquid thread locker!
Tighten the screws as specified in the parts list.
Place the locking openings of the locking mechanism [2) and the locking
adapter [3) onto the guide bolts of the adapter kit for SysBag 15/30 [sold
separately). Then press
the SysBag 30 onto the guide bolts, until it properly rests on your SW-MOTECH
carrier system.
• ATTENTION: Make sure that all guide bolts of the adapter kit for SysBag
15/30 engage at the same time! Pay attention to the clearly audible snap sound
of the locking
mechanism and that the red marking under the slider is not visible!
To release press the slider downward or pull the release cord.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation
of the product!
| Part | Azah Qantity | Nm **** |
|---|---|---|
| SysBag 10 | ||
| Sys Bag 10 | 1/1 | |
| Lashing Eye Set 12 pieces) | 1/1 | |
| Waterproof lnnerbag | 1/1 | |
| SysBag 15 | ||
| SysBag 15 | 1/1 | |
| Lashing Eye Set 12 pieces) | 1/1 | |
| Waterproof lnnerbag | 1/1 | |
| all SysBages | ||
| Sys Bag 30 | 1/1 | |
| Waterproof lnnerbag | 1/1 | |
| Rubber Plug | 4/4 | |
| Adhesive Protection Foil | 1/1 | |
| Loop Strap Set (4 pieces] | 1/1 | |
| Shoulder Strap | 1/1 |
FASTENING
FASTENING TO THE VEHICLE
ATTENTION: Before fastening your SysBag [1 I to the vehicle, the rear eyelets
must be closed with the included rubber plugs [4) [shown in the detail drawing
at the top)!
ATTENTION: Protect sensitive surfaces in the area of the SysBag [1) and the
fastening straps with the adhesive protection foil (5) from scratches!
Place your SysBag [1] in the rear area of your vehicle [e.g. passenger seat,
luggage rack etc.I.
On both sides entangle TWO loop straps [6) to appropriate and reliable
attachment points in the rear area of the vehicle [e.g. luggage hook etc.I.
TIP: SW-MOTECH recommends the mounting with the lashing eyes [2l !only Sys Bag
10 and 15). Attach the lashing eyes [21 with the original screws behind your
license plate. Then entangle on both sides TWO loop straps [6) to appropriate
and reliable attachment points of the vehicle le.g. vehicles frame, footrest
mounts etc.I.
Attach the hook buckles of the loop straps [6) on both sides to the marked
loops of the SysBag (1l, as shown in the lower drawing.
Tighten all loop straps until the SysBag (1) is centered and securely fastened
to the vehicle. Secure the overlength of the loop straps [6] with the rubber
loops.
FASTENING TO THE SYSBAG 15 (Optional)
Attach your SysBag 15 [Al to the vehicle as described in step [1]. Loosen the
upper two straps of the vehicle-mounted SysBag 15 [Al.
Attach the hook buckles of the two straps to the shown loops [behind the lid[
of the Sys Bag 10 or 15 [Bl. On both sides, loosen the upper straps on each
side of the SysBag
10/15 [Bl. Attach the hook buckles of the two straps to the loops shown on the
attached SysBag 15 [Al.
After ALL FOUR hook buckles are properly hooked, tighten the straps until the
SysBag 10/15 [Bl is firmly attached on the SysBag 15 [Al. Secure the
overlength of the straps
[41 with the velcro loops against flapping.
FUNCTION CHECK (MUST BE OBSERVED)
ATTENTION: All components of the SysBag must not contact any hot or moving
parts of the vehicle. All parts should also remain 15 cm away from hot parts
of the vehicle and remain clear of the exhaust stream. For this reason
compress the suspension fully several times with your vehicle stationary.
LOADING and CARE
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy
water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer I Clean the SysBag after riding in salty conditions, to avoid damage
from salt.
COMBINATIONS
COMBINATIONS
The SysBag line has only three bags but offers over 20 mounting options and
combination possibilities. The bags can be lashed to the tail end or at the
side, as described in the mounting instructions, or mounted to the carrier /
rack with a quick-release fastener. On this page you will find some mounting
examples. Vehicle-specific solutions, SysBag sets and adapter plates for SW-
MOTECH carriers/ racks can be found in our webshop.
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg Germany
Tel./ phone+ 49 10)6425 / 8168 – 050
Fax/ fax+ 49 [0)6425 / 8168- 10
info@sw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>