SW-MOTECH BC.SYS.06.593.20000B SysBag 30 Bag System Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.SYS.06.593.20000B SysBag 30 Bag System
MOUNTING INSTRUCTIONS
EVO carrier
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webs hop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webs hop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION
Read the mounting instructions carefully and make sure that all items of
the parts list are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Use appropriate tools. Have another person
to help you.
MOUNTING
All parts and connections removed from the vehicle must be reinstalled in
accordance with the vehicle manufacturers· specifications or replaced by parts
delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with
medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK
After installation make sure that all parts and connections previously removed
are properly replaced. Also make sure that no moving parts are obstructed and
no function of the vehicle is hindered in any way. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions. After the first 50 km and then at regular intervals, check
the tightening torque of all screw connections and the proper fit of the
product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: The indicated maximum load is inclusive the weight of
case/luggage and adapter kit The maximum vehicle load specified by the
manufacturer must not be exceeded!
The side carriers are designed exclusively for the use of SW-MOTECH Adapter
Kits.
Dismount the side carriers when travelling without cases/luggage. Always use
the side carriers in pairs.
ATTENTION: Make sure that after attaching the luggage to the vehicle it
is NOT in the exhaust flow! Dangers of burns!
PARTS LIST
| S]Step | ]No. | ]Item No. / Description * | Part | Quantity ** | Nm *** |
|---|---|---|---|---|---|
| 1 | (1) | KFT.06.593.003 | Mounting Bracket | 2 | / 2 |
| (2) | M8 x 40; DIN 6912 | Hexagon Socket Screw, short Head; black | 4 | / 4 | 20 |
| (3) | d 8,4; DIN 125 | Washer; black | 4 | **** / 6 | |
| (4) | KFT.06.593.002 | Mounting Bracket | 2 | **** / 2 | |
| (5) | M8 x 45; DIN 6912 | Hexagon Socket Screw, short Head; black | 2 | **** / 2 |
20
(6)| d 8,4; DIN 125| Washer; black| 2| / 6|
(7)| Ø 20 / ø 8,4 / h 22| Spacer| 2| / 2|
(8)| Ø 12 / ø 8,4 / h 4| Spacer| 2| ** / 2|
| | | |
2| (9)| KFT.06.593.001L / R| Mounting Bracket; left / right| 2| / 2|
| (10)| M8 x 16; DIN 933| Hexagon Screw; full thread| 4| / 4| 18
(11)| d 8, 4; DIN 125| Washer| 4| / 4|
| | | |
3| (12)| KFT.06.478.003| Crossbar| 1| ** / 1|
| (13)| M6 x 20; DIN 912| Hexagon Socket Screw| 2| ** / 2| 8
(14)| d 6,4; DIN 9021| Washer| 4| / 4|
(15)| M6; DIN 6927| Lock Nut with Flange| 2| / 2|
| | | |
4| (16)| KFT.06.593.961 / 962| Side Carrier; left / right| 2 / 2|
| (17)| CAM.2312S21-12AHNV| QUICK-LOCK Fastener| 8 / 8|
(18)| CAM.2312S10-1BP| Lock Washer| 8 / 8|
| | | |
10.9| Regelgewinde / Coarse Thread| Ø| M4| M5| M6|
M8| M10| M12|
Stahl; FK 10.9 / Steel; CL 10.9| Nm**| 4,1| 8,1| 14| 34| 67| 115|
Al measurements in millimeters.
The second number indicates the total quantity of the part in the delivery.
No torque specifications:
Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used as long as it is within the
vehicle manufacturers specifications.
MOUNTING
Remove the original screws from the mounting points.
Attach the mounting brackets (1) and (4) on both sides to the vehicle, as
shown in the drawing. ATTENTION: Use liquid thread locker!
Do not fully tighten the screws yet.
Attach the mounting brackets (9) on both sides to the footrest mounts, as
shown in the drawing.
ATTENTION: Use liquid thread locker!
Do nut fully tighten the screws yet.
Mount the Crossbar (12) to the license plate holder, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Do not fully tighten the screws yet.
Use the fasteners (17) to connect the side carriers (16) to the crossbar (12)
and mounting brackets (1), (4) and (9). Secure the the fasteners with the lock
washers (18).
Once all the parts are evenly positioned without excess tension, tighten the
screws as specified in the parts list.
NOTE: The Anti-Theft Device is sold separately.
Adapter kit for SysBag
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webs hop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webs hop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION
Read the mounting instructions carefully and make sure that all items of
the parts list are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Use appropriate tools. Have another person
to help you.
MOUNTING
All parts and connections removed from the vehicle must be reinstalled in
accordance with the vehicle manufacturers· specifications or replaced by parts
delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with
medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK
After installation make sure that all parts and connections previously removed
are properly replaced. Also make sure that no moving parts are obstructed and
no function of the vehicle is hindered in any way. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions. After the first 50 km and then at regular intervals, check
the tightening torque of all screw connections and the proper fit of the
product.
PARTS LIST
Step| No.| N o . / D es c ription| Part|
Q uantity ..| N·m “‘
---|---|---|---|---|---
| (1)| HTA.00.152.080| Guide Bolt| 4 /4|
(2)| HTA.00.152.081| Lock Bolt| 1 /1|
(3)| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1 /1| **
(4)| M6 x 25; DIN 6912| Hexagon Socket Screw, short head| 1 /1| **
(5)| M6 x 35; DIN 6912| Hexagon Socket Screw, short head| 1 /1|
(6)| M6 x 22; DIN 7991| Countersunk Screw; black| 313|
(7)| M6 x 35; DIN 7991| Countersunk Screw; black| 313| **
(8)| M6; DIN 6927| Lock Nut with Flange; black| 4 /4|
(9)| M6; DIN 985| Lock Nut| 4 /4|
| | **: Tightening torque see illustration| |
Regelgewinde / Coarse Thread III I M4 M5 M6 MSIM10IM12
Stahl FK 10.9 / Steel CL 10.9 N·m I 4, 1 8,1 14 34 I 67 1115
Al measurements in millimeters.
The second number indicates the total quantity of the part in the delivery.
No torque specifications:
Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used as long as it is within the
vehicle manufacturers specifications.
MOUNTING
PRO side carrier and adapter plate for Sys Bag 15
Attach the shown parts to your PRO side carrier [right PRO side carrier
shown).
Tighten the screws as specified in the illustration .
Adapter plate for STREET-RACK and adapter plate for Sys
Bag 10 / 15
Attach the shown parts to your Adapter plate for STREET-RACK. ATTENTION: Make
sure that the locking mechanism of the adapter plate for Sys Bag and the lock
bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
STEEL-RACK and adapter plate for Sys Bag 15
Attach the shown parts to your STEEL-RACK.
ATTENTION: Use liquid thread locker (screws (6) only)!
Tighten the screws as specified in the illustration.
ADVENTURE RACK and adapter plate for Sys Bag 15
Attach the shown parts to your ADVENTURE RACK.
ATTENTION: Use liquid thread locker (screws (6) only)!
Tighten the screws as specified in the illustration.
EVO side carrier and adapter plate for Sys Bag 30
Attach the shown parts to your EVO side carrier [right EVO side carrier
shown).
Tighten the screws as specified in the illustration.
PRO side carrier and adapter plate for Sys Bag 30
Attach the shown parts to your PRO side carrier [right PRO side carrier
shown).
Tighten the screws as specified in the illustration.
STEEL-RACK and adapter plate for Sys Bag 30
Attach the shown parts to your STEEL-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
ADVENTURE RACK and adapter plate for Sys Bag 30
Attach the shown parts to your ADVENTURE RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the illustration.
Adapter plate for ALU-RACK and adapter plate for Sys Bag 30
Attach the shown parts to your Adapter plate for ALU-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
SysBag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
Adapter plate for STREET-RACK and adapter plate for Sys Bag 30
Attach the shown parts to your Adapter plate for STREET-RACK.
ATTENTION: Make sure that the locking mechanism of the adapter plate for
Sys Bag and the lock bolt (2) are mounted opposite to each other!
Tighten the screws as specified in the illustration.
Adapter plate for SysBag 30
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webs hop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION:
Read the mounting instructions carefully and make sure that all items of the
parts list are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Use appropriate tools. Have another person
to help you.
MOUNTING:
All parts and connections removed from the vehicle must be reinstalled in
accordance with the vehicle manufacturers· specifications or replaced by parts
delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with
medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK:
After installation make sure that all parts and connections previously removed
are properly replaced. Also make sure that no moving parts are obstructed and
no function of the vehicle is hindered in any way. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions. After the first 50 km and then at regular intervals, check
the tightening torque of all screw connections and the proper fit of the
product.
PARTS LIST
| Step | No. | Item No./ Description * | Part | Quantity | N· m”‘ |
|---|---|---|---|---|---|
| ■ | SYS.00.003. 10000R/B | Adapter Plate for **Sys | |||
| Bag 30 right** |
.
| 111| SYS.00.003.001| Adapter Plate| 1 /1|
(2)| HTA.00.864.500.05| Locking Mechanism| 1 /1|
(3)| HTA.00.864.011| Locking Adapter| 313|
(4)| M5 x 16; ISO 7380| Lensed Screws; black| 16/16| 3
(5)| M5; DIN 985| Lock Nut| 16/16|
| | | |
| MS x 16; DIN 7991| Countersunk Screw| 4 /4| 15
(7)| SYS.00.001 .003| Countersunk Spacer| 4 /4|
(Bl| SYS.00.001 .002| Sleeve Nut| 4 /4|
| | | |
| | | |
■| | SYS.00.003.10000L/B| Adapter Plate for SysBag 30
left| |
.
| 111| SYS.00.003.001| Adapter Plate| 1 /1|
(2)| HTA.00.864.500.06| Locking Mechanism| 1 /1|
(3)| HTA.00.864.014| Locking Adapter| 3 /3|
(4)| M5 x 16; ISO 7380| Lensed Screws; black| 16 /16| 3
(5)| M5; DIN 985| Lock Nut| 16/16|
| | | |
| MS x 16; DIN 7991| Countersunk Screw| 4 /4| 15
(7)| SYS.00.001.003| Countersunk Spacer| 4 /4|
(8)| SYS.00.001.002| Sleeve Nut| 4 /4|
| | | |
| Regelgewinde/ Coarse Thread 01 M4 I M5 I M6I MB I M1 0
I M12 StahlFK10.9/SteelCL10.9 N·m 4,1 8,1 14 34 67 115| |
|
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications:
Use the torque defined by vehicle manufactural’!
The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
Configuration A for:
EVO side carrier
PRO side carrier
NOTE: The mounting steps [1] to [3] show the mounting of the right
adapter plate. Mount the left adapter plate in the same way as on the right
side. Mount the shown parts on the other side of the adapter plate.
ATTENTION: Pay attention to the markings (parallelogram or triangle)
which define the respective mounting side (see detail drawing on the top right
side)!
Attach the parts (2) to (5) to the adapter plate (1). as shown in the drawing.
Tighten the screws as specified in the parts list. 
Configuration B for:
Adapter plate for ALU-RACK Adapter plate for STREET-RACK STEEL-RACK ADVENTURE-
RACK
ATTENTION: Make sure that the locking mechanism (2) and the lock bolt of
the adapter kit for Sys Bag 15/30 are mounted opposite to each other!
Attach the parts (2) to (5) to the adapter plate (1). as shown in the drawing.
Tighten the screws as specified in the parts list.
Attach the adapter plate (1) to your SysBag 30, as shown in the drawing. Pay
attention to the alignment of the lid of the Sys Bag 30.
ATTENTION: Use medium-strength liquid thread locker!
Tighten the screws as specified in the parts list.
Place the locking openings of the locking mechanism (2) and the locking
adapter (3) onto the guide bolts of the adapter kit for SysBag 15/30 (sold
separately). Then press the SysBag 30 onto the guide bolts, until it properly
rests on your
SW-MOTECH carrier system.
ATTENTION: Make sure that all guide bolts of the adapter kit for SysBag
15/30 engage at the same time! Pay attention to the clearly audible snap sound
of the locking mechanism and that the red marking under the slider is not
visible!
To release press the slider downward or pull the release cord.
Sys Bag 10 / 15 / 30
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webs hop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webs hop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION:
Read the mounting instructions carefully and make sure that all items of the
parts list are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Use appropriate tools. Have another person
to help you.
FUNCTION CHECK:
This is a universal product. For this reason make sure BEFORE the first use,
that the product can be fixed properly and used without problems with your
vehicle type. After fixation also make sure that no moving parts are
obstructed and the function of the vehicle is not hindered in any way. Lamps
as taillight and turn signals must not be limited in their function. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
ATTENTION: The maximum vehicle load specified by the manufacturer and the maximum load of the SW-MOTECH carrier/rack must not be exceeded! NOT FOR OFFROAD4JSE!
PARTS LIST
| Step | No. | Item No./ Description * | Part | Quantity | N- m “‘ |
|---|---|---|---|---|---|
| ■ | BC.SYS.00.001.10000 | SysBag 10 | |||
| 111 | BC.SYS.00.001.10000 | SysBag 10 | 1 /1 | ||
| 12) | BC.ZUB.00.004.30000 | Lashing Eye Set 12 pieces) | 1 /1 | ||
| BC.ZUB.00.094.30000 | Waterproof lnnerbag | 1 /1 | |||
| ■ | BC.SYS.00.002.10000 | SysBag 15 | |||
| 111 | BC.SYS.00.002.10000 | SysBag 15 | 1 /1 | ||
| 12) | BC.ZUB.00.004.30000 | Lashing Eye Set 12 pieces) | 1 /1 | ||
| BC.ZUB.00.095.30000 | Waterproof lnnerbag | 1 /1 | |||
| 1 | BC.SYS.00.003.10000 | Sys8ag30 | |||
| 11) | BC.SYS.00.003.10000 | SysBag 30 | 1 /1 | ||
| 12) | BC.ZUB.00.096.30000 | Waterproof lnnerbag | 1 /1 | ||
| all SysBags | |||||
| .14 | ) | SYS.00.001 .004 | Rubber Plug | 4 /4 | |
| 15) | LSF.350.250 | Adhesive Protection Foil | 1 /1 | ||
| 16) | BC.ZUB.00.097.30000 | Loop Strap Set [4 pieces) | 1 /1 | ||
| 17) | BC.ZUB.00.098.30000 | Shoulder Strap | 1 /1 | ||
| Regelgewinde/ Coarse Thread 01 M4 I M5 I M6 1 MS I |
M1 0 I M12
StahlFK10.9/SteelCL10.9 N·m 4,1 8,1 14 34 67 115|
Al measurements in millimeters.
The second number indicates the total quantity of the part in the delivery.
No torque specifications:
Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used as long as it is within the
vehicle manufacturers specifications.
FASTENING
FASTENING TO THE VEHICLE
ATTENTION: Before fastening your SysBag (1) to the vehicle, the rear
eyelets must be closed with the included rubber plugs (4) (shown in the detail
drawing at the top)!
ATTENTION: Protect sensitive surfaces in the area of the SysBag (1) and
the fastening straps with the adhesive protection foil (5) from scratches!
Place your SysBag (1) in the rear area of your vehicle (e.g. passenger seat,
luggage rack etc.I.
On both sides entangle TWO loop straps (6) to appropriate and reliable
attachment points in the rear area of the vehicle (e.g. luggage hook etc.I.
TIP: SW-MOTECH recommends the mounting with the lashing eyes (2) (only
SysBag 10 and 15). Attach the lashing eyes (2) with the original screws behind
your license plate.
Then entangle on both sides TWO loop straps (6) to appropriate and reliable
attachment points of the vehicle (e.g. vehicles frame, footrest mounts etc.].
Attach the hook buckles of the loop straps (6) on both sides to the marked
loops of the SysBag (11, as shown in the lower drawing. Tighten all loop
straps until the Sys Bag (1 I is centered and securely fastened to the
vehicle.
Secure the overlength of the loop straps (6) with the rubber loops.
FASTENING TO THE SYSBAG 15 (Optional)
Attach your SysBag 15 (A) to the vehicle as described in step [1].
Loosen the upper two straps of the vehicle-mounted SysBag 15 (A). Attach the
hook buckles of the two straps to the shown loops (behind the lid) of the Sys
Bag 10 or 15 (B).
On both sides, loosen the upper straps on each side of the SysBag 10/15 (Bl.
Attach the hook buckles of the two straps to the loops shown on the attached
SysBag 15 (A).
After ALL FOUR hook buckles are properly hooked, tighten the straps until the
Sys Bag 10/15 (Bl is firmly attached on the SysBag 15 (A). Secure the
overlength of the straps (4) with the velcro loops against flapping.
FUNCTION CHECK (MUST BE OBSERVED)
ATTENTION: All components of the Sys Bag must not contact any hot or
moving parts of the vehicle. All parts should also remain 15 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. For this reason
compress the suspension fully several times with your vehicle stationary.
LOADING and CARE
ATTENTION: Make sure weight is evenly distributed between
the left and right Sys Bag. Make sure that the landing is secured against
shifting during the ride!
LOADING
ATTENTION: Pay attention to keep items and electronic devices that can be
damaged by magnetic fields away from the magnets sewn in the lid of the SysBag
[1)!
ATTENTION: Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/side case!
ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors [e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy
water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the Sys Bag after riding in salty conditions, to avoid damage from salt.
COMBINATIONS
The SysBag line has only three bags but offers over 20 mounting options and
combination possibilities. The bags can be lashed to the tail end or at the
side, as described in the mounting instructions, or mounted to the carrier/
rack with a quick-release fastener. On this page you will find some mounting
examples.
Vehicle-specific solutions, SysBag sets and adapter plates for SW-MOTECH
carriers/ racks can be found in our webshop.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>