HFCL ion4x_2 Access Point User Guide
- June 3, 2024
- HFCL
Table of Contents
HFCL ion4x_2 Access Point
Introduction
Thank you for purchasing our ion4x_2 Access Point. ion4x_2 is a cloud-managed 2×2:2 MU-MIMO Wi-Fi 6 certified Access Point that raises the bar for wireless performance and efficiency.
Packaging Content
- Mounting Kit
- (Pole Clamp (1),
- L PIlate(1),
- U Bolt (1),
- Hex nut (4),
- Screws (4)
ion4x 2 Specifications
- Peak Throughput(aggregate): Up to 1.78 Gbps (1202 Mbps for 5 GHz and 574 Mbps for 2.4 GHz)
- W-Fi Standard Support |802.11a/b/g/n/ac/ac Wave 2/ax
- Interface
- 1 X 10/100/1000 BASE-T Ethernet
- 1 X 2500 Base X Optical Ethernet SFP
- Radio Mode : 2×2 MU-MIMO with 2 spatial streams
- Mesh Support: Self-creating, Self-healing EasyMesh
- Maximum number of SSID: l6
- Maximum User Support 1024 clients per Access Point |(512 clients per radio)
- Power Supply IEEE 802.3at PoE/PoE+
- Power Consumption (Max) 17W (approx.)
- Max Transmit Power 30 dBm for 2.4 GHz, 30 dBm for 5 GHz (will depend on country-specific guidelines)
- Antenna Type Integrated directional antennas with 60°H & 15°V beamwidth
- Antenna Gain 14 dBi for 5 GHz, 14 dBi for 2.4 GHz
- Management Standalone (via GUI) or through on-premise based solution or cloud-based
- Enclosure Dimensions 374 x 217 x 87 mm or 14.7 x 8.5 x 3.43 inches
- Weight 1.82 Kg
- Operating Temperature 15°C to 60°C
- Certifications FCC Class A, CE, Passpoint 2.0, EasyMesh, WPA3, IP67, RoHS 3.0
Product Overview
Mounting of ion4x_2 Access Point
The ion4x_2 can be mounted on a pole or to a wall. Perform the following steps
for appropriate installation.
- Align L Plate with the holes at the back of Access Point
- Use the provided screws to fix the plate onto the Access Point.
The Access mounting Point bracket is fixed onto the mounting holes on the
Pole Mount
- Align the L Plate mounted Access Point with pole clamp &U-Bolt
- Pass the U-Bolt through the cuts of pole clamp & L Plate. Secure it in place with Hex Nuts.
- Access horizontal Point axis has the freedom of movement along with the vertical & horizontal axis
- The final alignment of Access Point on a pole mounting as shown below
Note: The pole mounting is designed for poles of diameter 40 mm to 60 mm. For mountings on larger size poles upto 140 mm, contact at [email protected]
Wall Mount
To mount the ion4x2 on a wall, use the wall mounting bracket, drywall screws, and screw anchors (* The entire wall mounting assembly is sold seperately).
- Take the reference from the wall mounting bracket and mark the position of the holes on the wall
- Use the drill machine to drill 2 holes on respective marked positions.
- Push the screw anchors into the holes with a hammer.
- Align the drilled holes with the holes of wall mounting bracket.
- Insert the drywall screws through the holes of mounting bracket into the wall.
- Wall mounting bracket is fixed to the wal.
- Mount the device on to the wall mounting bracket as discussed in Dole mountina process.
WARNING: HFCL is not held liable for any damages incurred during the process.
Getting the ion4x 2 Online
Step 1:
Power up
The Access Point can be powered up using PoE adaptor (48v) as shown below:
Note: Plug and Adaptor will vary by country/ region
Step 2:
Connect to the network
Section 1: Standalone AP
Follow the steps mentioned below and connect the Access Point to a network
- Connect an ethernet cable to the computer.
- Connect the other end of ethernet cable to the data port on PoE adapter (48V)
- Connect ion4x_2 PoE supported ethernet port to PoE adapter power port. Device will be powered on
- Configure the computer with a same domain static IP 192.168.1.X and a subnet mask of 255.255.255.0 (X is from 2 to 255)
- Open the web browser and enter the Access Point static IP address in the address bar: 192.168.1.1
- A login screen will appear
- Enter the default login credential details:
User- root, Password- hfcl!@ion
Section 2: Controller Managed AAP
Follow the steps mentioned below and connect the Acess Point to a network:
- Power-up the AP through PoE adapter or PoE switch
- Connect the AP to DHCP network and Internet
- Login to HFCL I0 cloud controller (cNMs) cnms.ionetworks.in with credentials provided
- Refer our website io.hfcl.com for detailed information to configure AP through cNMS
Step 3:
Check the LED status
LED Color | Status |
---|
Power LED Green
| Green color notifies the user that the device is powered ON
2.4 GHzStatus LED
| Solid blue color notifies the user that the 2.4 GHz radio is active and blinks while data is being transmitted on 2.4 GHzradio
5 GHzStatus LED
| Solid blue color notifies the user that the 5 GHzradio is active and blinks while data is being transmitted on 5 GHzradio
Safety Precautions
Observe the following safety precautions to avoid damage to the ion4x 2 Access Point:
- Do not power the device during installation
- Keep away from high voltage cables
- Do not power off the unit in the middle of an upgrade process
- The gland should be ground facing all the time
- Do not open the enclosure
- Fasten the device tightly
- Make sure the earthing wire is connected properly to the earthing points
Contact Us:
Email: [email protected]
Website: www.hfcl.com
www.io.hfcl.com
8, Commercial Complex, Masjid Moth, Greater Kailash-ll, New Delhi- 110048
HFCL Limited All Rights Reserved. 10 Networks and the 10 logo are registered
trademarks of HFCL Limited. Specifications are subject to change without
notice.