HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide User Guide

June 3, 2024
HFCL

HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide

HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital
Divide

Introduction

Thank you for choosing the IO’s Unlicensed Band Radio (UBR). Enterprise Grade point-to-point and point-to-multipoint solution is optimally designed to support low to medium capacity enterprise applications in unlicensed 5 GHz spectrum for short and long range links.

Packaging Content

HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide
1

ion412_CPE Specifications

Peak Throughput (aggregate)| Up to 300 Mbps Aggregate UUDL Throughput
MIMO| 2X2

Modulation

|

Upto256 QAM

Channel Bandwidth| 10/20/40 MHz
Wireless QoS| 802.lle WMM
Wireless Security| WPA, WPA2, & 128-bit AES-PSK with hardware

acceleration

Power Supply| IEEE 802.3af 24V Passive PoE
Power Consumption (Max)| <15W
Antenna Type| Integrated High Performance Antenna
Antenna Gain| 23 dBi
Management| Standalone (via GUI) or through appliance-based EMS or cloud-based
Enclosure Dimensions| 328 x 305 x 122 mm or 12.9 x 12 x 4.8 inches
Weight| 1.04 kg
Operating Temperature| o·c to ss·c
Certifications| CE, FCC Class A, RoHS 3.0, IP67

Product Overview

HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide
2

Mounting of ion412_CPE

The ion4I2…CPE can be mounted on a pole. Perform the following steps for appropriate installation.
Pole Mount
To mount ion4I2…CPE on a pole, use the pole holder & the hose clamp provided.

  1. Attach the pole holder to the backside of the CPE.
  2. The hose clamp is slided through the back of ion4I2_CPE as shown below.
  3. Wrap the hose clamps around the pole. Tighten the strap by turning the screws clockwise.

Getting the ion412_CPE Online

Step 1 : Power up
ion4I2_CPE can be powered up using PoE Injector (24V) as shown below:

HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide
6

Note: For powering on the CPE, use only HFCL PoE Injector supplied along with the unit. Plug and Adaptor will vary by country/ region.

Step 2: Login and Configure the CPE

Follow the steps mentioned below and connect CPE to a network :

  1. Connect ethernet cable to the laptop/ computer.
  2. Connect the other end of ethernet cable to the data port on PoE Injector.
  3. Connect CPE’s PoE supported ethernet port to PoE Injector power port. Device will get powered up.HFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide 7
  4. Open web browser and enter “CPE IP address” in the address bar. The default static IP address for 2×2 CPE is set to “192.168.1.1”.
  5. A login screen will appear.
  6. Enter the default login credential details: User- admin, Password- HFcl!@23#ionHFCL ion4l2-CPE Wi-Fi Solutions to Bridge Digital Divide 8
  7. Refer our user manual on our website io.hfcl.com for detailed information to configure CPE

Safety Precautions

Observe following safety precautions to avoid damage to the ion4I2_CPE :

  • Do not power the device during installation
  •  Do not subject the device to high temperatures
  • Keep away from high voltage cables
  • Do not power off the unit in the middle of an \v upgrade process
  • The gland should be ground facing all the time
  • Do not open the enclosure when the CPE is working
  • Fasten the device tightly

Contact Us:
Email: iosupport@hfcl.com
Website: www.hfcl.com
www.io.hfcl.com
8, Commercial Complex, Masjid Moth, Greater Kailash-11, New Delhi- 110048

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals