HFCL ion4ln Unlicensed Band Radio User Guide
- June 3, 2024
- HFCL
Table of Contents
ion4ln Unlicensed Band Radio
User Guide
ANYWHERE
EVERYWHERE
Introduction
Thank you for choosing the IO’s Unlicensed Band Radio (UBR). Enterprise Grade point-to-point and point-to-multipoint solution is optimally designed to support low to medium capacity enterprise applications in unlicensed 5 GHz spectrum for short and long range links.
Packaging Content
Mounting Kit
- Hood (1),
- M6 Hex Bolts with split washers (6)
- M6 Flange Nuts with serrations (4),
- M8 x 220 Bolts (2),
- Riveted U clamps (1),
- Pole clamp assembly (7 ),
- Pole clamp (1),
- Nuts M8 (4), M8 split washer (4) & M8 flat washers (4)
ion 414 Specifications
| Peak Throughput(aggregate) | Up to 700 Mbps Aggregate UL/DL Throughput |
|---|---|
| MIMO | 2X2 |
| Modulation | Upto 256 QAM |
| Channel Bandwidth | 10/20/40/80 MHz |
| Wireless QoS | 802 11e WMM |
| Wireless Security | WPA, WPA2, 8 128-bit AES-PSK with hardware acceleration |
| Power Supply | IEEE 802.3af Active PoE |
| Power Consumption (Max) | <15 W |
| GPS Location | GNSS-7 (GPS +GLONASS) |
| Antenna Type | Integrated High Performance Dish Antenna |
| Antenna Gain | 27 d8i |
| Management | Standalone (via GUI) or through appliance-based EMS or cloud-based |
| Enclosure Dimensions | 625x 625 x 280 mm or 24.6 x 24.6x 11 inches |
| Weight | 2 6 kg |
| Operating Temperature | 0Ct0 55C |
| Certifications | CE, FCC, ROHS 3 0, IP67 |
Product Overview
Installation Set-up
The 2 x 2 UBR with integrated dish antenna has four studs on its backside for
attaching the mounting bracket. The mounting bracket is designed in such a way
that UBR can be mounted on the pole with the help of its attaching parts. It
provides freedom of movement to the UBR for link alignment even after
mounting.
WARNING: Insecure mounting might damage the device or cause injury 10 by
HFCL is not responsible for damages incurred by insecure wall & pole mounting.
-
Use four M6 flange nuts and attach the hood with the UBR.
Refer to the image below:
Note: Make sure that the cut in the hood aligns
with lug connector. -
Attach pole clamp assembly with riveted U clamp with the help of three M6 hex bolts and split spring lock washers.
-
Mount this assembly from the previous step on UBR using three M6 hex bolts and split spring lock washers.
-
Once UBR is assembled, the next step is to mount on the pole using two M8 x 220 bolts and four split spring lock washers and flat washers.
-
Slightly loosen M6 bolts, rotate brackets to align the pointer mark, at an optimum angle to set the azimuth and elevation. Once the desired setting is attained, securely tighten the six bolts using a compatible spanner. Note: Angle marking for azimuth adjustment & elevation adjustment
Getting the ion 414 Online
Step 1: Power up
UBR can be powered up using PoE adaptor as shown below-
Note: For powering on UBR, only use HFCL POE adapter. Plug and Adaptor
will vary by country/ region.
Step 2: Login and Configure the UBR
Follow the steps mentioned below and connect UBR to a network
-
Connect Ethernet cable to the laptop/computer.
-
Connect the other end of Ethernet cable to the data port on PoE adapter.
-
Connect UBR’s PoE supported Ethernet port to PoE adapter power port. Device will be powered on.
-
Open web browser and enter “UBR IP address” in the address bar The default static IP address for 2 x 2 UBR is set to “192.168.11”
-
Alogin screen will appear
-
Enter the default login credential details.
User- admin, Password- HFcl!@23#ion
-
Refer our user manual on our website io.hfcl.com for detailed information to configure UBR
Step 3: Check the LED status
| LED Color | Status |
|---|
Green LED
(Power indication)| Green color notifies the user that the device is powered
ON
BLUE LED
(RSSL/Link indication)| Single blink: -1 to -50 dBm
Double blink: -51 to -60 dBm
Triple blink: Greater than -60 dBm
NOTE- If link is down, then link LED will be in continuous OFF state.
BLUE LED
(Alarm Indication)| Single blink: Minor Alarms
Double blink: Major Alarms
Triple blink: Critical Alarms
NOTE – During Reboot and Factory Reset, all the three LEDs will glow for 7 secs and the power LED will continue to glow
Safety Precautions
Observe following safety precautions to avoid damage to the ion 414 UBR
Do not power the device during installation
Do not subject the device to high temperatures
Keep away from high voltage cables
Do not power off the unit in the middle of an upgrade process
The gland should be ground facing all the time
Make sure the earthing wire is connected properly to the earthing points
Do not open the enclosure when the UBR is working
Fasten the device tightly
Contact Us:
Email: iosupport@hfcl.com
Website: www.hfcl.com
www.io.hfcl.com
8, Commercial Complex, Masjid Moth,
Greater Kailash-ll, New Delhi- 110048
Part Number QSG-02-0004
Revision. A
HFCL Limited All Rights Reserved. 10 Networks and the 10 logo are registered
trademarks of HFCL Limited.
Specifications are subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>