SWISHER FC15560BS, FC15560CL 60 Inch Fast Finish Trial Mower Owner’s Manual

June 3, 2024
Swisher

SWISHER FC15560BS, FC15560CL 60 Inch Fast Finish Trial Mower

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
PRO

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this manual When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death.

  • Read the manual. Learn to operate iliis machine safely.
  • Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to prevent accidental starting the engine when setting up, transporting, adjusting or making repairs.
  • Keep all shields and guards in place.
  • Understand the speed, steering and stability of this machine. Know the positions and operations of all controls before you operate iliis machine. Check all of the controls in a safe area before starting to work with this machine.
  • Allow only responsible adults who are familiar with these instructions to operate iliis machine. Never allow children to operate this machine.
  • Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and thrown by the blade.
  • Be sure the area is clear of other people before mowing. Be aware of the mower discharge direction and do not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Keep children llllder the watchful care of another responsible adult.
  • No riders!
  • Do not put hands OT feet near OT llllder rotating parts. Keep clear of the discharge opening at all times.
  • Do not mow in reverse. Always look down and behind before and while backing.
  • Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine.
  • Watch for traffic when operating near or crossing roadways.
  • Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary.
  • Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.
  • Do not operate the machine while under the influence of alcohol or drugs.
  • Operate self-propelled machines up and down slopes. There is significant risk of overturns when operating across slopes. Operate walk-behind machines across slopes. There is a significant risk of slipping under a walk-behind machine when operating up and down slopes. Do not operate on slopes greater than 15 degrees.
  • Never tamper with safety devices. Check their proper operation regularly.
  • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
  • Never make adjustments or repairs with the engine timing.

SAFETY DECALS

Replace decals immediately if damaged. Order by part number from Swisher.

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(1\)

REQUIRED ASSEMBLY

FRONT WHEEL CASTER ASSEMBLY

  1. Remove single nut and washers from caster shaft.
  2. Place one washer (NB195) on the shaft of the caster/wheel subassembly.
  3. Slide same shaft through the bearing/frame with wheel towards the ground.
  4. Place the other washer (NB195) on the shaft; it should be resting on the top bearing.
  5. Add thin washer (17×195).
  6. Thread nyloc jam nut onto shaft.
  7. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Over-tightening of this nut will bind caster.
  8. Repeat process for other front side.
  9. Push on plastic dust covers over nut and thin washer until it snaps into place.

REAR WHEEL ASSEMBLY

  1. Remove cotter pin from axle and remove thin washer (NB149) from axle. Leave two NB178 washers on axle.
  2. If necessary (to take up space) slide extra washer (NB178) over axle, then wheel (with valve stem out).
  3. Slide on washer (NB149) and replace cotter pin in end of axle.
  4. Bend cotter pin so it will not fall out.
  5. Repeat process for other wheel.

OFFSET & CENTER TOW HITCH BAR ASSEMBLY

  1. Lay out parts according to the diagram.
  2. Insert part 661A into part 662 and pin with the hitch pin (H11).
  3. Insert part 20954 into part 661A. Choose from the 3 holes to set the desired hitch length. Pin with a hitch pin (H11).
  4. Part 662 slides into the front tube of the frame. Again, choose from the 3 holes to arrange desired offset. Pin with a hitch pin (H11).
  5. Eliminate step 3 for hitching from the center bracket. Only one method can be used at a time.

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(2\)

Battery Mounting Detail

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(3\)

OPERATING YOUR TRAIL MOWER

The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended.
CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

INTENDED USE

This Trail Mower is designed to produce a quality finish cut on lawns, golf courses, etc. It is not designed to clear brush or cut saplings. Your Trail Mower should be towed behind an ATV, a golf cart, lawn tractor, or similar approved vehicle. It is not meant for speeds exceeding 5 mph.

ATTACIIlNG TRAIL MOWER TO TOW VEHICLE

  • Place mower behind vehicle and back vehicle up to desired attaching position.
  • When offsetting Trail Mower do so to side opposite the discharge of the tow vehicle.
  • Attach tow hitch (661) to the swivel hitch with hitch pin (HI 1). Make certain hitch pin goes completely through each piece and is clipped to prevent accidental separation.
  • Attach red safety tether (6736) to both the towing vehicle and to the Trail Mower toggle switch (685SP), located on the left battery side cover (17614). Its purpose is to manually stop mower engine or to stop mower engine in case the two machines become separated. (See Motor Base Detail page 14).
  • It is extremely important the safety tether is secured properly to both the toggle switch and the towing vehicle.

STARTING THE ENGINE
See engine manufacturer’s instructions for the type and amount of oil and fuel used. Trail Mowers with electric start engines will need a battery (sold separately). Swisher recommends using a standard “U I R” lawn & garden battery.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brushcovered, or grass-covered land. Other states or federal areas may have similar laws.

  • Engine must be level to accurately check and fill oil. Do not overfill.
  • Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged.
  • Check spark plug wire, oil, and fuel.
  • Check all electrical connections (See Schematics).
  • Make sure toggle switch is turned “ON’ and the red tether is properly attached.
  • Set engine idle to “CHOKE,, position.
  • With feet clear of mower deck, turn key switch to the “START,, position and release when engine begins to nm.
  • Set engine idle at desired RPM.

BREAKING IN YOUR MOWER

  • Set vehicle parking brake or chock wheels to prevent accidental rolling.
  • Start engine properly.
  • Slowly, engage blade control.
  • In a safe environment, i.e. no children, allow blades to rotate and engine to idle for 5 minutes. This breaks in the belts and the engine.
  • Stop mower properly.

STARTING TO MOW

  • Adjust the cutting height.
  • Double check vehicle to mower attachment.
  • Start mower engine properly.
  • Slowly, activate the blade engage lever (21929) by rotating it forward and left until the lever locks into place.
  • Carefully mount tow vehicle and start mowing slowly.

STOPPING THE MOWING SESSION

  • Pull safety tether to shut toggle switch “OFF,,_ If the engine fails to stop or if the safety tether has become inoperable, then use Alternative Stopping Method.

ALTERNATIVE STOPPING METHOD

  • Bring vehicle to complete stop, shut off engine, and set parking brake.
  • Disengage blade engage lever (21929).
  • Manually shut toggle and key switches to their “OFF” positions.
  • Always remember to remove keys to avoid irresponsible usage.

TRANSPORTING MOWER

  • Stop mower properly.
  • Place mower deck in its highest position.
  • If transporting without the use of a tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.

SUGGESTED MOWING PRACTICES

  • Operate mower engine at full throttle to assure the best cutting performance and maximum material discharge.
  • Allow wet grass to dry. Clumps of wet grass will collect under the mowing deck.
  • Mowing should be started with tow vehicle in low gear and increased only as safe mowing conditions permit. This speed should not exceed 5 mph.
  • The average lawn should be cut to approximately 2.5″ during the cool season and to over 3″ during the hot months.
  • For a healthier lawn and better aesthetics, your lawn should be mowed often and after moderate growth.
  • When cutting high or dense grass areas go slowly. Some areas may need to be mowed twice. The second cut should be at 90 degrees to the frrst, if possible.
  • Mowing thick or high grass. Raise rear height crank handles to .5″-.75″ above the other two handles.
  • Creating a manicured lawn. Lower rear height crank handle to .25″ -.5″ below front of deck. This allows grass blades to be cut twice. It also continually cuts clippings to produce a mulching effect.

GENERAL TROUBLESHOOTING

  • The mower is not cutting level.
    • Level deck, making sure the side crank-handles are equal.
    • Check air pressure of all tires; make sure they are equal, and to manufactures specifications.
    • Examine blades for damage, while mower engine is not running.
  • The engine will not start.
    • Disengage blades, turn toggle switch to “ON” position, check battery and all other electrical connections, and inspect spark plug and wire.
    • Check for fuel in the engine.
  • Engine runs poorly.
    • See engine manual.
    • Check throttle adjuster.
    • Replace fuel, clean fuel filter and fuel line.

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS
The warranty on this Trail Mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. Periodically inspect and clean excessive debris inside the battery cover (17340) and belt covers (6025). Disconnect spaik: plug wire before cleaning.

BEFORE EACH USE

  • Check engine oil level on a level surface. Check twice to insure an accurate reading.
  • Check condition of air filter; clean and replace as necessary.
  • Check blade operation; keep blades in good condition.
  • Check for loose fasteners and tighten them as needed.

AFfER EACH USE

  • Keep blades sharp.
  • Remove fresh grass clippings with garden hose.
  • Grass clippings hardened to the underside should be scraped out with a putty knife.
  • Keep fluids at proper levels.
  • Cover unit to prevent rain or other debris buildup. Definitely cover the engine.

BEFORE AND/ORAFfER EACH SEASON

  • Replace the spark plug.
  • Clean or replace the air filter.
  • A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.
  • Check blades and belts for wear. Replace as necessary.

STORAGE RECOMMENDATIONS

CAUTION! Do not store engine indoors or another poorly ventilated area. Keep engine away from gas appliances where fumes could contact open flame, pilot lights, or sparks.
If engine is to be stored for 30 or more days, prepare unit as follows:

  • Drain fuel outside into an approved container.
  • Start engine properly and run until unit is out of fuel.
  • Let engine cool.
  • Remove remaining gasoline from carburetor and fuel tank to prevent gum deposits from forming within the engine. Gum deposits can cause malfunction in the engine.
  • Store mower with blades disengaged to prevent belts from being permanently stretched.

BLADE CARE AND SERVICE
For best results cutter blades must be kept shaip. The blades can be shaipened with a few strokes of a file or grinding wheel. Do not attempt to shaipen blades while they are on the mower. Disconnect spark plug wire before servicing unit
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight.

FRAME ASSEMBLY

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(4\)

ITEM #| QTY.| PART NO.| DESCRIPTION| ITEM #| QTY.| PART NO.| DESCRIPTION
---|---|---|---|---|---|---|---
1| 1| 662| Weldment – Tongue Offset Extension| 10| 3| 10579| Bushing -Stepped Height Adjust
2| 1| 661A
| Weldment – Solid Stock Hitch| 11| 6| NB126| Pin – 1/8″ X 1″ Cotter
3| 4| H11| Pin – Safety Hit ch| 12| 4| T2PB| Bushing – Plastic
4| 2| NB622| Bolt – Serr Flange, 5/16-18X2 1/4| 13| 3| 10038| Bolt – Eye
5| 1| 21152| Plate – Clevis, Top| 14| 1| 3665| Bar – Left Sway
6| 1| 20953
| Tube – Tow Hitch| 15| 1| 17600| Weldment – T60 Frame
7| 1| 21153
| Plate – Clevis, Bottom| 16| 4| NB178| Washer – 5/8 ID X 1 OD 10 GA
8| 2| NB170| Nut – Serr Flange 5/16-18| 17| 2| F4157WK| Wheel/Tire
9| 1| 3664| Bar – Right Sway| 18| 2| NB149| Washer – 5/8 ID X 1 OD 14 GA

GAS TANK ASSEMBLY DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(5\)

Item # Qty Description Part #
1 4 Nut – Nyloc 3/8-16 ZY NB182
2 1 Mount – For EPA/CARB Gas Tank 18331*
3 2 Ubolt – SQ , 3/8-16X2.437 X 3 Lg GR 5 ZY 12447
4 1 Cap, Fuel – 2.50 Gallon, Carb Sealed 18221
5 1 Bracket – Fuel Tank 18225
6 2 Bolt – Serr Flange 1/4-20 X 1 3/4 GR5 ZY 18236
7 1 Fuel Tank – 2.5 Gallon, Carb 18214
8 2 Washer – SAE Flat 1/4 ZY NB274
9 2 Nut – Nylock 1/4-20 NB180

CENTER BLADE DRIVER DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(6\)

ITEM # QTY. PART # DESCRIPTION
1 1 NB175 Nut – Jam 3/4-16 Grade 2
2 1 AS155 Washer – Belleville1.5 X .761 X .098
3 1 21893 Pulley – Blade, 5.5″ A/B
4 1 6065PM Spacer – 3/4 ID X 1-1/2
5 1 20651 Pulley – 5″
6 3 NB179 Washer – 3/4 ID X 1 1/4 OD 18 Ga
7 2 B98 Bearing
8 4 NB690 Bolt – Serrtd Flange 1/4-20 X 3/4 Gr 5
9 1 9057* Housing – Bearing
10 4 NB524 Nut – Flange1/4-20
11 1 9054 Shaft – Center 5.75″
12 1 B98W Washer – Flat 3/4 ID X 1 3/4 OD
13 2 NB216 Nut – Lock, Two Way 3/8-24 ZY Gr A
14 1 9008 Plate – Blade Mount
15 1 20186 Blade – G6 Gator, 20.5″
16 1 NB607 Washer – SP Bellvl. Pln. .413 X.945 X.118
17 2 NB166 Bolt – 3/8-24 X 1 1/4 HCC GR5 ZY
18 1 NB238N Bolt – HHC 3/8-24 X 1 Grade 5 Locktite

Recommended Torque Specifications

Part No. Torque (ft-lbs)
NB175 90
NB238N 35
NB524 20
NB216 35

Blade Driver Assembly
(Includes shaft, housing and bearings) Part # 9058, 5.75” Shaft (Center) Part

9018, 4.25” Shaft (Outer)

OUTER BLADE DRIVER DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(7\)

ITEM # QTY. PART # DESCRIPTION
1 1 NB175 Nut – Jam 3/4-16
2 1 AS155 Washer – Bellville 1.5 X .761 X .098
3 1 20651 Pulley – 5″
4 3 NB179 Washer – 3/4 ID X 1 1/4 OD 18 Ga
5 2 B98 Bearing
6 4 NB690 Bolt – Serr Flange 1/4-20 X 3/4 Grade 5
7 1 9057* Housing – Bearing
8 4 NB524 Nut – Flange 1/4-20
9 1 9076 Shaft – L & R 4.25″
10 1 B98W Washer – Flat 3/4 ID X 1 3/4 OD
11 2 NB216 Nut – Lock, Two Way 3/8-24 ZY Gr A
12 1 9008 Plate – Blade Mount
13 1 20186 Blade – G6 Gator 20 1/2″
14 1 NB607 Washer – SP Bellvl. PLN .413 X.945 X.118
15 2 NB166 Bolt – 3/8-24 X 1 1/4 HCC GR5 ZY
16 1 NB238N Bolt – HHC 3/8-24 X 1 Gr 5 Locktite

MOWER DECK DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(8\)

ITEM # QTY PART NO DESCRIPTION
1 2 18391 Cover – Belt, Black Composite
2 8 18531 Washer – Bent .25″ ID X 18GA
3 8 NB703 Screw – MSC, 10-24 X 1 1/4
4 8 18532 Nut – Clip, 10-24
5 1 See Grass Chute Asy Detail
6 2 NB577 Bolt -1/2-13 X 3 1/2
7 3 3511 Wheel – Gauge
8 4 NB121 Nut – Jam Lock 1/2-13 2-Way
9 1 15780* Bracket – Wheel Right
10 17 NB170 Nut – Serr Flange 5/16-18 Z
11 9 NB596 Bolt – Serr Flange 5/16-18 X 3/4
12 1 18383* Bracket – Middle Roller
13 1 NB688 Nut – Nyloc Jam, 1/2-13 ZY
14 1 NB132 Bolt -1/2-13 X 4 HCC
15 1 NB281 Nut – Nyloc 1/2-13 ZY
16 1 See Engage Lever Detail
17 2 T2PB Bushing – Plastic
18 1 18384* Bracket – Deck Hanger
19 1 NB509 Bolt – 1/2-13 X 2 HCC
20 1 15779* Bracket – Left Wheel
21 9 26X249 Screw – .312-18X.75
22 1 NB707 Bolt – Carriage 3/8-16X4
23 2 AS001 Roller – Anti-Scalp 3/8 ID
24 1 NB207 Nut – Nyloc 3/8-16
25 1 21096* Shield – Debris
26 1 18382* Weldment – Deck
27 2 NB106 Bolt – 5/16-18 X 2 3/4 HCC
28 2 NB181 Nut – Nyloc 5/16-18
29 1 See Center Blade Driver Detail
30 1 See Motor Base Detail
31 1 See Safety Switch Bracket Detail
32 1 See Idler Detail
33 2 See Outer Blade Driver Detail

GRASS CHUTE ASSEMBLY DETAIL

ITEM # QTY PART NO DESCRIPTION
1 1 18702* Weldment – Grass Chute
2 7 10501 Bolt – Carriage 3/8-16 X 1 1/4
3 1 18604 Rubber – Grass Chute
4 7 NB272 Washer – SAE Flat 3/8
5 7 NB182 Nut – Nyloc 3/8-16
6 1 18652* Bracket – Grass Chute
7 2 26X249 Screw – .312-18 X .75
8 1 18654* Bracket – Grass Chute Mount
9 1 18595 Rod – Deck, Grass Chute
10 1 166X34 Spring – Torsion
11 2 NB117 Nut – Push, 5/16

CASTER / WHEEL ASSEMBLY DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(10\)

MOTOR BASE DETAIL

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(12\)

ITEM #| QTY.| PART NO.| DESCRIPTION| ITEM #| QTY.| PART NO.| DESCRIPTION
---|---|---|---|---|---|---|---
1| 10| 024206| Screw – 12 X 1/2 Hex Self Tap| 28| 1| 10636YZ| Bolt – Spade, 5/16-18 X12
2| 1| 17840| Cover – Battery Top| 29| 1| NB210Z| Nut – 5/16-18 HNC
3| 2| NB197| Screw – Phillips Truss 8-32 X 1/2| 30| 2| NB181| Nut – Nyloc 5/16-18
4| 1| 17898| Cable – Throttle; T60| 31| 1| NB280| Nut – 2 Way Lock 3/8-16 Wax Gr A
5| 2| NB201| Nut – Kep 8-32| 32| 1| B527| Pulley – Idler, OD-3.25″, ID-3/8″
6| 1| 17616
| Cover – Battery Right| 33| 1| NB272| Washer – SAE Flat 3/8 ZY Carbon Steel
7| 1| 17614| Cover – Battery Top Front| 34| 1| NB107| Bolt – 3/8-16 X 1 1/2 HCC GR5
8| 1| 9087| Nut – Key Switch| 35| 1| 11158| Nut – Jam, Nyloc 5/16-18
9| 1| 9088| Washer – Lock, Key Switch| 36| 1| NB203| Nut – Kep 1/4-20
10| 1| 685SP| Switch – Toggle, Single Pole| 37| 1| 16000| Valve – Oil Drain
11| 1| 3623| Switch – Key| 38| 1| 9031| Key Stock – 1/4 X 1 Undr Size
12| 1| 17615
| Cover – Battery Left| 39| 1| 688| Pulley – Engine, 5.5″
13| 6| NB161| Screw – HX Tek 1/4 X 3/4 ZP| 40| 1| 689S| Spacer – Short, Engine Pulley, .687
14| 2| 17760| Bolt-L| 41| 1| TR150W| Washer – .531IDX1 1/2ODX.062(Ht Trtd)
15| 2| NB524| Nut – Serr Flange, 1/4-20 Grade 5| 42| 2| 699| Washer – Belleville 7/16 X 1 1/4
16| 1| 14869| Guide – Belt; T60| 43| 1| NB452N| Bolt – 7/16-20 X 1 HCF GR5 Nylock
17| 4| NB275| Washer – SAE Flat 5/16| 44| 2| NB114| Bolt – TCS 1/4-20 X 1/2
18| 2| NB250| Bolt – 1/4-20 X 3/4 GR5| 45| 1| 1002004| Solenoid – 3 Pole
19| 2| NB253| Bolt – Serr Flange, 5/16-18 X1 1/4 Gr5| 46| 1| NB182| Nut – Nyloc 3/8-16
20| 4| NB170| Nut – Serr Flange 5/16-18 Case Hrd| 47| 1| —| See Saftey Switch Detail
21| 1| N/A| Engine (Reference Model Shown)| 48| 1| 6009| Idler – Engage Weldment
22| 1| 689L| Spacer – Long, Engine Pulley, 1.5″| 49| 1| NB172| Nut – Kep 10-24 ZY
23| 1| 18387
| Motor Base – Weldment| 50| 1| 21894| Eyebolt – 10-24 X 1 3/8, w/ Nut
24| 2| NB180| Nut – Nyloc 1/4-20| 51| 1| BRS6| Spring
25| 1| 17794*| Bracket – Battery Hold Down| 52| 1| NB596| Bolt – Serr Flange, 5/16-18 X 3/4
26| 1| 6000| Guide – Belt| 53| 1| 4422| Spring – Idler Tension, Bent Leg
27| 2| NB515| Bolt – Serr Flange,5/16-18 X1 3/4 Gr5| 54| 1| NB220| Bolt – Shlder, 1/2 X 1-9/16 W3/4 Gr2 ZY

Engage Lever Detail

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(13\)

Height Adjust Handle Detail

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(14\)

Safety Switch & Bracket Detail

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(15\)

6055 Idler Detail

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(16\)

ITEM # QTY. PART # DESCRIPTION
1 1 NB618 Bolt – 3/8-16 X 1 1/4 GR5
2 1 6040Z Washer – Idler
3 1 6054* Idler – Bottom
4 1 6037 Bushing – Idler
5 1 NB182 Nut – Nyloc 3/8-16
6 2 NB181 Nut – Nyloc 5/16-18
7 1 NB280 Nut – 2 Way Lock 3/8-16 Gr A
8 2 NB272 Washer – SAE Flat 3/8
9 1 B527 Pulley – Idler, OD-3.25″, ID-3/8″
10 1 21425 Spring – Extension
11 1 NB170 Nut – Serr Flange 5/16-18
12 1 NB501 Bolt – 5/16-18 X 1 GR5
13 1 NB107 Bolt – 3/8-16 X 1 1/2 GR5
14 1 NB315 Eyebolt – 5/16-18 X 3 w/Gap
15 1 NB173 Nut – Jam 5/16-18

Belt Configuration

SWISHER-FC15560BS-FC15560CL-60-Inch-Fast-Finish-Trial-Mower-
\(17\)

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. As required by CFR § 1060.120, the fuel system related components, which have been certified to this equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions:

  1. Engine Warranty All engines utilized on our products has a separate warranty extended to them by the individual engine manufacturer. Any engine service difficulty is the responsibility of the engine manufacturer and in no way is Swisher or its agents responsible for the engine warranty. The Briggs & Stratton Engine Service Hot Line is 1-800-233-3723.
  2. Commercial Use This product is not intended for commercial use and carries no commercial warranty.
  3. Limitations This warranty applies only to products, which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of the product.
  4. Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

HOW TO ORDER REPAIR PARTS

Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found at the left rear of the unit on the belt cover skirt. The model number for the engine will be found on the top of the blower fan housing. All mower parts listed herein may be ordered directly from Swisher or your nearest Swisher dealer. All engine parts may be ordered from the nearest dealer of the engine supplied with your mower. Color cannot be guaranteed on service parts.

WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INFORMATION AVAILABLE:

  • PRODUCT – FC60 FAST FINISH TRAIL MOWER
  • SERIAL NUMBER – ___
  • MODEL NUMBER – ___
  • ENGINE MODEL NUMBER – ___
    • TYPE – ___
  • PART NUMBER
  • PART DESCRIPTION

TELEPHONE – 1-800-222-8183
FAX – 1-660-747-8650
SWISHER ACQUISITION INC.
1602 CORPORATE DRIVE
WARRENSBURG, MO 64093
www.swisherinc.com

SWISHER ACQUISITION INC.
1602 CORPORATE DRIVE., WARRENSBURG MO 64093
PHONE 800-222-8183
FAX 660-747-8650
EMAIL CustomerCare@SwisherInc.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals