SWISHER FC14560BS 60” Fast Finish Trail Mower Owner’s Manual

June 7, 2024
Swisher

FC14560BS 60” Fast Finish Trail Mower

www.swisherinc.com
OWNER’S MANUAL
STARTING SERIAL #: L118-335001
MODEL NO.
FC14560BS FC14560BS-CA
FC14560CL FC14560CL-CA

60″ FAST FINISH TRAIL MOWER

IMPORTANT

Read and follow all Safety Precautions and Instructions before operating this
equipment.

Assembly Operation Service and Adjustment Repair Parts

SWISHER ACQUISITION INC. 1602 CORPORATE DRIVE., WARRENSBURG MO 64093 PHONE 800-222-8183 FAX 660-747-8650 EMAIL CustomerCare@SwisherInc.com
10/1/2019

18028 REV 18-335

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser.
As required by CFR § 1060.120, the fuel system related components, which have been certified to this equipment by SAI are to be free of defects in material and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser.
We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions:

1) Engine Warranty
All engines utilized on our products has a separate warranty extended to them by the individual engine manufacturer. Any engine service difficulty is the responsibility of the engine manufacturer and in no way is Swisher or its agents responsible for the engine warranty. The Briggs & Stratton Engine Service Hot Line is 1-800-233-3723.

2) Commercial Use
This product is not intended for commercial use and carries no commercial warranty.

3) Limitations
This warranty applies only to products, which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of the product.

4) Exclusions
Excluded from this warranty are normal wear, normal adjustments, and normal maintenance. In the event you have a claim under this warranty, you must return the product to an authorized service dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death.

  • Read the manual. Learn to operate this machine safely.
  • Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to prevent accidental starting the engine when setting up, transporting, adjusting or making repairs.
  • Keep all shields and guards in place.
  • Understand the speed, steering and stability of this machine. Know the positions and operations of all controls before you operate this machine. Check all of the controls in a safe area before starting to work with this machine.
  • Allow only responsible adults who are familiar with these instructions to operate this machine. Never allow children to operate this machine.
  • Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and thrown by the blade.
  • Be sure the area is clear of other people before mowing. Be aware of the mower discharge direction and do not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Keep children under the watchful care of another responsible adult.
  • No riders!
  • Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
  • Do not mow in reverse. Always look down and behind before and while backing.
  • Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine.
  • Watch for traffic when operating near or crossing roadways.
  • Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary.
  • Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.
  • Do not operate the machine while under the influence of alcohol or drugs.
  • Operate self-propelled machines up and down slopes. There is significant risk of overturns when operating across slopes. Operate walk-behind machines across slopes. There is a significant risk of slipping under a walk-behind machine when operating up and down slopes. Do not operate on slopes greater than 15 degrees.
  • Never tamper with safety devices. Check their proper operation regularly.
  • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
  • Never make adjustments or repairs with the engine running.
SAFETY DECALS

Replace decals immediately if damaged. Order by part number from Swisher.

OD11- No step Decal

OD45- Warning Decal

OD55- Triangle Danger Decal

OD43- Flying Debris Decal

OD33- Speed Decal

OD29- Danger Decal

REQUIRED ASSEMBLY

FRONT WHEEL CASTER ASSEMBLY

  1. Remove single nut and washers from caster shaft.
  2. Place one washer (NB195) on the shaft of the caster/wheel subassembly.
  3. Slide same shaft through the bearing/frame with wheel towards the ground.
  4. Place the other washer (NB195) on the shaft; it should be resting on the top bearing.
  5. Add thin washer (17×195).
  6. Thread nyloc jam nut onto shaft.
  7. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Over-tightening of this nut will bind caster.
  8. Repeat process for other front side.
  9. Push on plastic dust covers over nut and thin washer until it snaps into place.
REAR WHEEL ASSEMBLY
  1. Remove cotter pin from axle and remove thin washer (NB149) from axle. Leave two NB178 washers on axle.
  2. If necessary (to take up space) slide extra washer (NB178) over axle, then wheel (with valve stem out).
  3. Slide on washer (NB149) and replace cotter pin in end of axle.
  4. Bend cotter pin so it will not fall out. 5. Repeat process for other wheel.
OFFSET & CENTER TOW HITCH BAR ASSEMBLY
  1. Lay out parts according to the diagram.
  2. Insert part 661A into part 662 and pin with the hitch pin (H11).
  3. Insert part 20954 into part 661A. Choose from the 3 holes to set the desired hitch length. Pin with a hitch pin (H11).
  4. Part 662 slides into the front tube of the frame. Again, choose from the 3 holes to arrange desired offset. Pin with a hitch pin (H11).
  5. Eliminate step 3 for hitching from the center bracket. Only one method can be used at a time.

center

A U1 battery is required (not included). Position battery hold down bracket as shown. Tighten nuts so battery will not shift position.
*Battery cover not shown

battery mounting

OPERATING YOUR TRAIL MOWER

The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine.
The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended.
CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
INTENDED USE This Trail Mower is designed to produce a quality finish cut on lawns, golf courses, etc. It is not designed to clear brush or cut saplings. Your Trail Mower should be towed behind an ATV, a golf cart, lawn tractor, or similar approved vehicle. It is not meant for speeds exceeding 5 mph.

ATTACHING TRAIL MOWER TO TOW VEHICLE

  • Place mower behind vehicle and back vehicle up to desired attaching position.
  • When offsetting Trail Mower do so to side opposite the discharge of the tow vehicle.
  • Attach tow hitch (661) to the swivel hitch with hitch pin (H11). Make certain hitch pin goes completely through each piece and is clipped to prevent accidental separation.
  • Attach red safety tether (6736) to both the towing vehicle and to the Trail Mower toggle switch (685SP), located on the left battery side cover (17614). Its purpose is to manually stop mower engine or to stop mower engine in case the two machines become separated. (See Motor Base Detail page 14).
  • It is extremely important the safety tether is secured properly to both the toggle switch and the towing vehicle.
STARTING THE ENGINE

See engine manufacturer’s instructions for the type and amount of oil and fuel used. Trail Mowers with electric start engines will need a battery (sold separately). Swisher recommends using a standard “U 1 R” lawn & garden battery.
IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

  • Engine must be level to accurately check and fill oil. Do not overfill.

  • Make sure the tow vehicle parking brake is set, mower is level, and blades are disengaged.

  • Check spark plug wire, oil, and fuel.

  • Check all electrical connections (See Schematics).

  • Make sure toggle switch is turned “ON” and the red tether is properly attached.

  • Set engine idle to “CHOKE” position.

  • With feet clear of mower deck, turn key switch to the “START” position and release when
    engine begins to run.

  • Set engine idle at desired RPM.

BREAKING IN YOUR MOWER
  • Set vehicle parking brake or chock wheels to prevent accidental rolling.
  • Start engine properly.
  • Slowly, engage blade control.
  • In a safe environment, i.e. no children, allow blades to rotate and engine to idle for 5 minutes. This breaks in the belts and the engine.
  • Stop mower properly.

CAUTION! SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.

MOWER HEIGHT ADJUSTMENT
  • Adjust while mower is not running.
  • The cutting range is approximately 1.5″ to 4.5″. The height has been measured from the ground to the blade tip without the engine running.
  • Rotate height adjust crank handles (H7N) in a clockwise direction to lift the mower deck. A counter-clockwise direction is used to lower the mower deck.
  • Make sure the height adjustment is the same at side crank handles. For best results, see “SUGGESTED PRACTICE” section. Graduated scales are for reference only, not the actual cutter height.
  • Place crank handle in a retracted position to maintain height adjustment.
STARTING TO MOW
  • Adjust the cutting height.
  • Double check vehicle to mower attachment.
  • Start mower engine properly.
  • Slowly, activate the blade engage lever (21929) by rotating it forward and left until the lever locks into place.
  • Carefully mount tow vehicle and start mowing slowly.
STOPPING THE MOWING SESSION
  • Pull safety tether to shut toggle switch “OFF”. If the engine fails to stop or if the safety tether has become inoperable, then use Alternative Stopping Method.
ALTERNATIVE STOPPING METHOD
  • Bring vehicle to complete stop, shut off engine, and set parking brake.
  • Disengage blade engage lever (21929).
  • Manually shut toggle and key switches to their “OFF” positions.
  • Always remember to remove keys to avoid irresponsible usage.
TRANSPORTING MOWER
  • Stop mower properly.
  • Place mower deck in its highest position.
  • If transporting without the use of a tow vehicle, then remove spark plug wire and place where it cannot contact the spark plug.
SUGGESTED MOWING PRACTICES
  • Operate mower engine at full throttle to assure the best cutting performance and maximum material discharge.
  • Allow wet grass to dry. Clumps of wet grass will collect under the mowing deck.
  • Mowing should be started with tow vehicle in low gear and increased only as safe mowing conditions permit. This speed should not exceed 5 mph.
  • The average lawn should be cut to approximately 2.5″ during the cool season and to over 3″ during the hot months.
  • For a healthier lawn and better aesthetics, your lawn should be mowed often and after moderate growth.
  • When cutting high or dense grass areas go slowly. Some areas may need to be mowed twice. The second cut shouldbe at 90 degrees to the first, if possible.
  • Mowing thick or high grass. Raise rear height crank handles to .5″-.75″ above the other two handles.
  • Creating a manicured lawn. Lower rear height crank handle to .25″-.5″ below front of deck. This allows grass blades to be cut twice. It also continually cuts clippings to produce a mulching effect.
GENERAL TROUBLE SHOOTING
  • The mower is not cutting level.
    o Level deck, making sure the side crank-handles are equal.
    o Check air pressure of all tires; make sure they are equal, and to manufactures specifications.
    o Examine blades for damage, while mower engine is not running.

  • The engine will not start.
    o Disengage blades, turn toggle switch to “ON” position, check battery and all other electrical connections, and inspect spark plug and wire.
    o Check for fuel in the engine.

  • Engine runs poorly. o See engine manual.
    o Check throttle adjuster. o Replace fuel, clean fuel filter and fuel line.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER PROBLEMS.

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this Trail Mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. All adjustments in this manual should be checked at least once each season. Periodically inspect and clean excessive debris inside the battery cover (17340) and belt covers (6025). Disconnect spark plug wire before cleaning.

BEFORE EACH USE
  • Check engine oil level on a level surface. Check twice to insure an accurate reading.
  • Check condition of air filter; clean and replace as necessary.
  • Check blade operation; keep blades in good condition.
  • Check for loose fasteners and tighten them as needed.
AFTER EACH USE
  • Keep blades sharp.
  • Remove fresh grass clippings with garden hose.
  • Grass clippings hardened to the underside should be scraped out with a putty knife.
  • Keep fluids at proper levels.
  • Cover unit to prevent rain or other debris buildup. Definitely cover the engine.
BEFORE AND/OR AFTER EACH SEASON
  • Replace the spark plug.
  • Clean or replace the air filter.
  • A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.
  • Check blades and belts for wear. Replace as necessary.
STORAGE RECOMMENDATIONS CAUTION!

Do not store engine indoors or other poorly ventilated area. Keep engine away from gas appliances where fumes could contact open flame, pilot lights, or sparks. If engine is to be stored for 30 or more days, prepare unit as follows:

  • Drain fuel outside into an approved container.
  • Start engine properly and run until unit is out of fuel.
  • Let engine cool.
  • Remove remaining gasoline from carburetor and fuel tank to prevent gum deposits from forming within the engine. Gum deposits can cause malfunction in the engine.
  • Store mower with blades disengaged to prevent belts from being permanently stretched.
BLADE CARE AND SERVICE

For best results cutter blades must be kept sharp. The blades can be sharpened with a few strokes of a file or grinding wheel. Do not attempt to sharpen blades while they are on the mower. Disconnect spark plug wire before servicing unit. Important: Replace blades that have been damaged or deeply nicked. Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight.

Only a qualified mechanic should be used for any adjustments, disassembly or other kind of repairs.

FRAME ASSEMBLY
ITEM # QTY PART NO. DESCRIPTION
1 1 662*

Weldment – Tongue Offset Extension

2| 1| 661A*|

Weldment – Solid Stock Hitch

3| 4| H11|

Pin – Safety Hitch

4| 2| NB622|

Bolt – Serr Flange, 5/16-18X2 1/4

5| 1| 21152*|

Plate – Clevis, Top

6| 1| 20953*|

Tube – Tow Hitch

7| 1| 21153*|

Plate – Clevis, Bot tom

8| 2| NB170|

Nut – Serr Flange 5/16-18

9| 1| 3664|

Bar – Right Sway

ITEM # QTY. PART NO. DESCRIPTION
10 3 10579

Bushing -Stepped Height Adjust

11| 6| NB126|

Pin – 1/8″ X 1″ Cotter

12| 4| T2PB| Bushing – Plastic
13| 3| 10038| Bolt – Eye
14| 1| 3665| Bar – Left Sway
15| 1| 17600*|

Weldment – T60 Frame

16| 4| NB178|

Washer – 5/8 ID X 1 OD 10 GA

17| 2| F4157WK| Wheel/Tire
18| 2| NB149|

Washer – 5/8 ID X 1 OD 14 GA

GAS TANK ASSEMBLY DETAIL

Parts Not Shown


Part #

|

Description

11782

|

 Line – Fuel, Bulk, 1/4″ Low Perm

18232

|

 Line – Fuel, Bulk, 3/16″ Low Perm

18223

|

Clamp – Fuel Line

AS021

|

Tie, Black 5 1/2″

Item #

|

 Qty

|

Description

|

Part #

---|---|---|---

1

|

 4

|

Nut – Nyloc 3/8-16 ZY

|

NB182

2

|

 1

|

 Mount – For EPA/CARB Gas Tank

|

 18331*

3

|

 2

|

 Ubolt – SQ , 3/8-16X2.437 X 3 Lg GR 5 ZY

|

 12447

4

|

 1

|

 Cap, Fuel – 2.50 Gallon, Carb Sealed

|

 18221

5

|

 1

|

Bracket – Fuel Tank

|

18225

6

|

 2

|

 Bolt – Serr Flange 1/4-20 X 1 3/4 GR5 ZY

|

 18236

7

|

 1

|

 Fuel Tank – 2.5 Gallon, Carb

|

 18214

8

|

 2

|

Washer – SAE Flat 1/4 ZY

|

NB274

9

|

 2

|

Nut – Nylock 1/4-20

|

NB180

ONLY INCLUDED ON “CA” MODELS (CALIFORNIA COMPLIANT)

Item #

|

 Qty

|

Description

|

Part #

---|---|---|---

1

|

 4

|

 Screw – 10-24 X 3/4 Phil Truss Head ZP

|

 024203

2

|

 2

|

 Bracket – Carbon Canister, ZT

|

 17127

3

|

 4

|

Nut – 10-24 Nylon Lock

|

024900

4

|

 1

|

 Carbon Canister – 2.50 Gallon, 3/16 Line

|

 18224

5

|

 2

|

 Cable Tie – Carbon Canister

|

 18219

CENTER BLADE DRIVER DETAIL

ITEM #

|

 QTY.

|

 PART #

|

DESCRIPTION

---|---|---|---

1

|

 1

|

 NB175

|

 Nut – Jam 3/4-16 Grade 2

2

|

 1

|

 AS155

|

 Washer – Belleville1.5 X .761 X .098

3

|

 1

|

 21893

|

Pulley – Blade, 5.5″ A/B

4

|

 1

|

 6065PM

|

 Spacer – 3/4 ID X 1-1/2

5

|

 1

|

 20651

|

Pulley – 5″

6

|

 3

|

 NB179

|

 Washer – 3/4 ID X 1 1/4 OD 18 Ga

7

|

 2

|

 B98

|

Bearing

8

|

 4

|

 NB690

|

 Bolt – Serrtd Flange 1/4-20 X 3/4 Gr 5

9

|

 1

|

 9057*

|

Housing – Bearing

10

|

 4

|

 NB524

|

Nut – Flange1/4-20

11

|

 1

|

 9054

|

Shaft – Center 5.75″

12

|

 1

|

 B98W

|

 Washer – Flat 3/4 ID X 1 3/4 OD

13

|

 2

|

 NB216

|

 Nut – Lock, Two Way 3/8-24 ZY Gr A

14

|

 1

|

 9008

|

Plate – Blade Mount

15

|

 1

|

 20186

|

Blade – G6 Gator, 20.5″

16

|

 1

|

 NB607

|

 Washer – SP Bellvl. Pln. .413 X.945 X.118

17

|

 2

|

 NB166

|

 Bolt – 3/8-24 X 1 1/4 HCC GR5 ZY

18

|

 1

|

 NB238N

|

 Bolt – HHC 3/8-24 X 1 Grade 5 Locktite

Recommended Torque Specifications


Part No.

|

 Torque (ft-lbs)

NB175

|

 90

NB238N

|

 35

NB524

|

 20

NB216

|

 35

Blade Driver Assembly
(Includes shaft, housing and bearings)
Part # 9058, 5.75″ Shaft (Center) Part # 9018, 4.25″ Shaft (Outer)

OUTER BLADE DRIVER DETAIL

ITEM #

|

QTY.

|

PART #

|

DESCRIPTION

---|---|---|---

1

|

 1

|

 NB175

|

Nut – Jam 3/4-16

2

|

 1

|

 AS155

|

 Washer – Bellville 1.5 X .761 X .098

3

|

 1

|

 20651

|

Pulley – 5″

4

|

 3

|

 NB179

|

 Washer – 3/4 ID X 1 1/4 OD 18 Ga

5

|

 2

|

 B98

|

Bearing

6

|

 4

|

 NB690

|

 Bolt – Serr Flange 1/4-20 X 3/4 Grade 5

7

|

 1

|

 9057*

|

Housing – Bearing

8

|

 4

|

 NB524

|

Nut – Flange 1/4-20

9

|

 1

|

 9076

|

Shaft – L & R 4.25″

10

|

 1

|

 B98W

|

 Washer – Flat 3/4 ID X 1 3/4 OD

11

|

 2

|

 NB216

|

 Nut – Lock, Two Way 3/8-24 ZY Gr A

12

|

 1

|

 9008

|

Plate – Blade Mount

13

|

 1

|

 20186

|

Blade – G6 Gator 20 1/2″

14

|

 1

|

 NB607

|

 Washer – SP Bellvl. PLN .413 X.945 X.118

15

|

 2

|

 NB166

|

 Bolt – 3/8-24 X 1 1/4 HCC GR5 ZY

16

|

 1

|

 NB238N

|

 Bolt – HHC 3/8-24 X 1 Gr 5 Locktite

When ordering replacement parts
*USE PAINT CODE: GT=GREY TK=BLACK

MOWER DECK DETAIL

ITEM #

|

|

|

 QTY PART NO DESCRIPTION

---|---|---|---

1

|

 2

|

 18391

|

 Cover – Belt, Black Composite

2

|

 8

|

 18531

|

 Washer – Bent .25″ ID X 18GA

3

|

 8

|

 NB703

|

 Screw – MSC, 10-24 X 1 1/4

4

|

 8

|

 18532

|

 Nut – Clip, 10-24

5

|

 1

|

 —

|

 See Grass Chute & Spring Detail

6

|

 11

|

 NB596

|

 Bolt – Serr Flange 5/16-18 X 3/4

7

|

 1

|

|

 092104* Bracket – Deflector

8

|

 2

|

 NB577

|

 Bolt -1/2-13 X 3 1/2

9

|

 3

|

 3511

|

 Wheel – Gauge

10

|

 4

|

 NB121

|

 Nut – Jam Lock 1/2-13 2-Way

11

|

 1

|

 15780*

|

 Bracket – Wheel Right

12

|

 19

|

 NB170

|

 Nut – Serr Flange 5/16-18 Z

13

|

 1

|

 18383*

|

 Bracket – Middle Roller

14

|

 1

|

 NB688

|

 Nut – Nyloc Jam, 1/2-13 ZY

15

|

 1

|

 NB132

|

 Bolt -1/2-13 X 4 HCC

16

|

 1

|

 NB281

|

 Nut – Nyloc 1/2-13 ZY

17

|

 1

|

 —

|

 See Engage Lever Detail

18

|

 2

|

 T2PB

|

 Bushing – Plastic

19

|

 1

|

 18384*

|

 Bracket – Deck Hanger

20

|

 1

|

 NB509

|

 Bolt – 1/2-13 X 2 HCC

21

|

 1

|

 15779*

|

 Bracket – Left Wheel

22

|

 11

|

 26X249

|

 Screw – .312-18X.75

23

|

 1

|

 NB707

|

 Bolt – Carriage 3/8-16X4

24

|

 2

|

 AS001

|

 Roller – Anti-Scalp 3/8 ID

25

|

 1

|

 NB207

|

 Nut – Nyloc 3/8-16

26

|

 1

|

 21096*

|

 Shield – Debris

27

|

 1

|

 18382*

|

 Weldment – Deck

28

|

 2

|

 NB106

|

 Bolt – 5/16-18 X 2 3/4 HCC

29

|

 2

|

 NB181

|

 Nut – Nyloc 5/16-18

30

|

 1

|

 —

|

 See Center Blade Driver Detail

31

|

 1

|

 —

|

 See Motor Base Detail

32

|

 1

|

 —

|

 See Safety Switch Bracket Detail

33

|

 1

|

 —

|

 See Idler Detail

34

|

2

|

|

See Outer Blade Driver Detail

GRASS CHUTE & SPRING DETAIL

ITEM #

|

 QTY

|

|

 PART NO DESCRIPTION

---|---|---|---

1

|

 1

|

 166X34

|

 Spring – Torsion

2

|

 1

|

 NB182

|

 Nut – Nyloc 3/8-16 zy

3

|

 1

|

 NB784

|

 Bolt – HCC 3/8-16 x 7

4

|

1

|

092100

|

Chute – Discharge

CASTER / WHEEL ASSEMBLY DETAIL

ITEM #

|

 QTY.

|

|

 PART NO. DESCRIPTION

---|---|---|---

1

|

 2

|

 B98

|

 Bearing

2

|

 1

|

 17X195

|

 Washer – Flat

3

|

 1

|

 094618

|

 Cap

4

|

 2

|

 NB195

|

 Washer – 13/16 ID X 1 1/4 OD X 1/8

5

|

 1

|

 663L

|

 Spacer

6

|

 1

|

 NB595

|

 Nut – Locking Jam, 2 Way 5/8-11

7

|

 2

|

 NB178

|

 Washer – 5/8 ID X 1 OD 10 GA

8

|

 1

|

 665*

|

 Weldment – Caster

9

|

 1

|

 F4157WK

|

Tire/Wheel – 5/8 Bearing 13x5x6 NHS, Blk

10

|

 1

|

 NB122

|

 Nut – Nyloc Jam 3/4-16

11

|

1

|

NB624

|

Bolt – 5/8″-16 X 7″ HCC ZY Grade 5

MOTOR BASE DETAIL

PARTS NOT SHOWN


18057

|

 Harness – Wiring, Briggs (13-20 hp)

BCSR

|

Cable – Battery (10″ Red)

BCLB

|

 Cable – Battery (19 1/2″or 20″ Black)

KSK

|

 Keys – For Key Switch (set of two)

BCBT

|

 Boot – Rubber, Small, Battery Cable

Slide plastic tube snug against toggle switch.

base details

ITEM #

|

 QTY.

|

 PART NO.

|

DESCRIPTION

---|---|---|---

1

|

 10

|

 024206

|

 Screw – 12 X 1/2 Hex Self Tap

2

|

 1

|

 17840*

|

Cover – Battery Top

3

|

 2

|

 NB197

|

 Screw – Phillips Truss 8-32 X 1/2

4

|

 1

|

 17898

|

Cable – Throttle; T60

5

|

 2

|

 NB201

|

Nut – Kep 8-32

6

|

 1

|

 17616*

|

Cover – Battery Right

7

|

 1

|

 17614*

|

 Cover – Battery Top Front

8

|

 1

|

 9087

|

Nut – Key Switch

9

|

 1

|

 9088

|

Washer – Lock, Key Switch

10

|

 1

|

 685SP

|

 Switch – Toggle, Single Pole

11

|

 1

|

 3623

|

Switch – Key

12

|

 1

|

 17615*

|

Cover – Battery Left

13

|

 6

|

 NB161

|

 Screw – HX Tek 1/4 X 3/4 ZP

14

|

 2

|

 17760

|

Bolt-L

15

|

 2

|

 NB524

|

 Nut – Serr Flange, 1/4-20 Grade 5

16

|

 1

|

 14869

|

Guide – Belt; T60

17

|

 4

|

 NB275

|

Washer – SAE Flat 5/16

18

|

 2

|

 NB250

|

Bolt – 1/4-20 X 3/4 GR5

19

|

 2

|

 NB253

|

 Bolt – Serr Flange, 5/16-18 X1 1/4 Gr5

20

|

 4

|

 NB170

|

 Nut – Serr Flange 5/16-18 Case Hrd

21

|

 1

|

 N/A

|

 Engine (Reference Model Shown)

22

|

 1

|

 689L

|

 Spacer – Long, Engine Pulley, 1.5″

23

|

 1

|

 18387*

|

Motor Base – Weldment

24

|

 2

|

 NB180

|

Nut – Nyloc 1/4-20

25

|

 1

|

 17794*

|

 Bracket – Battery Hold Down

26

|

 1

|

 6000

|

Guide – Belt

27

|

2

|

NB515

|

Bolt – Serr Flange,5/16-18 X1 3/4 Gr5

When ordering replacement parts

*USE PAINT CODE: GT=GREY TK=BLACK

ITEM #

|

 QTY.

|

 PART NO.

|

DESCRIPTION

---|---|---|---

28

|

 1

|

 10636YZ

|

 Bolt – Spade, 5/16-18 X12

29

|

 1

|

 NB210Z

|

Nut – 5/16-18 HNC

30

|

 2

|

 NB181

|

Nut – Nyloc 5/16-18

31

|

 1

|

 NB280

|

 Nut – 2 Way Lock 3/8-16 Wax Gr A

32

|

 1

|

 B527

|

 Pulley – Idler, OD-3.25″, ID-3/8″

33

|

 1

|

 NB272

|

 Washer – SAE Flat 3/8 ZY Carbon Steel

34

|

 1

|

 NB107

|

 Bolt – 3/8-16 X 1 1/2 HCC GR5

35

|

 1

|

 11158

|

Nut – Jam, Nyloc 5/16-18

36

|

 1

|

 NB203

|

Nut – Kep 1/4-20

37

|

 1

|

 16000

|

Valve – Oil Drain

38

|

 1

|

 9031

|

 Key Stock – 1/4 X 1 Undr Size

39

|

 1

|

 688

|

Pulley – Engine, 5.5″

40

|

 1

|

 689S

|

 Spacer – Short, Engine Pulley, .687

41

|

 1

|

 TR150W

|

 Washer – .531IDX1 1/2ODX.062(Ht Trtd)

42

|

 2

|

 699

|

 Washer – Belleville 7/16 X 1 1/4

43

|

 1

|

 NB452N

|

 Bolt – 7/16-20 X 1 HCF GR5 Nylock

44

|

 2

|

 NB114

|

Bolt – TCS 1/4-20 X 1/2

45

|

 1

|

 1002004

|

Solenoid – 3 Pole

46

|

 1

|

 NB182

|

Nut – Nyloc 3/8-16

47

|

 1

|

 —

|

See Saftey Switch Detail

48

|

 1

|

 6009*

|

Idler – Engage Weldment

49

|

 1

|

 NB172

|

Nut – Kep 10-24 ZY

50

|

 1

|

 21894

|

 Eyebolt – 10-24 X 1 3/8, w/ Nut

51

|

 1

|

 BRS6

|

Spring

52

|

 1

|

 NB596

|

 Bolt – Serr Flange, 5/16-18 X 3/4

53

|

 1

|

 4422

|

 Spring – Idler Tension, Bent Leg

54

|

 1

|

 NB220

|

 Bolt – Shlder, 1/2 X 1-9/16 W3/4 Gr2 ZY

55

|

1

|

6736

|

Tether – Safety, Coiled

Engage Lever Detail Height Adjust Handle Detail Safety Switch & Bracket Detail

ITEM #

|

 QTY.

|

 PART #

|

 DESCRIPTION

|

ITEM # QTY.

|

|

 PART #

|

 DESCRIPTION

|

I

|

|

TEM # QTY. PART #

---|---|---|---|---|---|---|---|---|---|---

1

|

 1

|

 NB155

|

 Bolt – 1/2-13 X 5 HCC GR5 ZP

|

1

|

 1

|

 H7N1TK**

|

 Tube – Height Adjust

|

1

|

 1

|

 18390*

2

|

 1

|

 21929*

|

 Lever – Engage

|

2

|

 1

|

 ES214**

|

 Rod – Crank, For H7N

|

2

|

 1

|

 3695

3

|

 2

|

 NB121

|

 Nut – 2 Way Lock 1/2-13 ZY

|

3

|

 1

|

 H7K**

|

 Knob – Height Adjustment

|

3

|

 2

|

 NB197

4

|

 2

|

 NB555

|

Washer – 1/2

|

4

|

 2

|

 NB117**

|

 Nut – Push, 5/16

|

4

|

 2

|

 NB201

5

|

 1

|

 NB253

|

 Bolt – Serr Flng,5/16-18 X1 1/4

|

5

|

 1

|

 OD41**

|

 Decal – Ruler

|

|

|

6

|

 1

|

 2077

|

 Pivot – Handle Grip

|

|

|

|

**Parts Included in Service Part # H7N

|

|

|

7

|

 1

|

 NB170

|

 Nut – Serr Flng 5/16-18

|

|

|

|

|

|

|

8

|

 1

|

 11158

|

 Nut – Jam, 2-Wy Lck, 5/16-18

|

|

|

|

|

|

|

9

|

 1

|

 4578*

|

 Pivot – Engage

|

|

|

|

|

|

|

10

|

1

|

NB181

|

Nut – Nyloc 5/16-18

|

|

|

|

|

|

|

Wiring Schematic Harness Part # 18057 When ordering replacement parts

*USE PAINT CODE: GT=GREY TK=BLACK

ITEM #

|

 QTY.

|

 PART #

|

 DESCRIPTION

---|---|---|---

1

|

 1

|

 NB618

|

 Bolt – 3/8-16 X 1 1/4 GR5

2

|

 1

|

 6040Z

|

 Washer – Idler

3

|

 1

|

 6054*

|

 Idler – Bottom

4

|

 1

|

 6037

|

Bushing – Idler

5

|

 1

|

 NB182

|

 Nut – Nyloc 3/8-16

6

|

 2

|

 NB181

|

 Nut – Nyloc 5/16-18

7

|

 1

|

 NB280

|

 Nut – 2 Way Lock 3/8-16 Gr A

8

|

 2

|

 NB272

|

 Washer – SAE Flat 3/8

9

|

 1

|

 B527

|

 Pulley – Idler, OD-3.25″, ID-3/8″

10

|

 1

|

 21425

|

 Spring – Extension

11

|

 1

|

 NB170

|

 Nut – Serr Flange 5/16-18

12

|

 1

|

 NB501

|

 Bolt – 5/16-18 X 1 GR5

13

|

 1

|

 NB107

|

 Bolt – 3/8-16 X 1 1/2 GR5

14

|

 1

|

 NB315

|

 Eyebolt – 5/16-18 X 3 w/Gap

15

|

1

|

NB173

|

Nut – Jam 5/16-18

Belt Configuration 5058 Long Belt 6046HP Short Belt

www.swisherinc.com OWNER’S

60” FAST FINISH TRAIL MOWER

MANUAL HOW TO ORDER REPAIR PARTS:

MODEL NO. FC14560BS FC14560BS-CA

IMPORTANT

Read and follow all Safety Precautions and Instructions before operating this equipment.

Each mower has its own model number. Each engine has its  own model number. The model number for the mower will be  found at the left rear of the unit on the belt cover skirt.  The model number for the engine will be found on the top of  the blower fan housing.

All mower parts listed herein may be ordered directly from  Swisher or your nearest Swisher dealer.

All engine parts may be ordered from the nearest dealer of the  engine supplied with your mower.

Color cannot be guaranteed on service parts.

WHEN ORDERING PARTS, PLEASE HAVE THE

˝Ӵ

FOLLOWING INFORMATION AVAILABLE:

  • PRODUCT – FC60 FAST FINISH TRAIL MOWER * SERIAL NUMBER – ___

  • MODEL NUMBER – ___

  • ENGINE MODEL NUMBER – TYPE –

  • PART NUMBER

  • PART DESCRIPTION

TELEPHONE – 1-800-222-8183

FAX – 1-660-747-8650

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE

WARRENSBURG, MO 64093

CHANGING YOUR LANDSCAPE SINCE 1945

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals