HYTRONIK HIR23 Flush Mount Pir Dali Sensor Instruction Manual

HYTRONIK HIR23 Flush Mount Pir Dali Sensor Instruction Manual

 Technical Specifications

Product type Tri-level control PIR DALI sensor
Operating voltage 9.5 ~ 22.5VDC ( suitable DALI power supply)
Input current < 8mA
Pow e r consumption < 0.5W
Detection angle 360o
Detection area (Max.)*
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 2Lux / 10Lux / 50Lux / Disable
Warmming-up time 30s
Operating temperature -20o C ~ +50o C

Installation

Warnings :

1. Installation of the sensor involves connecting it to the mains supply. This work must be carried out by a specialist in accordance with electrotechnical regulations.
2. Disconnect supply before installing.

Rotary Switch Settings

A rotary switch is built inside the sensor for scene selection / fast programming. Total 16 channels available:

Rotary switch preset (Pleasesee the location in 2. Installation)

DALI group selection

`DALI group configuration can be done on PC or on the rotary switch:

1. There are 16 channels available on the rotary switch. “0” is for DALI broadcast, the rest 15 channels is for end user to define the application unit.
2. PC grouping can overwrite rotary switch grouping, the last setting controls.
3. The rotary switch channel is corresponding to the groups listed below:

Functions

This DALI sensor is designed for incoporated in the DALI system, taking command from the DALI master, accepting and carrying out the grouping work with up to 64 lumanaires. It can switch on/off, or dim the assigned group members and feed back the status to the DALI master.

Tri-level Control (Corridor Function

Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas require a light change notice before switch-off. It offers 3 levels of light: 100%–>dimmed light–>off; and 2 periods of selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.

Synchronization Function

By connecting the DALI terminals in parallel (see wiring diagram), no matter which sensor detects motion, all HMW23 in the group will turn on the lights when surrounding natural light is below the daylight threshold. The sensor antenna is shared and the detection area could be widely enlarged in this way.

Wiring Diagram

Detection Pattern

Description of the Button Functions (remote control HRC-11)

Permanent ON/OFF [ ]
Press button , to select permanent ON or permanent OFF mode. * Press button / to resume automatic operation. The mode will change to AUTO Mode after power failure.

RESET[ button ]
Press button , all settings go back to the rotary switch settings.

Scene prog. [ zone ] (One-key-commissioning) Shift [ button ] RESET[ button ] Press button , all settings go back to the rotary switch settings. Press button to initiate automatic mode.The sensor starts working and all settings remain as before the light was switched ON/OFF.
Note: the function of Semi-auto is disabled.

1. Press button “Start” to program.
2. Select the buttons in “Detection range”, / “Daylight threshold”, “Hold time”, “Stand-by time”, “Stand-by dimming level” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s). For example, to pre-set detection range 100%, daylight threshold Disable, hold time 5min, stand-by time +∞, stand-by dimming level 30%, steps should be: Press button Start, button 100%, Disable, Shift, 5min, Shift, +∞, 30%, Memory. By pointing to the sensor unit(s) and pressing Apply, all settings are passed on the sensor(s)
5. Detection range [ zone ] Press buttons in zone to set detection range at 100% / 75% / 50% / 10%. Stand-by time [ zone ] Press buttons in zone to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞. Note: “0s” means on/off control; “+∞” means bi-level control, 100% on when motion detected, and remains at the stand-by dimming level when no presence after hold-time. Daylight threshold [ zone ] Press buttons in zone to set the daylight sensor at 2Lux / 10Lux / 50Lux or Disable.
6. Press button Shift, the red LED is on for indication.
7. Press button , the ambient lux level is sampled and set as the new daylight threshold.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>