GIRA 1149 02 Smoke Alarm Device Basic Q Instruction Manual

: June 3, 2024
: GIRA

Table of Contents

GIRA 1149 02 Smoke Alarm Device Basic Q
Product features
Device description
Technical data
Documents / Resources

GIRA 1149 02 Smoke Alarm Device Basic Q

For your safety

Installation and mounting of electrical devices may only be carried out by qualified electricians. Serious injury (e.g. caused by an electric shock), fire, or material damage are possible in case of improper mounting.

Configuration and installation may only be performed by an expert.
As per EN 14676, the configuration and installation of the smoke alarm device may only be performed by a qualified expert. For this purpose, Gira offers the “Certified expert for smoke alarm devices in accordance with DIN EN 14676” online course, complete with certificate. Additional information can be found under “akademie.gira.de”.

Briefing and transfer of the instructions
Explain all the functions of the product to the end user or their representative. These instructions are part of the product and must be transferred to the end user or their representative for safekeeping.

Inadmissible installation locations
The Basic Q smoke alarm device is not suitable for installation in caravans, campers, boats etc.

Product features

The smoke alarm device Basic Q is a battery operated smoke alarm device for private residential units or similarly inhabited areas as per DIN 14676. The smoke alarm device detects the development of smoke in a timely manner and warns occupants before the smoke gas concentration becomes dangerous. The warning comes in the form of an acoustic signal.

Product features

Loud, pulsating alarm signal (min. 85 dB (A))
Smoke detection using the photoelectric scattered-light principle
Integrated function button for function test
Soiling/fault display
Permanently installed, non-removable battery
Q-Label

Scope of supply

1x smoke alarm device Basic Q
1x set of mounting hardware
1x installation and operating instructions

Device description

Mounting plate
Activation slider
Smoke alarm device
Smoke penetration openings

Selecting installation site
When selecting the installation site for the smoke alarm device, the specifications of DIN EN 14676 apply. The most important specifications are as follows:

Attach as close as possible to the centre of the ceiling (min. distance of 50 cm from walls, lights and other obstructions)
One smoke alarm device per room (max. 60 m2 area)
do not install in direct proximity of heat sources

System description of smoke alarm devices

More detailed information with regard to installation as per DIN EN 14676 can be found in the “System description of smoke alarm devices”, which is available in the Gira download area ( www.gira.de/service/download ).

Minimum protection/optimum protection

The following applies for flats and houses:

Minimum protection

One smoke alarm device in every bedroom, every child’s room and in the hallway/staircase (escape route).
In the case of open space across two levels, a smoke alarm device is to be installed on the highest level.
In the case of buildings spanning several storeys, a smoke alarm device is to be installed on each storey.

Optimum protection

One smoke alarm device per room and floor
In the case of larger buildings, use networked smoke alarm devices
Use specialised alarm devices (e.g. heat detectors) in sensitive areas.

Deceptive alarm
Some sites are unsuitable for the installation of a smoke alarm device as deceptive alarms are repeatedly triggered due to local conditions (e.g. welding/soldering work, very heavy water/cooking vapour and similar fumes). More detailed information with regard to unsuitable installation sites can be found in the “System description of smoke alarm devices”.

Installing smoke alarm device
Install the smoke alarm device as described in the following.

Install the mounting plate.
Activate the smoke alarm device.

Activation/deactivation
The activation slider is protected against being pushed in inadvertently at the factory. Remove the guard and slide the activation slider (grey) into the guide completely. The smoke alarm device is now activated. Deactivation is carried out in the reverse order.

Place the activated smoke alarm device onto the mounting plate and lock it there (turn clockwise). Removal is carried out in the reverse order. Perform the function test (see “Function test”).

Installation position
The smoke alarm device can only be installed in a certain position. A locking pin is found on the mounting plate for this purpose. It ensures that the smoke alarm device is locked properly. Before locking, you must slide the activation slider into the smoke alarm device. Disregarding this could cause the smoke alarm device to tilt on the mounting plate. At that point, an extreme exertion of force would be required for its removal.

Function button
The smoke alarm device Basic Q features an easy-access function button (grey).

The following actions can be initiated:
Function test.

Function test
The function test should be conducted:

After the initial installation
After every alarm, maintenance session and fault message

Risk of permanent hearing loss due to the loud signal tone

The loud signal tone (min. 85 dB (A)) emitted during the function test can lead to a permanent loss of hearing (e.g. tinnitus). Maintain a distance of at least 50 cm from the smoke alarm device during the function test.

Performing function test
Perform the function test as follows:

Press and hold the function button for approx. 4 s. A loud signal tone is emitted, and the ring indicator flashes.
Release the function button. The signal tone is muted and the ring indicator goes out.

Function test failure
Replace the smoke alarm device immediately if it fails the function test two times in a row. Non-operational smoke alarm devices may not be installed.

Smoke alarm devices save lives
Observe the following when using smoke alarm devices:

Use only smoke alarm devices which are compliant with DIN EN 14604.
Never cover smoke alarm devices continuously, block them with objects or paint them.
Never install smoke alarm devices if they are defective or not fully operational.

Operating and alarm signals

Problem	Solution
No signal can be heard during the function test	Check activation slider
Frequent deceptive alarms	Check installation

site for interference sources

Clean smoke alarm

device

Acknowledging alarm/deceptive alarm

If the smoke alarm device has triggered an alarm and a deceptive alarm has been identified as the culprit, you can acknowledge the alarm message by pressing the function button. Then ensure that the cause of the deceptive alarm has been eliminated.

Care and maintenance
Maintain and care for the smoke alarm device on a regular basis to ensure full operability.

Care
Wipe the smoke alarm device with a moist (not wet!) cloth on a regular basis. You can also carefully remove dust from the smoke alarm device with a vacuum cleaner (lowest setting).

Maintenance

Maintenance and duty to maintain
As per DIN EN 14676, you are required to have smoke alarm devices maintained by a qualified expert. Observe the following: If this required maintenance is not carried out, insurance coverage may be nullified in case of fire.

Maintenance book for smoke alarm devices

Gira offers the “Maintenance book for smoke alarm devices” in the download area. All the important data for the initial installation and subsequent maintenance can be entered here.

Renovation work

If possible, do not install the smoke alarm device until all renovation work has been completed. Should this not be possible, you can remove the smoke alarm device for the period of work as an alternate option. After completing all the work, carry out a function test.

Disposal
Dispose of the smoke alarm device by the date indicated on the device’s label or when the battery is flat.

DANGER
There is a risk of explosion if the battery is removed forcibly! The battery in the smoke alarm device cannot be replaced.
An explosion can occur if damage is caused by forcibly removing the battery from the device. The entire smoke alarm device must always be disposed of. The Gira smoke alarm device is an electric and electronic device in the sense of EU guideline 2002/96/EC.

High-quality materials and components were used in developing and manufacturing the device. These materials and components can be reused and recycled. Please consult the regulations governing the separate collection of electric/electronic waste valid for your country. These devices may not be disposed of with household waste. The correct disposal of waste can prevent possible negative consequences to the environment and humans.

Technical data

Power supply: Via smoke alarm device battery
Battery life: Up to 10 years (after activation)
Acoustic alarm signal: Min. 85 dB (A)
Optical display: Ring indicator (red LED)
Operating temperature: -5 °C to +55 °C
Storage temperature: -20 °C to +65 °C
Installation height: Max. 6 m
Protection type: IP 42
Housing dimensions: 110 x 40 mm (dia. x h)
Weight: Approx. 250 g
Area of application: As per DIN 14676

Declaration of performance
The Declaration of performance according to Directive (EC) No. 765/2008, Directive (EU) No. 305/2011 can be found either in the download area (gira.de/Konformitaet) or directly via the online catalogue at the product ( katalog.gira.de ).

Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade. Please submit or send faulty devices postage paid together with an error description to your responsible salesperson (specialist trade/installation company/ specialist electrical trade). They will forward the devices to the Gira Service Center.

Q-Label and warranty
The Q-label has no effect on the legal warranty.

Gira
Giersiepen GmbH & Co KG
Electrical installation systems
P.O. Box 1220
42461 Radevormwald
Phone +49 (0) 2195 602 – 0
Fax +49 (0) 2195 602 – 191
info@gira.de
www.gira.de

Documents / Resources

| GIRA 1149 02 Smoke Alarm Device Basic Q [pdf] Instruction Manual
1149 02 Smoke Alarm Device Basic Q, 1149 02, Smoke Alarm Device Basic Q, Alarm Device Basic Q, Device Basic Q, Basic Q
---|---