MokerLink 48 Port Gigabit PoE Switch User Manual

MokerLink 48 Port Gigabit PoE Switch

Product introduction

Product overview

48-Port all gigabit ethernet PoE switch with simple and convenient installation and maintenance means and rich business characteristics, which helps users to create security high performance network. The product can be widely used in the field of data exchange such as home network, multimedia classroom, security monitoring, wireless network and so on.

Port performance

• Provide 48*10/100/1000M PoE ports which can realize line speed forwarding.
• Each port supports MDI/MDIX automatic flip and duplex / rate self negotiation.
• Support IEEE 802.3x full duplex flow control and backpressure half duplex flow control.

Spare parts list

Product display

Indicator definition

Power indicator: PWR

| Green light is always on| Power on normal
Always off| No power

Network indicator

| Light is flashing| The corresponding port has data transmission
Always off| The corresponding port hasn’t data transmission

Installation&Points of attention

Checking before installation

1. Check whether the accessories are complete. If there is any omission, please contact us.
2. Check whether the power supply voltage is consistent with the working voltage of the switch,so as to avoid the equipment burning out due to high voltage.
3. Ensure that the installation position of the switch has certain ventilation and heat dissipation conditions.
4. Please keep the power off during installation to avoid potential safety hazards.
5. Please install the switch on a stable plane to avoid falling and damage.

Install to desktop

1. Attach the four non slip rubber footmats that came with the device to the bottom four corners of the switch.
2. Place the switch on the horizontal desktop in the ventilation area.
3. Insert the data cable
4. Connected the power

As shown in the figure, insert the crystal head of the data cable into the network port. When you hear a clear click, it indicates that the crystal head is successfully connected with the network port of the switch. Just plug in all the network cables of the network equipment in this way.

Install to cabinet/Rack

1. install the rack lug attached to the equipment to both sides of the switch with screws
2. Install floating nut on cabinet / rack
3. Put the switch installed with the lug into the cabinet and screw on the screw to complete the installation.
4. Connected the power

Points of attention

1. Do not stack heavy objects on the switch to avoid danger.
2. In order to avoid the risk of electric shock, please do not open the machine box when the switch is working, even if it is not powered on, please contact us in case of any problem.
3. Before cleaning the switch, pull out the power plug of the switch. Do not wipe it with wet fabric or clean it with liquid.
4. If the power adapter is damaged, do not replace it with other power adapters. This switch should be equipped with original power adapter.

Application

Common troubleshooting

The PWR indicator is not on after the power is connected Check whether the power adapter and plug are connected correctly, whether the power cord is damaged, and whether the power adapter is damaged. Switch cannot communicate after power up Check whether the switch indicator is on. If the indicator is off, the network cable is not connected. If the indicator is on, the communication fault is indicated. Switch network speed suddenly become very slow Take off the plug and restart the switch. [If the above problems or other switch problems can not be solved, please contact us for technical support]

Product parameter

Network Protocol

| IEEE 802.3

IEEE 802.3i 10BASE-T IEEE 802.3u100BASE-TX IEEE 802.3ab1000BASE-T

Port Specification| 10/100/1000BaseT（X）Auto
PoE Standard| IEEE80.23af/at
Transmission Mode| Store and Forward（full wirespeed）
Bandwidth| 112Gbps
Packet Forwarding| 80.64Mpps
MAC Address| 8K
Buffer| 4.1M
Transmission Distance| 10BASE-T: Cat3,4,5 UTP(≤250 meter)

100BASE-TX: Cat5 or later UTP(150 meter) 1000BASE-TX: Cat6 or later UTP(150 meter)

Watt| ≤45W

LED Indicator

| PWR:Power LED

1-48:(Link LED =10/100/1000M)

Power| Built-in Power AC：100～240V 50-60Hz 1A
Operating Temperature/Humidity| ****

-10～+55°C；5%～90% RH Non coagulation

Storage Temperature/Humidity| ****

-40～+75°C；5%～95% RH Non coagulation

Product size/Packing size（LWH）| 440mm200mm45mm 513mm300mm95mm
N.W/G.W（kg）| 2.2kg/3.5kg
Installation| Rack-mount(optional machine hanger spare parts)
Lightning protection level| 3KV 8/20us； IP30

Certificate

| 3C;

CE mark, commercial；CE/LVD EN60950； FCC Part 15 Class B；RoHS；

Wuhan MokerLink Technology Co.,Ltd Rm10,13/F, Main Building 7,Changhang Lanjing International,
No.116 Gaoxin Ave., Hongshan Dist., Wuhan, China http://www.mokerlink.com   support@mokerlink.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>