MokerLink POE-G042GSO Rainproof PoE Switch User Manual
- June 10, 2024
- MokerLink
Table of Contents
MokerLink POE-G042GSO Rainproof PoE Switch
About guide
This guide provides instructions to install the Switch.
Note: The model you have purchased may appear slightly different from the illustrations shown in the document. Refer to the Product Instruction and Technical Specification sections for detailed information about your switch, its components, network connections, and technical specifications.
This guide mainly divided into 4 parts:
- About guide: Terminology/Copyright and statement
- Product introduction: functional overview and introduction of panel definitions
- Hardware installation: step by step hardware installation process
- Technical specifications
Terminology
Note: indicates important information that helps a betteruse of the
device.
Warning: indicates potential property damage or personal injury.
Copyright and statement
Without the express written permission of the company, no unit or individual
is allowed to imitate, copy, transcribe or translate part or all of the
contents of this book without authorization.
The pictures and data shown in this guide are for reference only, subject to
change without notice.
Products Introduction
Thanks for purchasing the Switch products.
This product is an outdoor rainproof full Gigabit PoE switch. Equipped with 4 10110011 000Mbps RJ45 PoE ports and 2 Gigabit SFP ports, which can meet the full speed forwarding of the ports. This product adopts ABS plastic outdoor rainproof shell for, Holding pole installation. Excellent performance can help you widely used in wireless, surveillance and other fields.
Front Panel
LED Lamp
Power LED: The Power LED lights up when the switch is connected to a power
source.
Link/Act indicator: the light indicates the network connection through the
corresponding port. Flicker indicates that the switch is sending or receiving
data PoE indicator: constant brightness indicates that the PD device is
connected to the corresponding port, and extinguished indicates that the port
is not powered or no PD device is found .
Rear Panel
The back is composed of mounting brackets, which can be used for wall -mounting and pole -mounting.
Hardware installation
This chapter provides unpacking and installation information for the Switch.
open a seal
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged. If any item is missing or damaged, please contact the local reseller for replacement.
- → Switch 1 pcs
- → User’s manual 1 pcs
- → Power cord 1pcs
Switch installation
For safe switch installation and operation, it is recommended that you:
- → Visually inspect the power cord to see that it is secured fully to the AC power connector .
- → Make sure that there is proper heat dissipation and adequate ventilation around the switch .
- → Do not place heavy objects on the switch.
Holding pole installation
Connect power supply
The power connection uses a quick-plug terminal block connector. It is recommended that the user use a cable with a current capacity of more than 6A.
Warning: When connecting to the power supply system, please pay attention to the polarity marks of the interface avoid connection errors.
The terminal block connector the of is used for power input. Please follow the steps below to insert the power wire:
- Insert two power lines into the hole at the end side of the connection.
- tighten the screw above the connection end clockwise with a screwdriver, for preventing the power line from loosing.
- The other end of the power line is connected to the power supply system.
| 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|
| L | NC | N | NC | Ground |
The wire gauge for the terminal block should be in the range between 12-24AWG.
Power Input: Supports input voltages 100-240VAC, 50/60Hz. Grounding: use specialized ground lead connect
Technical specifications
| Project | Describe |
|---|
Attributes
Networking Interfaces| 4 x 10/100/1000Mbps RJ45 Ethernet Ports 2 x 1Gbps
SFP Ports
LED Indicators| Power, Link/Act, PoE
Performance
Switching Capacity| 12 Gbps
Forwarding Capacity| 8.93 Mpps
Forwarding Mode| Store and Forward
Packet Buffer Memory| 2 Mbit
MAC Address Table| BK
Physical
Dimensions| 295x206x50mm
Operating Temperature| 0 to 40°C
Storage Temperature| -10 to 75°C
Operating Humidity| 5 to 95% Noncondensing
Power Method| 100- 240VAC, 50/60Hz
Power Consumption| SW
Casing| ABS plastic
Installation| Holding pole installation
Power over Ethernet
PoE Ports| 4
PoE Standard| IEEE802.3af / IEEE802.3at
PoE Power Budget| 65W
Max. PoE Wattage per Port| 30W
PoE Voltage| 52V
PoE Pin Assignment| V- (RJ45 Pin1,2), V+ (RJ45 Pin 3,6)
Get help or claim warranty
Visit Here:http://www.mokerlink.com/support/
or Scan QR Code
Wuhan MokerLink Technology Co.,Ltd
Rm 10, 13/F,Main Building 7,Changhang Lanjing International,
No.116 Gaoxin Ave.,Hongshan Dist.,Wuhan,China
http://www.mokerlink.com
support@mokerlink.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>