MokerLink G082GS Fiber Switch User Manual
- October 30, 2023
- MokerLink
Table of Contents
Fiber Switch Series
User Manual
G082GS G092GSM
10G080GS 10G080GSM
Product introduction
The 1G /10G SFP optical series ethernet switch with line speed forwarding
capability per port. It has the characteristics of fiber cable as transmission
medium, high speed, SFP transmission distance up to 100KM and strong anti-
interference capability. This series products can be widely used in data
exchange fields such as home network, security monitoring and wireless
networking.
Product Characteristic
- Each port supports MDI/MDIX auto flip and duplex / rate self negotiation.
- Support IEEE 802.3x full duplex flow control and back pressure half duplex flow control.
- Support jumbo frame transmission.
- Built-in efficient exchanging CPU, safe, stable and high speed.
- Optional single-mode/multi-mode SFP module.
- SFP transmission distance: Max. 100KM.
- Panel indicator monitors operating status and helps fault analysis.
Product display
Indicator definition
Indicator | Status | Description |
---|---|---|
Power LED : PWR | Always ON | Normal |
Always OFF | Power unconnected | |
SYS | Always ON | System operates normally |
Port LED | Orange LED Always ON | Corresponding Ports operate at 1000M mode |
Green LED Always ON | Corresponding Ports operate at 100M mode | |
SFP LED : 1-8 | Always ON | SFP signal communicates |
Product supporting list
Attention: Fiber modules are not
included in models with SFP; Please contact us in time if shorted or damaged
accessories found.
Login Management (For G092GSM / 10G080GSM)
This content is only applicable to managed type of products, please read this
help information for the first application
Web Management
- Connect the device and PC, to ensure that the device initialization is complete.
- Configure the IP address of the PC to be in the same network segment as the switch default IP address.
- Enter “http://192.168.2.1” in the address bar of the opened PC browser, then press “enter” to the web management login interface, input the default user name “admin” and password “admin”, and press “enter”.
Console Port Management
- Connect the PC and the switch console port with the console cable.
- Start the terminal simulation software, create a connection, select a serial port, and set communication parameters in consistent with the default configuration of the switch’s console port, as listed below:
Transmission rate: 115200
Data bits: 8 Parity bit:
None Stop bits: 1
Connecting Equipment
Network Cable
Pls use Cat5 and above network cable.
Optical Fiber
- Optical fibers must be used with the optical modules.
- Fiber bending radius must not be less than 40mm.
Power Cable
- Distance between power cable and network cable should be more than 10cm.
- The AC power please use the local AC power cable.
- The DC power please pay attention to the positive and negative electrodes.
Flow control mode: None
Technical parameter (For G082 GS/G092 GSM)
Model | G082GS | G092GSM |
---|---|---|
Product | 10 Port Gigabit Unmanaged Fiber Switch | 11 Port Gigabit Managed Fiber |
Switch
Port| 210/100/1000Base-TX RJ45 port (Data) 81000M SFP| 210/100/1000Base-TX
RJ45 port (Data) 91000M SFP
Network Protocol| IEEE802.3
IEEE802.3i 10BASE-T
IEEE802.3u100BASE-TX IEEE 802.3ab1000BASE-T IEEE802.3x
IEEE 802.3z 1000BASE-X
Port Specification| 10/100/1000BaseT ( X ) Auto
Transmission Mode| Store and Forward(full wirespeed)
Bandwidth| 32Gbps| 56Gbps
Packet Forwarding| 14.44Mpps
MAC Address| 8K
Buffer| 4.1M
Transmission Distance| 10BASE-T Cat3,4,5 UTP(5250 meter)
100BASE-TX Cat5 or later UTP(150 meter)
1000BASE-TX Cat6 or later UTP(150 meter)
Optional:Single mode single fiber(transmission distance:MAX 20km)
Optional:Single mode double fiber(transmission distance:MAX 20km)
Optional:Multiple mode double fiber(transmission distance:MAX 850 meters/20km)
Optional 3-80km SFP
Watt| 5 15W| 5 20W
LED Indicator| PWR: Power LED
SYS: (System LED)
Port: (Green=10/100M LED Yellow=1000M LED )
1-8: (SFP LED)| PWR: Power LED
SYS: (System LED )
Port: (Green=10/100M LED Yellow=1000M LED )
3-11: (SFP LED )
Power| External power DC 12V 2A
Operating Temperature /Humidity| -10 — +55°C ; 5% — 90% RH Non coagulation
Storage Temperature /Humidity| _40 — +75°C ; 5% — 95% RH Non coagulation
Product size /Packing size (LWH)| 225mm105mm35mm 295mm170mm100mm|
295mm170mm100mm 300mm205mm55mm
N.W/G.W(kg)| 0.6kg/0.9kg| 0.7kg/1 kg
Installation| Desktop
Lightning protection level| 3KV 8/20us ; Ip30
Certificate| CE mark, commercial ; CE/LVD EN60950 ; FCC Part 15 Class B ; RoHS
;
Warranty| Whole device for 1 year(Accessories not included)
Technical parameter (For 10G080 GS /10G080 GSM)
Model | 10G080GS | 10G080GSM |
---|---|---|
Product | 8 Port 10G Unmanaged Fiber Switch | 8 Port 10G Managed Fiber Switch |
Port | 8`10Gbps SFP+ | |
Network Protocol | IEEE802.3 / IEEE802.3ae IEEE802.3i 10BASE-T |
I EEE802.3u100BASE-TX IEEE 802.3ab1000BASE-T I EEE802.3x
IEEE 802.3z 1000BASE-X
Port Specification| 1G/10G Auto
Transmission Mode| Store and Forward(full wirespeed)
Bandwidth| 160Gbps
Packet Forwarding| 119.04Mpps
MAC Address| 16K
Buffer| 12M
SFP Support Type| Multimode dual fiber
Single mode single fiber
SFP to RJ45 power module
Support CPRI mode optical port interconnection
Jumbo frame| Up to 12KB
LED Indicator| PWR: Power LED
Port: 1G Link LED; 10G Link LED
Power| External power DC 12V 2A
Operating Temperature /Humidity| -10 — +55°C ; 5%— 90% RH Non coagulation
Storage Temperature /Humidity| _40 — +75°C ; 5% – 95% RH Non coagulation
Product size /Packing size (LWH)| 223mm103mm28mm 281mm107mm100mm
N.W/G.W(kg)| 0.71kg/1.16kg
Installation| Desktop
Lightning protection level| 3KV 8/20us ; ip30
Certificate| CE mark, commercial ; CE/LVD EN60950 ; FCC Part 15 Class B ; RoHS
;
Warranty| Whole device for 1 year(Accessories not included)
Get help or claim warranty
Visit Here: http://www.mokerlink.com/support/ or Scan QR Code
Wuhan MokerLink Technology Co.,Ltd
Rm10,13/F,Main Building 7,Changhang Lanjing International
No.116 Gaoxin Ave.,Hongshan Dist.,Wuhan,China
http://www.mokerlink.com
support@mokerlink.com