CASTLES TECHNOLOGY S1E2 POS Terminal User Manual

TECHNOLOGY S1E2 POS Terminal
User Manual
Castles Technology Co., Ltd.
6F, No. 207-5, Sec. 3, Beixin Rd., Xindian District,
New Taipei City 23143, Taiwan R.O.C.
http://www.castech.com.tw

WARNING

Information in this document is subject to change without prior notice.
No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Castles Technology Co., Ltd.
All trademarks mentioned are proprietary to their respective owners.

Revision History

Regulatory instruction of usage

• Before using the terminal, please check the does it has been disassembled, modified, or happened the abnormal situation. If yes, please do not continue to use.

• Please stay away from strong electromagnetic waves.
  (Example) Microwave ovens, magnets, shoplifting prevention devices, high- voltage wires, automatic doors, communication antennas, etc.

• Condensation can occur when moving from a cold place to a warm place. If condensation occurs, do not use the unit until the connected water droplets evaporate.

• Static electricity may occur in some places (such as where you are using a carpet).

• Please do not leave it in the sun for a long time.

• Please operate the unit carefully as it is a precision instrument. Do not apply impact, drop or heavy objects on top of the unit.

• Do not attach dust, oil, etc. to a part of the power terminal. Also, please do not scratch.

Hardware Setup

2.1. Parts of the Terminal

1. Contactless Card Landing Zone
2. LCD Display (5”)

Rear

3. Product Label
4. Rechargeable Battery Cover
5. Rear Camera
6. Photo-Flash| 7. Speaker
8. SAM Slots 1-2
9. GSM SIM Card Slots 1-2
10. Micro SD Card Slot
---|---

Top
11. Barcode Scanner

Left side

Right side

14. Headphone Jack
15. Barcode Scan Button
16. USB Type C Slot
17. LED Indicator
Green Light: External power source connecting and battery is full.
Red Light: Battery charging function activated| 18. Microphone
19. Charger Pin
20. Magnetic Stripe Reader
21. Barcode Scan Button
22. Power Button
23. Contactless LED Indicator
---|---

2.2. Insert Battery
Step 1: Remove the battery cover.
Step 2: Insert the battery into the compartment
Step 3: Reverse the operation of step 1 to install the battery cover.
Note 1: Please confirm the battery is installed before power on the terminal.
Note 2: Highest specified charging temperature: 45±3°C; Lowest specified charging temperature: 0±3°C.

2.3. Insert SAM Card

Step 1: Remove battery cover / back cover
Step 2: Insert SAM card into desire slot.

SAM 1 & 2:
Gold contact is on the upper side of the card and facing down. Step 3: Reverse the operation of step 1 to install the battery cover.
Step 3: Reverse the operation of step 1 to install the battery cover.

2.4. Insert GSM Micro SIM Card

Step 1: Remove battery cover / back cover
Step 2: Insert GSM Micro SIM card into desire slot.
SAM 1
Gold contact is on the upper side of the card and facing down.
SAM 2
Gold contact is on the upper side of the card and facing down.
Step 3: Reverse the operation of step 1 to install the battery cover.

2.5. Insert Micro SD card

Step 1: Remove battery cover / back cover
Step 2: Place Micro SD memory card.
Step 3: Reverse the operation of step 1 to install the battery cover.

Appendix

3.1. FCC
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The  further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function  is available.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.

3.2. IC
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual.  The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

3.3. UL/IEC 62368-1

• Warning:
  Power cord shall be connected to a socket-outlet with earthing connection.

• Warning:
  Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in accordance with local disposal regulations.

• Warning:
  This product is intended to be supplied by a Listed Power Adapter “L.P.S.” (Or “Limited Power Source”) and is rated at 5 Vdc, 2 A min., Tma = 40 degrees C.

References

• castech.com.tw
• castech.com.tw/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>