CDN TM4 Digital Timer User Manual
- June 3, 2024
- CDN
Table of Contents
CDN TM4 Digital Timer
Specifications
- PRODUCT DIMENSIONS: 7 x 4.7 x 0.9 inches
- ITEM WEIGHT: 4 ounces
- BATTERIES: 2 AAA batteries
- MATERIAL: Plastic, Acrylonitrile Butadiene Styrene
- HUMAN INTERFACE INPUT: Buttons
- BRAND: CDN
Introduction
CDN Digital timers keep track of timing, either to initiate an action, to begin timing after an action has been initiated, or both. While some products can be programmed, others might be fixed at a particular internal time and function. These devices differ in terms of the time range settings in addition to the quantity and variety of functions.
OPERATING INSTRUCTIONS
- To install Battery (1.5V, AAA included):
- Slide Battery Cover in direction of arrow.
- Install battery. Observe polarity, noted inside compartment.
- Replace Battery Cover.
To set time
Enter Hours and/or Minutes by pressing HR and/or MIN key. Press key once to advance time by one digit. Hold key down to advance digits rapidly.
Operation
-
Press START/PAUSE to start timing. The colon will start to flash, indicating that the TM4 is counting down.
-
To interrupt timing – press START/PAUSE. The colon will stop flashing, and the count will stop. Press START/PAUSE again to resume timing.
-
When display reaches 0:00 the alarm will sound. To stop the alarm, press ALARM STOP. If the ALARM STOP key is not pressed, the alarm will stop automatically in 30 seconds.
-
To reset display to 0:00 before the time is up, press
STOP/PAUSE to stop the count. Then press CLEAR to reset the display to 0:00. NOTE: As a precaution against accidentally resetting the display, the count must first be stopped before resetting to zero. -
Lockout feature prevents clock time or count time from being accidentally cleared.
NOTE
REMOVE STICKER FROM DISPLAY BEFORE USE
5 Year Limited Warranty
Any instrument that proves to be defective in material or workmanship within
five years of original purchase will be repaired or replaced without charge
upon receipt of the unit prepaid at the address listed to the right. This
warranty does not cover damage in shipment or failure caused by tampering,
obvious carelessness or abuse.
Model TM4
Made in China, © 2001 Component Design Northwest
Component Design Northwest, Inc.
P.O. Box 10947 Portland, OR 97296 info@cdnw.com www.cdnw.com
Frequently Asked Questions
Does this timer remember the last time setting it was used, or does it require reprogramming each time?
Previous programming is not retained. It is merely a timer and doesn’t actually perform programming. You simply type in the desired duration for the timer to run before it sounds a loud alarm that lasts for a minute or two before turning off. I’ve had mine for a while and use it to remind me to turn off the sprinkler, time my cooking, etc. I’m not sure if they have added any new features since I purchased mine. It’s great, and I use it a lot.
How do you turn timer off? There isn’t an On/Off switch visible.
The timer’s numbers are constantly on.
Hour count is also included in the clear button. I want to clear, but how do I know?
To stop the timer when it is set, press the start/stop button, and then press the clear button.
Does the alarm go off after a set amount of time or does it keep beeping?
I estimate that it does stop after 20 seconds. I bought it for my mother, and from what I recall (from going to her house), the timer doesn’t stop beeping for about 20 seconds.
How can the time be changed on my CDN clock?
To choose the countdown mode, slide the TIMER switch to the right. The word TIMER is displayed. 2. Press the HR MIN and/or SEC buttons to enter the desired time.
My Cdn timer needs to be reset?
To reset to 0:00, press the MIN and SEC buttons simultaneously. Keep your timer away from extreme heat, moisture, and shock. Avoid coming into contact with any corrosive substances, such as cleaning products, alcohol, or perfume.
How do I manually change the time on my Android?
Launch the Clock app on your phone.
Tap More. Settings. Tap Home time zone to select your time zone at home. Tap Change date & time to instantly update your time zone. automatic time zone setting Tap Change date & time Set time zone automatically to have your time zone updated based on your location.
How do I fix a CDN issue?
Checking to see if it is protected by a firewall should be your first step. If that’s the case, you must turn it off because you cannot use a CDN and be protected by a firewall at the same time. Log into your client area and purge all the content from your CDN Resource if you aren’t protected by a firewall.
How do I find out if a website uses a CDN?
You only need to look for an x-cache response header to determine whether AWS Cloudfront (CDN) is being used. It will make reference to the Cloudfront (ie. Hit from Cloudfront or Miss from Cloud front).
How can I resynchronize my time?
Then select Time & Language. Toggle to Date & Time. Click the Sync now button located under the “Synchronize your clock” section.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>