FANTEM ZW800 Z Wave Module Development Kit User Manual

FANTEM ZW800 Z Wave Module Development Kit

FEATURES & SPECIFICATIONS

Hardware Characteristics

Software Characteristics

(0x07)
Generic Device Type| GENERIC_TYPE_ENTRY_CONTROL (0x40)
Specific Device Type| SPECIFIC_TYPE_DOOR_LOCK (0x01)
Security Class| Non-Security, S0, S2 -ACCESS
SmartStart| Support. After powering on, SmartStart is auto-active if it’s out of the Z-Wave network.
Over The Air （OTA）| Support. Firmware can be updated via RF.
Multichannel Device| No
---|---
Association| Support. Refer to Section 4.7 Association Group Info.
Factory Reset| Support. Refer to Section 3. 6 How to factory reset.
Power-down Memory| Support. All command settings will stay unchanged even power down.
Timed battery report| Support. Refer to Configuration Parameter 3.
Low battery warning| Support.
Door State Report| Support. When the door lock mode is changed, send out a notification via Group 1.
User code Report| Support. When user code changes, send out a notification via Group 1.

PRODUCT QUICK START

About is Z Wave

• Z -Wave is the international wireless protocol for communication in the Smart Home.
• Z- Wave ensures a reliable communication by reconfirming every message (two way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
• This devic  e and every other certified Z Wave device can be used together with any other certified Z Wave device regardless of brand and origin as long as both are suited for the same frequency range.

About SmartStart

SmartStart-enabled products can be added into a Z Wave network by scanning the Z Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the networ k vicinity.

How to add the product into Z Wave network

1. Follow the user guide of hub to enter inclusion mode.
2. Operate on lock following guide below:
   • Enter master mode( mode(** + Master PIN Code +
   • Input ” to enter “Network
   • Input “1” + to enter Include mode”

How to remove the product from Z Wave network

1. Follow the user guide of hub to enter exclusion mode.
2. Operate on lock following guide below:
   • Enter master mode( mode(** + Master PIN Code +
   • Input ” to enter “Network
   • Input “2” + to en ter “Exclusion

How to factory reset

1. Operations on lock
   • Keep your lock in “unlock” status
   • Use the provided reset pin to press and hold the reset button for more than 5 seconds until hearing beep sound
   • If reset is successful, the bolt will extend on its own to learn the orientation of the door
2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
3. Default master pin code is “12345678”, please modify it after reset Refer to programming instruction)

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee tha t interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interf erence by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

ISED Statement

•  This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digit al apparatus complies with Canadian CAN ICES 3 (B)/NMB 3(B).
• This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
• This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

RF Exposure Statement

The device has been evaluated to meet general RF exposure requirement. The device can be used installed and operated with minimum distance 0mm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>