ICM CONTROLS ICM530 Surge Protective Device User Manual

ICM CONTROLS ICM530 Surge Protective Device

Please follow all State, Local and National electrical codes when installing this product. Installation should only be done by a licensed electrician for Type 1 devices or a licensed HVAC technician for Type 2 devices.

ELECTRICAL SHOCK HAZARD – Before installing this unit, turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position.

• WARNING — No Serviceable Parts (Attention: Aucune pièce remplaçable ou reparable).
• WARNING — Shock hazard — Do not open (ATTENTION – RISQUE DE CHOC – NE PAS OUVRIR).

Maintenance

Periodically check the LED status on the SPD. If the Greenlight is OFF, the protection is no longer available and the SPD needs to be replaced immediately. 12 AWG stranded copper wire or larger required. Product contains no serviceable parts. This device features an internal protection that will disconnect the surge protective component at the end of its useful life but will maintain power to the load – now unprotected.

Mode of Operation

The ICM530 is a UL Listed Type 1&2 Surge Protective Device for three phase Delta 240 VAC or Wye 120/208 VAC three phase voltage configurations. When a surge occurs, the ICM530 will absorb the surge up to the limits expressed in the specifications section of this guide. The ICM530 incorporates thermal protection on the surge elements (TMOV’s) which allows for safe disabling of the surge elements when a surge exceeds the thermal limits of the device. The ICM530 has a status light on the control which identifies operational status when illuminated. The ICM530 can be installed as a Type 1 or Type 2 device for both indoor and outdoor applications. Suitable for use on a circuit capable of delivering not more than 200kA RMS symmetrical amperes, 240V maximum (Convient à des circuits produisant au plus 200kA RMS A eff.”, 240V maximum).

Installation Instructions

The conductors used to connect the SPD shall not be any longer than necessary and shall avoid unnecessary bends.

• Turn off the main breaker and/or main power to the service disconnect.
• Determine if you have a Wye or Delta configuration.
• Verify your mains voltage and match that with ICM530 ratings.
• Remove the cover on service disconnect or the electrical panel.
• Mount the ICM530 through the 3/4” conduit connection of the electrical panel.
• Remove the retaining ring and washer on the ICM530.
• Feed the wires into the electrical panel or service disconnect.
• Re-secure the retaining ring and washer.
• Route the white wire to the neutral lug and secure.

Wiring Type 1 installation

• Route the three black wires to the appropriate L1, L2, L3 connections before the breaker panel as seen in the wiring diagram for Type 1 installation and according to your local, state, and national electrical codes.

Wiring Type 2 installation

• Route and connect the three black wires (L1, L2, and L3) to the individual breakers on the circuit breaker panel as seen in the wiring diagram for Type 2 installation and according to your local, state and national electrical codes.
• There will be a white wire which is only used in the Wye configuration and which needs to be capped off in the Delta configuration.
• Reinstall cover on service disconnect or the electrical panel.
• Restore power; Green LED should be on indicating full protection.

Specifications

6 for Wye configuration (neutral tied to ground)

VPR (Vpk)| VOLTS (V) MODE      VPR (Vpk)

240                 L-L            1200

208/120          L-L            1200

L-N            700

Maximum Continuous Operation Voltage (MCOV)| L-L: 300 VAC L-N: (for Wye configuration only): 150 VAC
Input Power Frequency| 50/60Hz
Diagnostics| Green LED indicates surge protection present
Enclosure Rating| NEMA/Type 4X water tight plastic enclosure for outdoor and indoor installation
Installation Point| Electrical panel/disconnect
Dimensions| 4.3” X 4.1” X 2.3”
Operating Temperature| -40°F to 185°F (-40°C to 85°C)
Operating Humidity| Less than 85%, noncondensing
Operating Altitude| Less than 2000 meters
Agency Certification and Approvals| ANSI/UL1449 4th Edition Listed Device cULus Listed

Type 1 Wiring Fuse Disconnect

Type 2 Wiring Circuit Breaker

Note 1: For the ease of checking the SPD protection status, the LED display should face outwards after installation has been complete.

Note 2: ICM530 is a Type 1 and 2 SPD, designed to be compatible with 3-phase Delta and 3-phase Wye voltage configuration. Please check your supply voltage configuration and voltage levels before installing the ICM530 per wiring diagram.

Note 3:

• When installing the Surge Protecting Device (SPD), avoid sharp bends in the conduit and long line sets
• Keep the mounting conduit straight and short in length.

Legend

BLK Black WHT White A,B,C Incoming phase

Type 1 Wiring Fuse Disconnect

Type 2 Wiring Circuit Breaker

Note 1: For the ease of checking the SPD protection status, the LED display should face outwards after installation has been complete.

Note 2: ICM530 is a Type 1 and 2 SPD, designed to be compatible with 3-phase Delta and 3-phase Wye voltage configuration. Please check your supply voltage configuration and voltage levels before installing the ICM530 per wiring diagram.

Note 3:

• When installing the Surge Protecting Device (SPD), avoid sharp bends in the conduit and long line sets.
• Keep the mounting conduit straight and short in length

Legend

BLK Black WHT White A,B,C Incoming phase

ICM CONTROLS www.icmcontrols.com 7313 William Barry Blvd., North Syracuse, NY 13212

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>