SW-MOTECH KFT.05.987.60000B AERO ABS Side Case System Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH KFT.05.987.60000B AERO ABS Side Case System
Mounting Instructions
SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:
All screws, bolts, and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts, and nuts.
AERO ABS side case set
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or \ even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist. This product was developed for vehicles in \ their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TUY regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type. After fixation also makes sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way. Lamps as taillight and turn signals must not be limited in their
function. Cables and hoses must not rub and/or be pinched. Before starting to
ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
- ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
- ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
- ATTENTION: Before riding and at each stop (every 200 km) check the proper fixation of the product!
PARTS LIST
A ll measurements in millimeters. • The second number indicates the total quantity of the part in the delivery. No torque specifications: Use the torque defined by the vehicle manufacturers! be used as long as it is within the vehicle manufacturer’s specifications.
CARE
To clean the side cases, use warm, soapy water and a soft, clean cloth. Rinse
with clean water. Do NOT use strong cleaning agents, rough cleaning tools or a
high-pressure washer! Clean the side cases after riding in salty conditions,
to avoid damage from salt. Hard-to-open zippers can be loosened with a small
amount of talcum powder.
ATTENTION: Surface materials can experience color changes or fading when
exposed to direct sunlight for extended periods of time and by environmental
factors (e.g., SMOG, acid rain, etc.]! SW-MOTECH assumes no liability for this
MOUNTING
-
Step [1]: Place the four locking openings of the side case [1) onto the guide bolts of the mounted SW-MOTECH side carrier.
-
Step [2]: Press the side case slightly downward, until it properly rests on the side carrier. ATTENTION: Make sure that all four guide bolts engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism and that the red marking under the slider is not visible! To release press the slider downward.
ATTENTION: All components of the side case must not contact any hot or moving parts of the vehicle! All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream! After mounting, make sure there are no clearance issues while the suspension is both compressed and extended. -
Step [3]: To protect the mounted side case against theft, open it [11. Then press the locking button and turn it according to the arrow mark until the locking button engages.
-
Step [4]: Then lock the closed zipper with the included lock [21. We recommend leaving the locking button in the closed position during the ride.
Use the included waterproof inner bag (3) to protect your luggage from moisture.
For an easier loading of the side case (11. open the buckles and hook and loop fasteners of the opening reductions, as shown in the drawing.
ATTENTION: Make sure weight is evenly distributed between the left and
right side if you want to use both side cases! Make sure that the loading is
secured against shifting during the ride!
ATTENTION: Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/side case!
Anti-theft protection for PRO/ EVO side carrier
ATTENTION
NEVER lubricate lock cylinders with oil! Use graphite powder only!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>