WOODBRIDGE BID01 Smart Toilet Seat Instruction Manual

INSTALLATION MANUAL BID 01
ELECTRONIC TOILET SEAT

BID01 Smart Toilet Seat

• Thank you for choosing our products.Please read the instructions carefully before installation and keep it available for future maintenance or reference.
• Our company reserves the right of final interpretation for this manual. The manual is subject to change without notice.

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions shouldalways be followed, including the following:

1. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
   been given supervision or instruction.

2. Children being supervised not to play with the appliance.

3. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

4. Children shall not play with the appliance.

5. Cleaning and user maintenance shall not be made by children without supervision.
   READ ALL INSTRUCTIONS BEFORE USING

DANGER –To reduce the risk of electrocution:

1. Do not use while bathing.
2. Do not place or store product where it can fall or be pulled into a tub or sink.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into water. Unplug immediately.
5. Do not wash the main unit or electrical plug with water or detergent.
6. Do not handle the electrical plug with wet hands.
7. Do not put a hand or other staff over the outlet of air dryer or block the outlet of air dryer.
8. Never disassemble,repair or modify this product.
9. During installation, disassembly, repaire and maintenance of the product,the power plug must be switched off and water supply be shut off.

WARNING–To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never use while sleeping or drowsy.
6. Never drop or insert any object into any opening or hose.
7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
8. Connect this product to a properly grounded outlet only. See Grounding Instructions.
9. Do not throw cigarettes and other burning stuff into toilet, otherwise it might cause fire.
10. This product is electric appliance, so it must be placed far away from water. Please don’t drench urine and other liquid to it.
11. Do not lay on side or upside the product during the electrical circuit.
12. It is prohibited to use other electric appliances in the same socket.
13. It is forbidden to use the power extension or unstable loose outlet.
14. The old aging water supply hose can not be used, otherwise it might cause leakage, fire or electrical shock.Installation of the bidet seat should include specified  components and new water supply hose.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION – Indicates that failure to follow the instruction may cause body injury or property damage.

1. Do not install or use the product in wet places as steam room etc.This product must be connected to properly grounded power outlet socket.
2. It is recommended to use water-proof electrical outlet which should be lnstalled in the place where is not easily got wet.
3. This product should be used with AC 110V-120V,50/60Hz electrical current only,load current is at least 15A. P ower plug must be equipped with ground fault circuit interrupter or ground fault electrical leakage protector or similar high sensitive, rapid type leakage switch (Rated sensitive current under 6mA).
4. When it thunders,it is strongly recommended to pull out the power plug.
5. Do not stand on ceramic toilet.
6. Ceramic toilet must install floor fixing bolt.
7. Do not stand on product unit,seat and cover.
8. Do not lean against the seat cover when using the product,to avoid damage.
9. This product is equipped with soft-closing seal cover.Heavy pressing or pushing may damage the soft-closing damper.
10. Do not use lacquer thinner,petrol,liquid medicine,detergent,insecticide,toilet cleanser and scrubbing brush to clean the product.
11. Exposure to direct sunlight is prohibited.
12. Only use tap water or potable water;otherwise it may cause chafing.
13. Do not connect water supply to heater outlet.Make sure inlet water temperature at 3~35˚C
14. When the room temperature is under zero degree,please dry up the water tank,to avoid freezing.
15. Raise rest room temperature to prevent the toilet from damage due to freezing.
16. When move the product from cold or wet environment into normal room temperature,wait for 2 hours until the condensation water is fully volatilized.Doing so can prevent the product from electrical short-circuit.
17. When not using the product over three(3) days,drain the water out of the container and pull the elelctrical plug from the wall outlet.
18. Stop using the product and shut off the power when product malfunctions,please contact the service people for professional service.

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
DANGER – Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
This product is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided — if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel.
SAVE THESE INSTRUCTIONS

TECHNICAL SPECIFICATION

pressure). Maximum water pressure 0.8MPa (Hydrostatic pressure)
Electrical wire| length is about 1.8m
Cleaning device| Container capacity| 600ml
Heating power| 1000W
Water temperature| 6 different level adjustment
Water volume| 5 different level adjustment
Cleansing mode| Rear cleaning/Rear massage,Front cleaning for ladies
Spray cleansing location| 5 different level adjustment
Water pressure protector| Pressure stabilize,Automatic pressure discharging
Anti-fouling device| Speedy water discharge device, Automatic nozzle cleaning, Anti-syphon device, Anti-backflow device, Filter device
Safety device| Temperature controller, Thermal fuse, Ground protection, Leakage protection device, Air burning preventer
Drying device| Warm wind speed| Over 4 M/S
Warm wind temperature| 6 different level adjustment
Heating power| 250W
Safety device| Temperature sensor, Temperature controller, Thermal fuse
Heated seat| Surface temperature| 6 different level adjustment
Heating power| 50W
Open and close device| Quiet soft-closing device
Heated burning protection| The seat temperature will automatically lower to level 1 in 10 minutes after using
Safety device| Seat sensor, Temperature sensor, Temperature controller, Thermal fuse
Intelligent| Night light assembly| Intellignt,often in the off state
Mute setting| Buzzeroff during night
User ID setting| To avoid disturbance from remote controls by multi-user

PACKAGING LIST

Remote
Control
Panel Parts| |
---|---|---
Base Plate
Parts| 1. Base plate|
2. Bolt (2pcs)
3. Flat Washer (2pcs)
4. Plastic Plate (2pcs)
5. Expansion Nut(2pcs)
Water Supply
Assembly| 1. Water Supply Pipe (lpcs)|
2. 3-way Connector (lpcs)
Installtion Manual
Warranty Card
Installation paperboard| Installtion Manual|
Warranty Card
Installation paperboard
Main Unit| |

MAIN UNIT IDENTIFICATION

INSTALLATION LNSTRUCTION

Installation dimension
Note: please check if the installation dimension matching the user’s toilet. Installation of mounting plate
Press the expansion nuts into the installation holes in the toilet,then install the base plate, plastic plates,flat washers and bolt as per the drawing and tighten the bolts. Note:
Unfold the installation paperboard,align the paperboard well fit ceramic bowl from the tip ,and then insert base plate to the paperboard breach to make sure base plate allign with paperboard breach.
Installation and disassembly of main unit

Installation
Push the bidet back onto the base plate until a “click” is heard.
Disassembly
Press the “removal button” on bidet, until a “click” is heard,and pull it out.

|
---|---

Connecting the water supply pipe

1. Side inlet: Install the 3-way valve onto angle valve,then attach the water supply hose and the bidet inlet hose into 3-way valve.Connect L-shaped end of water supply hose  to the bidet inlet connector. [ (a) and (b) parts not included in the water supply assembly. ]
2. Bottom inlet:Connect water supply on the inlet connector,then put supply hose and power line through the relevant holes, finally install seat cover.
   

Note:
Do not distort or damage the supply hose to avoid any leakage.
Do not use water supply hose and other accessories of other brands, which may cause danger.
Do not recommend to use our old water supply hose and accessories, which may cause danger.

Checking the power and water supply

Connect the water supply hose and turn on the angle valve.Check if any leakage.| Insert power line leakage protection plug into the power socket, press the reset switch, plug indicator lights on indicating that the power is on.
---|---
|
Tips:
Press electric leakage test button prior to usage, the reset switch  pops up indicating that the leakage protection function is normal.
Press the TEST button (then RESET button) every month to assure proper operation.
Suitable for the product with leakage protection plug.
Please refer to the actual product.
The main unit buzzer rings first “click”,
the power light and energy saver light will flash.
Power light on and energy saver light off means
self-inspection.| The buzzer rings second “click” to show that
self-inspection is finished.
|
The water starts to flow into tank and heating will take 3 minutes.

Function illustration of keys in main unit and actuator

| Power| 1. Long press “Power” button to enter standby mode;        and then quick press “Power”  button to restore functional mode.
2. When people sit, press “Power” button to stop the function of  rear, front cleaning or drying. When no one sits, press “Power” button to switch between function mode and power save mode.
---|---|---
Front cleaning
button| When people sit, press “Front cleaning” button, it will clean the front portion of body;  repress “Front cleaning” button or “Power” button, the function will be finished. After a  cycle, this function will be finished automatically, if people keep sit, it will switch to drying  function, and will stop after a cycle.
Rear cleaning
button| 1.When people sit, press “Rear cleaning” button, it will clean the rear portion of body; repress “Front cleaning” button or “Power” button, the function will be finished. After a cycle, this function will be finished automatically, if people keep sit, it will switch to drying function, and will stop after a cycle.
2.When no one sits,press “Rear cleaning” button,then the wand will stretch out to clean the nozzle and spray wand.

Remark:

1. When main unit is in functional mode, the light of power goes on and energy saver light is off; When in energy save function, the light of power goes off, and energy
   saver light is on; When in standby mode, both lights are off.

2. The default setting of all function is on middle level, after using remote-controller, shift to the level showing on remote-controller.

3. If the product is not used for continual 72 hours,the water in the tank will automatically discharge for 90 seconds and replaced by fresh water,to avoid bacteria.

Function illustration of keys in remote-control and LCD display instruction

• The operating method of remote control shows in instruction manual.

Main unit maintenance

1. Shut off power supply at maintenance.
2. Turn the seat upward open,press down the button located on the right side of main unit and pull out the seat.Wipe the stain with a soft damp cloth.
3. After cleaning,re-install the seat back to main unit.

Note:
Do not pour the water on the product at maintenance.

Spray nozzle maintenance
Do the following to clean the wand.

1. Press “nozzle cleaning” or “rear cleaning” button for a while and wand will come out.Wipe the wand clean with a soft damp cloth.
2. Hold “nozzle cleaning” button and the wand doesn’t come out.The nozzle will automatically spray to self-clean.
3. Press again “nozzle cleaning” or “stop” or “rear cleaning” button,it will stop the cleaning.
   

Note:
Do not apply force when pushing or pulling the wand,as this may damage the mechanism.

Inlet filter cleaning

1. Pull out electrical plug,then shut off water supply valve and remove water supply hose.
2. Remove the filter.Use the brush to clean the filter.
3. Put the filter back into inlet after cleaning.Then connect the water supply pipe.
   

Tank anti-freezing and anti-bacterial maintenance
When room temperature is under zero and electricity is disconnected,or user is away for a
long time.The water inside the tank should be discharged.

1. Open the tank cover,press the discharge button,turn on valve to discharge the water.
2. Slightly press the discharge button protruding part to turn off discharging valve and cover.
   

Note: Before water discharging, the power must be cut off!

pressure). Maximum water pressure 0.8MPa (Hydrostatic pressure)
Electrical wire| length is about 1.8m
Cleaning device| Container capacity| 600m1
Heating power| 1000W
Water temperature| 6 different level adjustment
Water volume| 5 different level adjustment
Cleansing mode| Rear cleaning/Rear massage,Front cleaning for ladies
Spray cleansing l  ocation| 5 different level adjustment
Water pressure protector| Pressure stabilize,Automatic pressure discharging
Anti-fouling device| Speedy water discharge device, Automatic nozzle cleaning, Anti-syphon device, Anti-backflow device, Filter device
Safety device| Temperature controller, Thermal fuse, Ground protection, Leakage protection device, Air burning preventer
Drying
device| Warm wind speed| Over 4 M/S
Warm wind temperature| 6 different level adjustment
Heating power| 250W
Safety device| Temperature sensor, Temperature controller, Thermal fuse
Heated seat| Surface temperature| 6 different level adjustment
Heating power| SOW
Open and close device| Quiet soft-closing device
Heated burning protection| The seat temperature will automatically lower to level 1 in 10 minutes after using
Safety device| Seat sensor, Temperature sensor, Temperature controller, Thermal fuse
Intelligent| Night light assembly| Intellignt,often in the off state
Mute setting| Buzzeroff during night
User ID setting| To avoid disturbance from remote controls by multi-user

Retain these installation instructions for future reference!
Thank you for using WoodBridge products!
INSTALLER INFORMATION

DATE OF INSTALL:
INSTALLER’S NAME:
PLUMBER: CONTRACTOR:
LICENSE #:www.woodbridgebath.com
Customer Service Phone: 562-229-0088. (Monday – Friday 9 AM – 5 PM Pacific Time)
Or Email: help@woodbridgebath.com
www.woodbridgebath.com

References

• ᐅ【One Piece Toilets | Freestanding Bathtubs | Shower Bases | WOODBRIDGE】

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>