OLIGHT Arkfeld Dual Light Source EDC Flashlight User Manual

OLIGHT Arkfeld Dual Light Source EDC Flashlight

IN THE BOX

SPECIFICATIONS

All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the product.

Note: The maximum output brightness will decrease as the battery voltage decreases

USB MAGNETIC CHARGING CABLE — MCC1A

Parameter     Specification

• Charging cable  USB type A – magnetic charging connector Length: 0.5m

• Input USB A-Type DC 5V 1A

• Charging pattern CC&CV

• Maximum charging current 1A

• Voltage of fully charged battery  4.2V±0.05V

• Time to fully charge
  3.5 hours (For reference only. When the USB power source is insufficient to provide 5V 1A power capacity, the charging time will be longer.)

• Charge indication
  Red: charging
  Green: fully charged or disconnected

PRODUCT OVERVIEW

BEFORE FIRST USE

THE PRODUCT IS SHIPPED IN LOCKOUT MODE. PLEASE CHARGE IT TO UNLOCK.

CHARGING

• Before first use please fully charge the product.
• Connect the USB end of the magnetic charging cable to an external USB power source, then attach the other end of the cable to the charging port of the light (best charging efficiency with a USB power source of no less than 5W (5V 1A) . The red indicator means charging, while the green indicator means charging complete

PRODUCT INSTALLATION

1. Unscrew and remove the socket screw and washer with the included Allen wrench.
2. Slide the rail mount of the product along the Picatinny rails into the desired position.
3. Insert the socket screw and washer back in place across the rail mount, and tighten with the included Allen wrench.

Note: For mounting on M-LOK rails, please install a section of Picatinny rails on the M-LOK rails as the installation adapter.

CAUTION

• DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
• DO NOT cover the product when its light is on. The heat built-up may cause close objects to burn.
• DO NOT charge the product in any other way than using the included MCC1A cable and the compatible MCC3 cable.
• DO NOT store the product in the car or any place where the temperature may exceed 60℃.
• DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature.
• Hot surface warning: DO NOT touch the surface of the product marked with the icon, otherwise it may burn your skin.
• DO NOT clean the lens with alcohol or any other chemicals.

NOTICE

• DO NOT disassemble the product.
• DO NOT short-circuit the charging port at the tail.
• Active thermal management: The built-in thermal sensor will monitor the temperature of the product in real time. When the temperature reaches the threshold, the output will be reduced to prevent overheating.
• If the product is about to be put aside for a long time or be transported, please lock out the switches to avoid accidental activation.

REMARK

• Please fully charge the battery before storing the product for a long period of time.
• The brightness will be capped at 290 lumens if the battery voltage is low.
• Please keep the charging port at the tail clean and dry.
• At room temperature, the white light is only able to provide 1,450 lumens for 2 minutes. After that, it gradually steps down to 480 lumens within the next 30 seconds.

EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.

HOW TO OPERATE

CONSTANT ON/OFF: Single press either side switch for constant on. Single press again to turn it off.
MOMENTARY ON: Press and hold down either side switch for momentary on. Let go of the switch and it will turn off.
CHANGE BRIGHTNESS: When the light is turned on, quickly double press either side switch to change between high white light and low white light. When the light is turned on again, it will return to the previously used light setting.
HIGH WHITE LIGHT: When the light is turned off, quickly double press either side switch to access the high white light setting directly.
LOCK/UNLOCK: When the light is turned off, press and hold either side switch for about half a second, then press and hold the other switch at the same time for about two seconds to access the lockout mode (the light will turn on momentarily and then turn off to signal the lockout mode). In lockout mode, press either side switch and the light will temporarily turn on with a dim white light (about 100 lumens). To leave lockout mode, press and hold both switches at the same time for about 2 seconds until it accesses the low white light setting.
NOTE: The high setting will only be memorized for 1 minute. After that, the memorized setting will revert to low.

Within 30 days of purchase: Contact the original seller for repair or replacement.
Within 2 years of purchase: Contact Olight for repair or replacement.

USB magnetic charging cable: One year.
For any of the fragile or low-value fittings not covered above, you can contact the post-sale within 30 days of the purchase, if it has any quality drawback or damage under normal use condition. If such drawback or damage occurs after 30 days of the purchase or under abnormal use condition, we will only offer conditional quality assurance as appropriate.

USA Customer Support
cs@olightstore.com

Global Customer Support
customer-service@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.

EU-Declaration of Conformity can be found here: https://olightworld.com/ec- declaration

References

• Olight | Illuminate Your World.
• Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>