Quay Design 3012536 Layla LED Ceiling Light Instruction Manual
- June 13, 2024
- QUAY DESIGN
Table of Contents
Quay Design 3012536 Layla LED Ceiling Light
Product Information
The product is a pendant light designed for indoor use. It is manufactured by Poole Lighting Ltd. The company has a UK address at atBH17 7BY and an EU address at Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg.
Safety Warnings
- Ensure there is a solid mounting surface, preferably a wooden joist or joist bridge, to support the weight of the light.
- The electric cable must always be longer than the chain to prevent strain.
- Allow 10 minutes for the light to cool before replacing, adjusting, or cleaning.
- Turn off the power before installation or maintenance.
- Follow all applicable electrical safety guidelines and regulations.
Care Information Before performing any maintenance on the light, allow it to cool for at least 10 minutes. Use a soft cloth and mild cleaning solution to clean the surface. Do not use abrasive cleaners or solvents.
Parts List
Qty | Part No. |
---|---|
18 | G |
36 | H |
36 | E |
18 | F |
Required Tools
- Electric drill and assorted drill bits
- Wire strippers
- Electrical insulation tape
Product Usage Instructions
- Ensure there is a solid mounting surface, preferably a wooden joist or joist bridge, to support the weight of the light.
- Make sure the product is fully assembled as illustrated in the manual before use.
- Allow the light to cool for at least 10 minutes before replacing, adjusting, or cleaning.
- If necessary, use the provided tools (electric drill, drill bits, wire strippers, electrical insulation tape) for installation.
- Connect the terminal blocks according to the diagram provided in Figure 1.
- Ensure the electric cable is longer than the chain to prevent strain.
- Turn on the power and test the light to ensure it is functioning properly.
- Adjust the light level using the controls indicated in Figure 2. There are seven levels available.
- Follow the care information provided to clean and maintain the light.
Safety Warnings
- This product is only suitable for connection to a 240V~50Hz supply in accordance with current IEE wiring regulations. It should be installed in accordance with local building regulations and is for domestic ceiling use only. It is not suitable for a bathroom location.
- Before installing your light fitting always switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker before commencing installation.
- This is a Class II, Double Insulated product This fitting does not require an Earth, and Live or Neutral must! be connected to Earth. The terminal blocks are supplied according to the requirements of the fitting.
- Never fit bulbs of a higher wattage than those specified on the label, as these may cause overheating and damage the fitting.
- If you are in any doubt about your competence please consult a qualified electrician.
- If any modification is made it will invalidate the warranty and may render the product unsafe.
Care Information
- Allow 10 minutes to cool before replacing, adjusting, or cleaning.
- Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Assembly/ User Instructions
Before you start
Please read these instructions carefully before fitting and retain them for
reference. Check the packaging and make sure that you have all the required
parts. Follow each assembly step in order to prevent incorrect assembly.
Ensure that the product is fully assembled as illustrated before use.
The Light pack contains:
- Light fitting.
- Terminal connection block(s).
- Fixing pack.
- Decorative rods, as shown below.
The following tools may be required:
- Electric drill and assorted drill bits.
- Wire strippers.
- Electrical insulation tape.
These assembly diagrams are intended as a guide — if in doubt consult a qualified electrician.
-
Decide on the position of the light fitting, or remove the existing light fitting. Note the position of the electrical connections. Ensure there is a solid mounting surface, preferably a wooden joist or joist bridge to support the weight of the light fitting.
-
If you want to reduce the overall length of the fitting it is essential that this is done before the fitting is mounted to the ceiling, or connected to the mains supply. Remove the chain links until the desired length is reached. The cable must now be shortened and the excess cable cut and re-connected to the terminal block. Feed the cable up through the plastic bush and form a loop above the ceiling cup, moving the figure of 8 cable restraint down the exposed cable. NOTE: The electric cable must always be longer than the chain to prevent strain from being placed on the cable. If you are unsure about your ability to do this. we recommend you contact a qualified electrician.
-
Fit the bulbs, being careful not to touch it with your bare hands – use a cloth or gloves.
NOTE : Never fit bulbs of a higher wattage than those specified on the label. -
Assemble the decorative rods, as shown in Figure 1. Fit levels 1-4 prior to hanging.
-
Referring to Figure 2, remove the two side screws (4) and retain for re-use. Use the fixing bracket (1 ) as a template to mark the screw holes. Make the screw holes and secure to the ceiling with appropriate screw fixings (2).
-
Support your fitting and connect the house wiring to the terminal block (3) — see expanded wiring details below.
NOTE : This is a Class II fitting and must NOT be earthed. Any loose terminal blocks — not secured to ceiling cup — should always be covered with 2 layers of good-quality insulation tape. -
Secure the ceiling cup over the bracket by using the screws (4) removed in Point 5.
-
Fit decorative rods levels 5-7, per figure 1
-
Turn on the power and test.
Scan the QR code for multi-language
Manufactured by: Poole Lighting Ltd.
UK: BH17 7BY
EU: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>