GLITNOUS BLA00361100 Solar Barn Light with 3 Lighting Modes User Manual

GLITNOUS BLA00361100 Solar Barn Light with 3 Lighting Modes

PLEASE CONTACT: support@glitnous.com

SPECIFICATIONS

HOW SOLAR LIGHT WORKS

During the day, the solar panel converts solar power into the rechargeable the battery. At night, the light turns on automatically by the stored energy.
The time of the light lasts to illuminate depends on your geographical location, weather conditions and seasonal light availability.

CHOOSING AN IDEAL LOCATION TO INSTALL

Choosing an outdoor location with full, direct sunlight where the Solar Panel can receive at least 6 hours of sunlight each day.
Shady locations will interfere with charging the batteries with enough energy and shorten the working time of night lighting.
The selected location should not be near strong lighting sources such as street lights, which may cause the solar barn light to turn off automatically because there is a sensor inside to sense the brightness and control the lights work.

ATTENTION FOR FIRST TIME USE

There is a switch on the above the motion sensor. Please make sure to turn on the switch and keep it on at all times so that the solar light will auto charging during the day and auto light up at night.
When the environment becomes dark, the solar light will light up automatically. During the day, the solar light will automatically turn off and store energy from the solar panel.
If the light does not turn on automatically at night after 6 hours of charging.

please check the following:

1. To make sure the power switch is turned on.
2. To check if the bulb is loose and make sure that the bulb and socket are installed in a good match.
3. To be sure that light is in a sunny location and the solar panel is facing to the sun, not in a shady area.

The product installation includes

1. E26 light bulb
2. The lamp shape with E26 socket
3. Gooseneck pole
4. Butterfly screw
5. The lamp holder
6. Screws for fixing lamp stand
7. User Manual

Auxiliary tools that may be used during installation: Impact drill/ Hammer / Wrench / Screwdriver

1. Assemble the gooseneck pole and lamp holder with a butterfly screw and make sure the installation is firm.
   

2. Fix the lamp shape on the gooseneck pole with a screw and make sure the installation is firm. (Note: The motion sensor should be facing outward.)
   

3. Drill three holes on the wall corresponding to the location of the light holder holes, and put the 3 expansion bolts in these three holes.
   

4. Fix the main body of the lamp on the wall with 3 screws in the accessory package and make sure the installation is firm.
   

5. Install the light bulb to the standard E26 socket and then turn on the solar light by pressing the switch.
   

6. The installation finished!
   

3 LIGHTING MODES

Select lighting mode by pressing the button above the sensor.

1. Mode (1) 40%-100%-40%: auto standby at 40% brightness light at dusk, 100% brightness when detect motion, standby after 20s without motion.
2. Mode 2) OFF-100%-OFF: only lights up when motion is detected, and auto goes out after 20s without motion.
3. Mode 3) Auto light up and maintains 40% brightness at dusk, unaffected by movement.

PRECAUTIONS

1. Please note that the light works when the environment becomes dark.
   If there is a strong light source nearby, the solar barn light may be very dim or not work at all.

2. Although the battery has been charged by the manufacturer, the power level may probably drop when you receive it.
   Please charge it for a full day for maximum performance.

3. The surface of the solar panel must be kept clean.
   If it is dusty, it will affect the charging efficiency.

4. Install the solar lights in a place where there is enough sunlight.
   The operating hours may vary due to occasional rainy days and cloudy days or the lighting being blocked by trees, houses, etc.

5. If the unit does not work due to over-discharge, please charge it for a full day to make it work again.

REMARKS

1. Clean the solar panel: It is important that the solar panel is kept free of dirt, debris or even snow as this will affect the battery to fully recharge, resulting in the solar barn light cannot stay on, sense and light up. This could also shorten the life of the battery. Clean regularly with a dampened cloth or paper towel
2. Recycle used solar power battery or dispose of them properly. Please do not puncture, short circuit, or dispose of in fire.

If you encounter any problems during installation or use, please kindly contact us through the following email address, we will help you solve the problem in time.
Email: support@glitnous.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>