OLIGHT RN 2000 Wireless Remote Controlled Bicycle Headlight User Manual

OLIGHT RN 2000 Wireless Remote Controlled Bicycle Headlight

• Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!

IN THE BOX

SPECIFICATIONS

The tests are performed indoors under a room temperature of 25 degrees Celsius with 25KM/H

HOW TO INSTALL

BEFORE FIRST USE

• The bike light arrives in lockout mode.
• Before first use, please unlock the light.
• If the light is left unused, carried, or transported, please lock out the power button to prevent potential damage from the heat built up due to accidental activation.
• Lock: When the light is off, press and hold the power button for about 3 seconds until the indicator flashes red.
• Unlock: When the light is locked, press and hold the power button for about 3 seconds until the indicator turns constant red.

HOW TO RECHARGE

Standard Charging Time: Approx.3.5hrs (5V 2A)

BATTERY INDICATOR

• When the device is powered on, the indicator on the power button will indicate the battery level.
• When the device is powered off, short press the power button to activate the indicator light (light will shut down automatically after 3 seconds.

PHONE CHARGING INSTRUCTION

Note: Charging cables need to be purchased separately.

DANGER

• DO NOT shine the light directly into human eyes. This may cause temporary blindness or permanent damage to the eyes.
• DO NOT cover the light head when the bicycle light is on, or place the bicycle light head on the ground.
• The radiation energy of the bicycle light may cause damage to the bicycle light itself, or even result in the burning of flammable objects.

WARNING

• Keep out of reach of children.
• The light contains a lithium-ion battery. Certain restrictions may apply to this product when traveling, especially when traveling by air.
• Always check with your carrier for specific restrictions before traveling with this product.
• DO NOT clean the lens with alcohol or any other chemicals.

NOTICE

• Store the light at room temperature in a dry place. Avoid moisture, or extreme heat or cold.
• Store the light in the charged condition. Avoid “deep discharge”. Battery life will decrease if the light is stored in a fully discharged condition.
• Over time, the run time of the battery will diminish, Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time.
• When the run time is unsatisfactory, please recycle. DO NOT open the case of the light or incinerate.

EXCLUSION CLAUSE

• Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode.

OPERATING INSTRUCTIONS

REMOTE CONTROL PAIRING

• Before using the remote control, please remove the insulating spacer and reinstall the battery.
• Turn on the light, press and hold the “o” and “o” buttons on the remote for about 10 seconds until the indicator alternately flashes blue to enter pairing mode.
• Then, close the remote to the light until the indicators on the remote and light unit are constantly blue for 2 seconds, confirming a successful pairing.

REMOTE CONTROL OPERATION

• ON/OFF: Press and hold the “o”/”•” button for 1 second
• ADJUST BRIGHTNESS: Click the “o” button
• CHANGE MODE: Double-click the “o” button
• FLASH MODE: Double-click the “o” button
• FULL OUTPUT MODE (2000LM): Click the “o” button to go into full output mode and click the “o”/”•” button to return to the previous mode.
• The remote control will enter sleep mode if the light is turned off for 48 hours without any operation.
• Click the light’s button to activate it or long-press the light’s button to turn it on, and the remote control can work normally.

HEADLIGHT BUTTON INSTRUCTIONS

• ON/OFF: Press and hold the button to turn the light on/off. The default output is the last mode when turned off.
• ADJUST BRIGHTNESS: Click the “^” button to increase the brightness, and click the “~” button to decrease the brightness.
• CHANGE MODE: Double-click the button to change between floodlight mode and hybrid mode.
• LOCKOUT: When the light is off, press and hold the button for 3 seconds to enter lockout mode. (In lockout mode, the light will not light up and the indicator flashes red quickly)
• UNLOCK: In lockout mode, press and hold the button for 3 seconds to unlock the light.
• SMART MODE: The smart mode is off by default; double click and long press for 3 seconds to turn it on/off. In smart mode, the light will automatically go out after 2 minutes of inaction and light up on any vibrations.
• The light will automatically switch off if no vibration is detected within 30 minutes. During the daytime, the light will automatically turn to the LOW brightness of floodlight mode.
• At nighttime, the light will automatically return to the brightness that it’s in when turned on.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

WARRANTY

• Within 30 days of purchase: Return to the original seller for repair or replacement.
• Within 2 years of purchase: Return to Olight for repair or replacement.
• This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an authorized retailer or Olight itself.
• USA Customer Support cs@olightstore.com
• Global Customer Support contact@olightworld.com
• Visit www.olightworld.com to see our complete product line of portable illumination tools.
• Dongguan Olight E-Commerce Technology Co., Ltd 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road,
• Changan Town, Dongguan City, Guangdong, China.
• Made in China
• FCC ID: 2A3J6-MJ6508REMOTE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>