OLIGHT M-Lok Mini 1250 Lumens Ultra Compact Rechargeable Mlok Mount Tactical Flashlight User Manual

OLIGHT M-Lok Mini 1250 Lumens Ultra Compact Rechargeable Mlok Mount

Tactical Flashlight

Product Information

Specifications:

• CCT: 5700K
• CRI: 70
• HIGH Mode:
  • 1500 lumens at 100%
  • 3.5 minutes runtime
  • 43% output for 110 minutes
• LOW Mode:
  • 300 lumens at 100%
  • 5 hours and 10 minutes runtime
  • 20% output for 18 minutes
• Self-Locking Band
• Beam Distance: 250m
• Impact Resistance: 1.5m
• IPX8 Waterproof Rating
• Dimensions: (L)127.5(D)29mm or (L)5.02(D)1.14in
• Rechargeable Li-ion Battery: 3500mAh, 3.6V (12.6Wh)
• Weight: 193g/6.81oz (Including Batteries)

Product Usage Instructions

Battery Installation:

1. Remove the insulating film from the battery holder before use.
2. Install two CR123A batteries into the battery holder, ensuring correct polarity.

Rail Mount Installation:

1. Loosen the screws on the rail mount and position it as desired.
2. Tighten the screws to secure the rail mount in place.

Rail Mounted Light Installation:

1. Loosen the knob locking lever on the rail mount.
2. Adjust the width of the rail mount opening.
3. Place the T-mount on the product into the rail mount.
4. Tighten the knob locking lever to secure the light in place.

Remote Switch Installation:

1. Attach the remote switch to the tail of the product and turn the ring clockwise to fix it.
2. To remove the remote switch, turn the ring counter-clockwise and pull until you hear a click.

FAQ:

• Q: How do I switch between High and Low modes?
  A: For Constant On mode, press the HI button for High mode and LO button for Low mode. For Momentary On mode, press and hold the HI or LO button, then release to turn off the light.

• Q: How do I know when charging is complete?
  A: The charging cable indicator will show a green light when charging is completed, and a red light during charging.

• Q: How do I enable/disable the Strobe function?
  A: Quickly press the switch five times or more, then hold it for more than 1 second at the last press to enable/disable the Strobe function.

IN THE BOX

Product specifications

Remove the insulating film before use

Charging

Use the battery holder

Product installation

Rail mount installation, see Figure 4.
Loosen the screws, install the rail mount in the desired position, and then tighten the screws.

Rail mounted light installation, see Figure 5.
Unscrew the knob locking lever on the rail mount counterclockwise until it stops. Push the knob locking lever to adjust the width of the rail mount opening. Place the T-mount on the product into the T-shape inside the rail mount, ensuring that the two screws on the rail holder align with the slots in the product’s T-mount. Lastly, lock the knob locking lever on the rail mount by turning it clockwise using a tool.

Light removal, see Figure 6.
To remove the product, loosen the knob locking lever on the rail mount and push it to adjust the width of the rail mount opening.

Tail switch operating

Constant On.

1. Low mode, see Figure 7.
   Press lightly and quickly for Low mode, and press again to turn it off.

2. High mode, see Figure 8.
   Press hard and quickly for High mode, and press again to turn it off.

Momentary On:

1. Low mode, see Figure 9.
   Press lightly and hold for Low mode, and release to turn it off.

2. High mode, see Figure 10.
   Press hard and hold for High mode, and release to turn it off.

Switch to High mode, see Figure 11.
In Low mode, single press or heavily press and hold the switch for High mode.

Enable/disable the Strobe function, see Figure 12.
When the light is off, press the button hard five times (or more) quickly, and hold it for more than 1 second at the last press, then the Strobe can be enabled or disabled.

Turn on/off the Strobe, see Figure 13.
Double (or more) press the button hard quickly to turn on the Strobe, and press once again to turn it off.

Remote switch installation

To install the remote switch, first, push the detent ring towards the tail of the light, and then screw the ring clockwise. To remove the remote switch, simply screw the detent ring counterclockwise until you hear a click.

Remote switch operating

Constant On, see Figure 15.
Press the LO/HI button quickly for Low mode /High mode, and press again to turn it off.

Momentary On, see Figure 16.
Press and hold the LO/HI button for Low mode /High mode, and release it to turn the light off.

Enable/disable the Strobe function, see Figure 17.
When the light is off, press the HI button five times (or more) quickly, and hold it for more than 1 second at the last press, then the Strobe can be enabled or disabled.

Strobe (when Strobe function is activated), see Figure 18.
Double (or more) press the HI button quickly to turn on the Strobe, and press once again to turn it off.

WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, to protect human health and the environment, you should dispose of your waste equipment at a designated collection point for the recycling of WEEE, appointed by the government or local authorities. Proper disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED Notice
This device complies with Industry Canada’s licence-exempt ICES standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

EU Declaration of Conformity
Dongguan Olight E-Commerce Technology Co,Ltd declares that the equipment [Odin S] complies with Directive 2014/30/EU and RoHS Directive 2011/65/EU & (EU) 2015/863. The full text of the EU declaration of conformity is available at the following internet address: https://www.olight.com/download

WARRANTY

We are proud to offer a lifetime warranty in Australia, China, France, Germany, and the USA. We are also working hard to expand coverage to more countries, where we provide a 2 or 5-year warranty. The warranty covers defects in material and workmanship under normal use, excluding loss, theft, deliberate damage, or cosmetic damage. For complete warranty information, please visit Olight.com or your local Olight official website.

• Australia Customer Support: contact@olightstore.com.au
• Austria Customer Support: kontakt@olightstore.at
• Canada Customer Support: cs@olightstore.ca
• China Customer Support: Wechat: olightcs
• France Customer Support: cs@olightstore.fr
• Germany Customer Support: kontakt@olightstore.de
• Italy Customer Support: contatto@olightstore.it
• Japan Customer Support: cs@olightstore.jp
• Korea Customer Support: olightkorea@olight.com
• Spain Customer Support: contacto@olightstore.es
• Thailand Customer Support: cs@olightstore.co.th
• UK Customer Support: contact@olightstore.uk
• USA Customer Support: cs@olightstore.com
• For other countries and regions, please contact Global Customer Support: contact@olight.com

Dongguan Olight E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.
Made in China

References

• Olight | Illuminate Your World.
• Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>