BRAYER BR3007 Hairdryer Instruction Manual

: June 3, 2024
: BRAYER

Table of Contents

HAIRDRYER BR3007
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
USING THE HAIRDRYER
OVERHEATING PROTECTION
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
Documents / Resources

Instruction manual

HAIRDRYER BR3007

The hairdryer is intended for hair drying and styling.
DESCRIPTION

Operation mode switch (0/ / )
Air flow temperature switch
«Cool shot» button « »
Nozzle
Body
Air inlet grid
Foldable handle
Hanging loop

ATTENTION!

Do not use the unit near water in the bathrooms, showers, swimming pools etc.
After using the hairdryer in a bathroom, you should take the power plug out of the mains socketas closeness of water is dangerous even if the unit is switched off.
For additional protection it is reasonable to installa residual current device (RCD) with nominal operation current not exceeding 30 mA into the mains of a bathroom. To install it, contact an electrical technician.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation manual carefully before using the unit; after reading, keep it for future reference.

Use the unit for its intended purpose only, as specified in this manual.
Mishandling the unit can lead to its breakage and cause harm to the user or damage to his/her property and it is not covered by warranty.
The hairdryer is intended only for styling of slightly wet and dry hair, do not use the unit for styling of wet hair or synthetic wigs.
Make sure that operating voltage of the unit indicated on the label corresponds to your home mains voltage.
Do not use the unit when you are drowsy.
Do not use the unit outdoors
It is not recommended to use the unit during lightning storms.
Protect the unit from blows, drops, vibrations and other mechanical stress.
Never leave the plugged-in hairdryer unattended.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in places where aerosols are used or sprayed and close to inflammable liquids.
Do not use the unit near a kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
Do not use the unit while taking a bath.
Do not hang or keep the unit in places where it can fall into a bath or a sink filled with water; do not immerse the unit body, power cord or power plug into water or other liquids.
If the unit is dropped into water, unplug it immediately; only then take the unit out of the water.
Do not let the power cord touch hot surfaces and sharp edges of furniture.
Unplug the unit after usage or before cleaning. When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
Do not touch the mixer body, the power cord and the power plug with wet hands.
Avoid contact of heated surfaces with your face, neck and other parts of your body.
Do not direct hot air into your eyes or other heatsensitive parts of your body.
The attachment gets hot during operation. Allow it to cool down before removal.
Never insert any foreign objects into any unit body openings.
Do not block the air inlets of the hairdryer, do not place it on a soft surface, where the air inlets may be blocked. Keep the air inlets free of lint, dust and hair etc.
Clean the unit regularly.
Unplug the unit after usage and before cleaning.
For child safety reasons do not leave polyethylene bags used as packaging unattended.

ATTENTION!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!

The hairdryer is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, unit body, power cord or power plug during operation of the unit.
Close supervision is necessary when children or disabled persons are near the operating unit.
During the unit’s operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
Regularly check the integrity of the power cord.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or by similar qualified personnel, to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself; in case of any malfunction or if the unit is dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in original package only.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative temperature, unpack it and wait for 3 hours before using it.

Unpack the unit and remove all the packaging materials.
Keep the original package.
Check the delivery set.
Read the safety measures and operating recommendations.
Examine the unit for damages; if the unit is damaged, do not plug it into the mains.
Make sure that the indicated specifications of the power supply voltage of the unit correspond to the specifications of your mains. When the unit is powered from 60 Hz frequency mains, no additional actions are necessary.

USING THE HAIRDRYER

Make sure that the operation mode switch (1) is set to the position «0».
Unwind the power cord completely.
Insert the power plug into the mains socket.
Use the switch (1) to set the required operation mode:
– «0» — the hot air styler is switched off;
– « » — warm air supply;
– « » — hot air supply.
The button (3) is the cool shot function « », press and hold down the «cool» shot button for fixing your hairstyle.
Note: — during the first operation a foreign smell and a small amount of smoke can appear from the heating element, this is normal and it is not covered by warranty.
– After unit operation, switch the hairdryer off by setting the switch (1) to the position «0», and unplug it.

NOZZLE

Use the nozzle (4) when you need to focus the power of drying on a small area (for example, a curl or a wave) or when you want to straighten wavy hair.
Attach the nozzle (4) to the unit body. The nozzle (4) allows directing a narrow air flow of high intensity at a definite hair lock.
Insert the power plug into the mains socket. Use the switch (1) to set the necessary operation mode.
When the desired effect is achieved, press the cool shot button (4) and fix your hairstyle.
Periodically straighten the power cord if it gets twisted during operation.

OVERHEATING PROTECTION

Overheating protection switches the hairdryer off if the outgoing air is too hot.
If the hot air styler is switched off during operation, set the switch (1) to the position «0», unplug the unit and make sure that the air inlets and outlets are unblocked.
Let the unit cool down for 5-10 minutes and switch it on again. Do not block the air inlets during operation of the hot air styler and
avoid getting of hair into the air inlet grid (6).

CLEANING AND MAINTENANCE

The hairdryer is intended for household use only.
Set the switch (1) to the «0» position, disconnect the hairdryer from the mains and let it cool down.
Wipe the unit body (5) with a slightly damp cloth, and then wipe it dry.
Press the grid (6) on both sides and take it off. Clean the air inlet grid (6) with a brush. Install the grid (6) back to its place until locks clicking.
Do not immerse the unit into water or any other liquids.
Do not use abrasives and solvents to clean the nozzle (3) and the unit body (4).

STORAGE

Disconnect the unit from the mains and clean it.
Never wind the power cord around the hairdryer body (4), as it can lead to its damage or damage of the unit body (4).
A hanging loop (7) you can hang the hairdryer on is provided for the ease of storage of the unit, given that no water will get on it; and you can fold the handle (6) to minimize the hairdryer size.
Keep the unit in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Hairdryer — 1 pc.
Nozzle — 1 pc.
Manual — 1 pc.

TECHNICAL SPECIFICATIONS

Supply voltage: 220-240 V, ~ 50/60 Hz
Rated input power: 2200 W

ATTENTION!
Do not use the unit near water in the bathrooms, showers, swimming pools etc.

RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the design, structure and specifi-cations not affecting general operation principles of the unit, without prior notice.
The unit operating life is 3 years The manufacturing date is specified in the serial number. In case of any malfunctions, it is necessary to apply promptly to the authorized service center.

Hergestellt für «Ruste GmbH»,
Berggasse 18/18, 1090 Wien,
Osterreich
Produced for «Ruste GmbH»,
Berggasse 18/18, 1090 Vienna, Austria
т.: +7 (495) 297-50-20,
e-mail: info@brayer.su
Made in China Hairdryer BR3007
Фен BR3007