BATAVIA BT-CDA001 Cordless Drain Auger Instruction Manual

BATAVIA BT-CDA001 Cordless Drain Auger Instruction Manual

Overview

1. Flexible shaft
2. Forward/neutral/reverse lever
3. Rotating direction switch
4. On/off trigger switch
5. Battery (not included in delivery)
6. Storage drum for the flexible shaft
7. Work light

Dear customer
Please familiarize yourself with the proper usage of the device by reading and following each chapter of this manual, in the order presented. Keep these operating instructions for further reference.

Please read the enclosed “General safety instructions for power tools” and all additional safety instructions in this operating instructions!
This manual contains important information on operating and handling the device.
Keep these operating instructions for further reference. Please pass it on along with the unit if it is handed over to a third party.

Battery and charger not included!
The battery available separately under art.
No: 7062517 (2Ah) or 7062518 (4Ah).
The charger available separately under art.
No: 7062519.

These items are available online and in participating stores.

Explanation of the symbols

The following symbols are used in the user manual or on the product:

Warning! To reduce the risk of injury, the user must read the instruction manual.

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Wear safety glasses. When working with electric power tools, sparks, splinters, chips and dust particles may be generated and these can cause loss of sight.

Variable speed control.

CE stands for “Conformité Européenne”, which means “In accordance with EU Regulations”.
With the CE marking, the manufacturer confirms that this Electric tool complies with the applicable European directives.

Do not dispose of electric power tools with domestic refuse.

Additional safety instructions for cordless drain augers

1. Wear protective goggles and a face mask to protect yourself from the possibly poisonous and infectious contents of the drain.

2. Wear tight-fitting, solid gloves made from coated fabric which can not get caught in the flexible shaft. Severe injury may result from hands or fingers being drawn into the flexible shaft. If necessary wear protective gloves made from rubber or latex under your gloves.

3. Please keep in mind that chemical drain cleaners are caustic, wear protective equipment if such agents were used before the drain auger!

4. Do not eat, drink or smoke while operating the drain auger. After work clean your hands and other body parts which have come in contact with the contents of the drain or other contaminations with soap and warm water before eating, drinking or smoking. This way you avoid taking on toxic or infectious material.

5. Severe injury to fingers, hands, arms or other body parts may result from clothes or gloves being drawn into rotating parts. Therefore wear tight-fitting clothing and if necessary a hair net. Do not wear jewellery or other items which my get caught in the flexible shaft.

6. Do not use soft gloves or rags to guide the rotating flexible shaft. Severe injury may result from them being twisted into the flexible shaft. Grasp the flexible shaft only with suitable, tight-fitting gloves. Unsuitable gloves may get caught in the flexible shaft and cause severe injury.

7. Hold the machine as close as possible to the entry of the drain or pipe you are cleaning to avoid that the flexible shaft may twist or form loops. An excessively long free piece of the flexible shaft may twist and snap and cause severe injury.
   Hold the machine as close as possible to the drain or pipe you are cleaning. If the machine can not be held close to the entry use a guide hose. If the distance is too great that may cause the flexible shaft to twist and snap.

8. In case the flexible shaft is blocked immediately stop the machine. Otherwise the flexible shaft may be overstressed and get out of control, snap or twist. That may cause severe injury.
   Always use the reverse gear to free the flexible shaft.

9. Machine and flexible shaft must be controlled by the same person. In case the flexible shaft is blocked the operator must be able to immediately stop the machine, so the flexible shaft can not kink, twist or snap.

10. Do not operate the machine in reverse gear. The reverse gear is only intended to free the flexible shaft in case or it being blocked.

11. This machine is intended only for cleaning drains and pipes. All other uses are forbidden.

12. Periodically check all nuts, bolts and other fixings and tighten where necessary.

Before first use

Remove the machine and the accessories from the packaging. Check the machine for transport damage and do not use the machine in case of damages. Keep the packing materials away from children, risk of suffocation!

Contents of packing

1× Cordless drain auger
1× Operating instructions

Intended use

This portable, battery-powered drain auger is intended for removing stubborn blockages in drains and pipes.

Setting the rotation direction

The machine is equipped with two operating elements, a forward/neutral/reverse lever and a rotating direction switch.
To unblock a drain use the machine in clockwise rotation. To do so set the rotating direction switch (3) so that the end left end marked with R is proud of the machine.
When the machine is started with the trigger switch (4) the shaft (1) rotates, seen from your side, clockwise. When you push the forward/neutral/reverse lever (2) forward the flexible shaft is driven forward out of the machine. In neutral position of the lever the shaft rotates but is not fed in any direction and when the lever is pulled back the shaft is retracted into the machine.
The reverse (counter clockwise) operation of the machine is used for freeing up a blocked flexible shaft. To do so, set the rotating direction switch (3) so that the right end marked with L is proud of the machine.
When the machine is started with the trigger switch (4) the shaft rotates, seen from your side, counter clockwise. When you push the forward/neutral/reverse lever (2) forward the flexible shaft is retracted back into the machine.

In neutral position of the lever the shaft rotates but is not fed in any direction and when the lever is pulled back the shaft is driven forward out of the machine.

Further notes on unblocking a drain

Remove the drain trap, if present. Also remove further sliding pipework of the drain if present.
Do not wear loose–fitting clothing or jewellery which may get caught in the flexible shaft. If you have long hair wear a hair net.

Do not use loose work gloves which may get caught in the shaft. Protect your hands with tight-fitting coated fabric gloves and if necessary, wear latex or rubber gloves under these.

Always bring the machine as close as possible to the entry of the pipe. If this is not possible run the free part of the shaft through a suitable piece of hose for handling.

Please keep in mind that the content of a drain is infectious and may contain caustic drain cleaners. Wearing safety glasses and a mouth or face protection is mandatory!

WARNING: If the device does not perform as outlined in this manual, turn to the Batavia customer service or to a competent professional.

Work light

The work light (7) illuminates the working area during operation.
When the trigger switch (4) is pressed the work light (7) turn son. When the trigger switch is released the work light turns off after approximately five seconds.

Cleaning and maintenance

WARNING: Remove the battery before carrying out any maintenance/cleaning of the tool

Cleaning

• Clean the flexible shaft with warm water and some detergent and allow it to fully dry in extended condition. After drying lightly oil the flexible shaft.

• Use only a moist cloth to clean the unit.
  Do not use aggressive chemicals which may dissolve plastic parts, or abrasives.
  Always keep the ventilation slots clean and free from obstructions.

• Keep safety devices, ventilation openings and the motor housing as free as possible from dirt and dust. Rub the electric power tool with a clean cloth or blow over it with low pressure compressed air.

• We recommend that you clean your electric power tool immediately after each use.

• Clean the electric power tool regularly with a damp cloth and somewhat soft soap.

Maintenance

There are no inner parts of the tool which need maintenance.

Technical data

No load speed . . . . . . . . . . 0 – 560 min-1
Dredging capacity . . . . . . . ø 19 – 50 mm
Length of flexible shaft . . . . . . . . . . .7 m
Working length . . . . . . . . . . . . . . 6.8 m
Diameter of shaft / shaft head . ø 7 / 12 mm
Product weight without battery . . . .3.46 kg
Product dimensions . . . . . 40 × 17 × 20 cm
Sound pressure level LpA . . . . . 69.8 dB(A)
Uncertainty KpA . . . . . . . . . . . . . . . 3 dB
Sound power level LWA . . . . . . .80.8 dB(A)
Uncertainty KWA . . . . . . . . . . . . . . 3 dB
Hand arm vibration . . . . . . . . . .2.3 m/s2
Uncertainty K . . . . . . . . . . . . . 1.5 m/s2
IP class . . . . . . . . . . . . . . . . . . . IP43

Disposal

Do not dispose of electric power tools with domestic refuse.

The electric power tool is shipped in packaging to reduce transport damage.
This packaging is a raw material and as such can either be reused or can be fed back into the raw material cycle. The electric power tool and its accessories are made from various materials such as metals and plastics. Take defective components to a special refuse collection point.
Ask about these at your specialist shop or local council. The product and the user manual may be subject to changes. Technical data may be changed without prior notice.

Batteries

Think of the environment when disposing of batteries. Contact your local authorities to find out where your nearest disposal area is.
Do not dispose of batteries with domestic refuse.
Do not dispose of by burning, risk of explosion.

EC-Declaration of conformity

We, the Batavia B.V., Weth. Wassebaliestraat 6d, NL-7951 SN Staphorst, declare by our own responsibility that the product Cordless drain auger, Model BT- CDA001, Item-No 7063455 is according to the basic requirements, which are defined in the European Directives Electromagnetic Compatibility 2014/30/EU (EMC), 2006/42/EC (Machinery), 2011/65/EU (RoHS) and their amendments. For the evaluation of conformity, the following harmonized standards were consulted:

EN 60745-1:2009+A11:10;
EN 60745-2-21:2009+A1:10;
EK 9-BE-77(V3):2015;
EK 9-BE-88:2014;
EK 9-BE-89:2014;
EK 9-BE-91:2015;
EN 55014-1:2017;
EN 55014-2:2015;
AfPS GS 2019:01 PAK

Staphorst, 6 July 2021

Meino Seinen, QA Representative Batavia B.V., Weth. Wassebaliestraat 6d, 7951 SN Staphorst, Netherlands

The product and the user manual may be subject to changes. Technical data may be changed without prior notice.

WARRANTY

2 YEAR WARRANTY

This product has got a 2 year warranty
Dear Client, if for any reason this product is not working, please ensure you contact our Client Service Centre. Ensure you have your original receipt of purchase. This warranty covers all defects in workmanship or materials in this Batavia product for a two year period from the date of purchase.
The warranty does not cover any malfunction, or defect resulting from misuse, neglect, alteration, or repair.

Other European countries – Customer Services

Monday till Friday from 8 am until 4 pm

 00800 664 774 00

References

• Home - Batavia B.V.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>