BATAVIA 7064217 Fixxpack 12V Cordless Reciprocating Saw Instruction Manual
- October 27, 2023
- BATAVIA
Table of Contents
7064217 Fixxpack 12V Cordless Reciprocating Saw
Instruction Manual
FIXX PACK 12 V
Cordless reciprocating saw
7064217 Fixxpack 12V Cordless Reciprocating Saw
Model: BT-CRS004
Item-No.: 7064217
www.bataviapower.com
OVERVIEW
1. Footplate
2. Saw Blade Holder
3. Saw Blade Clamping Ring
4. Front Handle
5. Motor Vents
6. Trigger Switch
7. Trigger Switch Lock| 8. Hand Grip
9. Battery Charge Indicator
10. Battery (not included)
11. Battery Release Button
12. Sawblade
13. Branch Jaw Clamp
14. Branch Jaw Clamp Release Button
---|---
DEAR CUSTOMERS
Instruction manuals provide valuable hints for using your new device. They
enable you to use all functions, and they help you avoid misunderstandings and
prevent damage. Please take the time to read this manual carefully and keep it
for future reference.
EXPLANATION OF THE SYMBOLS
Warning! To reduce the risk of injury, the user must read the instruction
manual.
Denotes risk of personal injury, loss of life or damage to the tool in case of
non-observance of the instructions in this manual.
Always wear hearing protection. The effects of noise can cause hearing
loss.
Wear a dust mask. When working with wood and other materials, harmful dust may
be generated.
Work with asbestos containing materials is not permitted! Wear safety
glasses. When working with electric power tools, sparks, splinters, chips and
dust particles may be generated and these can cause loss of sight.
**** CE stands for “Conformité Européenne”, which means “In accordance with
EU Regulations”. With the CE marking, the manufacturer confirms that this
Electric tool complies with the applicable European directives.
Do not dispose of electric power tools with domestic refuse.
SAFETY INSTRUCTIONS
The machine must not be damp and must not be operated in a wet environment.
Wear protective gloves and sturdy footwear. Hold power tool by insulated
gripping surfaces, when performing an operation where the cutting accessory
may contact hidden wiring.
Cutting accessory contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.
Do not saw materials containing asbestos!
- Wear protective goggles when working with materials which produce large amounts of chips.
- Wear a protective mask when sawing other fibrous materials.
- Remove adjusting keys and wrenches before turning the tool on.
- Secure your workpiece with clamps.
- Move machine towards the workpiece only when switched on.
- Always hold machine with both hands and ensure that you have a safe footing while working.
- The machine may be operated only with the foot plate mounted. When sawing, the foot plate must always rest on the workpiece.
- Incorrect handling may damage the machine. Therefore always comply with the following instructions.
- Use only sharp saw blades in perfect condition; replace cracked, distorted or blunt saw blades immediately.
- Machine should only be switched on with blade installed.
- Do not attempt to stop the saw blade with lateral pressure after switching off.
- Only use genuine accessories.
INTENDED USE
Battery operated general-purpose reciprocating saw for work on wood, metal and plastics.
UNPACKING THE TOOL
- Carefully unpack and inspect your cordless reciprocating saw. Familiarise yourself with all its features and functions.
- Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged, have such parts replaced before attempting to use this tool.
MOUNTING ACCESSORIES
Fitting a saw blade
The machine is equipped with a quick fit system.
- Turn the clamping ring (3) of the saw blade holder as far to the left as possible and hold it there.
- Place the saw blade in the blade holder.
- Let go of the clamping ring.
- Make sure when changing the saw blade that the blade holder is free of material debris (such as splinters of wood or metal).
- Before use, always check that the saw blade is securely fixed.
Removing the saw blade
- Turn the clamping ring of the saw blade holder as far to the left as possible and hold it there.
- Remove the saw blade from its holder.
- Let go of the clamping ring.
Branch jaw clamp
The branch jaw clamp helps you to guide the equipment when cutting branches.
The machine can be used either with or without the branch jaw clamp.
Inserting/Removing the branch jaw clamp
Inserting:
- Press the branch jaw clamp release button (14)
- Slide the holding bracket over the guides of the footplate into the tool.
- Lock the release button (14)
Removing:
- Press the release button (14) and pull the holding bracket forward and out of the tool
OPERATION
Always follow the safety notes and the relevant safety code.
Make sure that the saw blade does not rest on or touch any objects when the
machine is switched on.
To switch on
- Press the trigger switch lock (7) and the trigger switch (6).
- Press the trigger switch (6) further in to increase the stroke rate.
To switch off
- Release the trigger switch (6) and the trigger switch lock (7).
Sawing tips
- Adjust saw blade and stroke rate to suit the material to be processed. For right radius curves it is best to use a narrow saw blade. Apply coolant or lubricant to deal with the fluttering produced along the cut line when sawing metal.
- Check wood, chip boards, building materials etc, for foreign bodies (nails, screws etc.), before sawing and remove them, if necessary.
- Clamp material well. Do not support the workpiece with hand or foot. Do not touch objects or the floor with the saw running (danger of backlash).
- Put the footplate on the surface of the workpiece, and saw through it with constant contact pressure or feed. If the saw blade seizes switch the machine off immediately. Spread the gap with a suitable tool and pull out the saw blade.
- After finishing work, switch off the machine and only put down after it has come to a complete standstill.
Plunge cutting
- Plunge cutting may only be used on soft materials such as wood, aerated concrete, gypsum plaster boards, etc.
- However, this requires a certain practise and is only possible with short saw blades.
- Place the saw onto the workpiece and switch it on.
- Ensure that the bottom edge of the footplate rests on the workpiece surface.
- Slowly saw into the workpiece at an angle, moving the saw to a vertical position and continue to saw along the cutting line.
- Switch the saw off and lift off the workpiece when the work is complete.
Flush sawing
- Elastic bi-metal saw blades allow you to saw protruding objects (e,g, water pipes, iron bars, etc,) nearby the wall.
- Apply the saw blade directly to the wall and bend slightly so that the footplate rests against the wall.
- Switch the machine on and saw off the workpiece keeping constant lateral pressure against the wall.
MAINTENANCE AND CLEANING
WARNING: Always disconnect from the mains power supply, before carrying
out any maintenance/ cleaning of the charger. Remove the battery before
carrying out any maintenance/ cleaning of the tool. Maintenance There are no
inner parts of the tool which need maintenance.
Cleaning
- Keep safety devices, ventilation openings and the motor housing as free as possible from dirt and dust. Rub the electric power tool with a clean cloth or blow over it with low pressure compressed air.
- We recommend that you clean your electric power tool immediately after each use.
- Clean the electric power tool regularly with a damp cloth and somewhat soft soap. Do not use any cleaning or solvent materials; these can attack the device’s plastic components. Make sure that no water can get inside the electric power tool.
TECHNICAL DATA
Speed . . . . . . . . . . . . . 0 – 2700 min-1
Saw Blade Mount . . . . . . Rotating Sleeve
Saw Stroke …………… 20 mm
Weight . . . . . . . . . . . . . . . . . 1.04 kg
Sound Pressure Level LpA . . . . . 84.3 dB(A)
Uncertainty KpA ………….. 3 dB
Sound Power Level LWA ……. 95.3 dB(A)
Uncertainty KWA ………….. 3 dB
Hand Arm Vibration
Wood…………… 9.15 4 m /s 2
Metal …………… 7. 8 4 5 m /s2
Uncertainty K …………. 1.5 m/s 2
Vibration level
The vibration emission level stated in this instruction manual has been
measured in accordance with a standardised test given in EN62841; it may be
used to compare one tool with another and as a preliminary assessment of
exposure to vibration when using the tool for the applications mentioned.
- using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
- the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level
Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.
DISPOSAL
Do not dispose of electric power tools with domestic refuse.
The electric power tool is shipped in packaging to reduce transport damage.
This packaging is a raw material and as such can either be reused or can be
fed back into the raw material cycle. The electric power tool and its
accessories are made from various materials such as metals and plastics. Take
defective components to a special refuse collection point. Ask about these at
your specialist shop or local council. The product and the user manual may be
subject to changes. Technical data may be changed without prior notice.
Batteries
Think of the environment when disposing of batteries. Contact your local
authorities to find out where your nearest disposal area is.
Do not dispose of batteries with domestic refuse.
Do not dispose of by burning, risk of explosion.
EC-DECLARATION OF CONFORMITY
We, the Batavia B.V., Weth. Wassebaliestraat 6d, NL-7951 SN Staphorst, declare
by our own responsibility that the product Cordless Reciprocating Saw, Model
BT-CRS004, Item-No 7064217 is according to the basic requirements, which are
defined in the European Directives Electromagnetic Compatibility 2014/30/EU
(EMC), 2006/42/EC (Machinery), 2011/65/EU (RoHS) and their amendments. For the
evaluation of conformity, the following harmonized standards were consulted:
EN62841-1:2015
EN62841-2-11:2016 AfPS GS 2019:01
PAK EK9-BE-91(V4):2020
EN55014-1:2017
EN55014-2:2015
Staphorst, 10 March 2022
Meino Seinen, QA Representative
Batavia B.V., Weth. Wassebaliestraat 6d,
7951 SN Staphorst, Netherlands
2 YEAR WARRANTY
This product has got a 2 year warranty
Dear Client, if for any reason this product is not working, please ensure you
contact our Client Service Centre. Ensure you have your original receipt of
purchase. This warranty covers all defects in workmanship or materials in this
Batavia product for a two year period from the date of purchase. The warranty
does not cover any malfunction, or defect resulting from misuse, neglect,
alteration, or repair.
Other European countries – Customer Services
Monday till Friday from 8 am until 4 pm
00800 664 774 00
Model: BT– CRS004
Item-No.: 7064217
www.bataviapower.com
[email protected]
BATAVIA B.V.
Weth. Wassebaliestraat 6d
7951SN Staphorst
Netherlands
7064217/1
Documents / Resources
|
BATAVIA 7064217 Fixxpack 12V Cordless Reciprocating
Saw
[pdf] Instruction Manual
7064217, Fixxpack 12V Cordless Reciprocating Saw, Cordless Reciprocating Saw,
Fixxpack 12V, Reciprocating Saw, Saw
---|---