BATAVIA 7064222 Fixxpack 2Ah Battery Chargers Instruction Manual

: October 27, 2023
: BATAVIA

BATAVIA 7064222 Fixxpack 2Ah Battery Chargers

BATAVIA-7064222-Fixxpack-2Ah-Battery-Chargers-Product-
Image

Overview

BATAVIA-7064222-Fixxpack-2Ah-Battery-Chargers-Fig-01

Battery (not included)
Battery release button
Charger
Green LED
Red LED

Dear customers
Instruction manuals provide valuable hints for using your new device. They enable you to use all functions, and they help you avoid misunderstandings and prevent damage. Please take the time to read this manual carefully and keep it for future reference.

Additional safety instructions for batteries and chargers

Please note the included General Safety Notes and the following safety notes to avoid malfunctions, damage or physical injury:

Batteries

WARNING:
Improper battery use may result in a fire, explosion, or other hazard.

WARNING:
The battery fluid may cause personal injury or damage to property. In case of skin contact, immediately rinse with water. If redness, pain or irritation occurs seek medical attention. In case of eye contact, rinse immediately with clean water and seek medical attention.

Never attempt to open for any reason.
Do not expose the battery to water.
Do not expose the battery to heat.
Do not store in locations where the temperature may exceed 40 °C.
Keep batteries away from children.
Charge only at ambient temperatures between 10 °C and 40 °C.
Charge only using the charger provided with the appliance/tool.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When disposing of batteries, follow the instructions given in the section “Disposal”.
Do not damage/deform the battery pack either by puncture or impact, as this may create a risk of injury and fire.
Do not charge damaged batteries.
Take special care of the battery. Avoid dropping it onto any hard surface and do not subject it to pressure or any other form of mechanical stress. Keep the battery away from extreme heat and cold.
Important Danger! Never short-circuit the battery or expose it to moisture. Do not store it together with any metal parts which could short-circuit the contacts. The battery could overheat, start burning or explode.
Under extreme conditions, battery leakage may occur. When you notice liquid on the batteries, proceed as follows: Carefully wipe the liquid off using a cloth. Avoid skin contact. In case of skin or eye contact, follow the instructions below.

Chargers

Your charger has been designed for a specific voltage. Always check that the mains voltage corresponds to the voltage on the rating plate.

WARNING:

When not in use and before cleaning and servicing, disconnect the battery charger from the power supply.
Never attempt to replace the charger unit with a regular mains plug.
Use your charger only to charge the battery in the appliance/tool with which it was supplied. Other batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
If the supply cord is damaged, it must be replaced by the manufacturer or an authorized Service Centre in order to avoid a hazard.
Do not expose the charger to water. · Do not open the charger. · Do not probe the charger. · The appliance/tool/battery must be placed in a well-ventilated area when charging.
The charger is intended for indoor use only.

Operation

Operation of Lithium-Ion Batteries

Lithium-ion batteries share many characteristics with conventional batteries. The major difference is that Lithium-ion batteries do not have a “memory” and do not require to be completely discharged periodically. It is recommended to charge Lithium-ion batteries after each use so they will be fully charged when needed. Lithium-ion batteries perform best and deliver peak output power at room temperature. When operated in lower temperatures, the battery output will be reduced.

Note: A fully charged battery will loose about 2% of its charge per month during storage.

Before use

The battery must be charged before using it for the first time.

Removing the battery from the machine

BATAVIA-7064222-Fixxpack-2Ah-
Battery-Chargers-Fig-01

Push the battery release button (2) and pull the battery (1) out of the machine.
WARNING: Do not try to remove the battery without pressing the battery release button. The drill or battery could be damaged.

Inserting the battery into the machine

Ensure that the exterior of the battery is clean and dry before connecting to the charger or machine.

Insert the battery (1) into the machine, push the battery further forward until it clicks into place.
Note: Make sure the battery and machine are lined up correctly. If the battery does not slide onto the machine easily, don’t force it. Instead, remove the battery; check the top of the battery and the machine slot are clean and undamaged and that the contacts are not bent.

Charging the Battery

WARNING: Failure to follow the correct procedure when charging batteries will result in permanent damage.

a. Plug the charger plug into an electrical outlet. The green LED indicator (4) on the charger (3) will lighten up.
b. Slide a battery (1) onto the battery charger (3).
c. Once charging commences, the red LED (5) will illuminate.
d. When the battery is fully charged, the green LED (4) will illuminate.

Note: Make sure the battery and battery charger are lined up correctly. If the battery does not slide onto the battery charger easily, don’t force it. Instead, remove the battery; check the top of battery and the battery charger slot are clean and undamaged and that the contacts are not bent.

IMPORTANT: When a low charge level is indicated be aware the tool may stop operating while using the tool. In some instances this may be dangerous. It is recommended to always ensure the battery pack has a good charge level.

Notes about Battery Charging

Let a hot battery cool down before charging it.
The battery should be charged at ambient temperatures between 10 °C and 40 °C (ideally around 20 °C).
After charging, allow 15 minutes for the battery to cool before use.
Ensure that the charger is disconnected from the mains supply after use, and is stored correctly.
Do not leave batteries on charge for extended periods and never store batteries on charge.
The battery charger monitors battery temperature and voltage while charging. Remove the battery once charging has been completed to maximise charge cycles of the battery and not waste power.
Do not store Lithium-Ion battery packs in a discharged state long term. This can damage the Lithium-Ion cells. For long-term storage, store batteries in a high charge state disconnected from the power tool.
The capacity of batteries will reduce over time. After 100 charge cycles, the battery’s operation time and the maximum torque performance of the tool will slightly reduce. This decline will continue until the battery has minimal capacity after 500 charge cycles. This is normal and not a fault with the battery pack.

Technical data

Model	2.4 A 7064222	0.4 A 7064223
Input	220 – 240 V ~

50 – 60 Hz

| 100 – 240 V ~

50 – 60 Hz

Output| 12 V⎓| 14.4 V⎓
Charging Time

2 Ah

Battery

| ****

ca. 40 min

| ****

ca. 280 min

Charging

Current

| 2400 mA| 400 mA
Weight| 0.23 kg| 0.13 kg
Protection

Class

| II| II
---|---|---
IP Code| IPX0| IP20

Disposal

Do not dispose of electric power tools with domestic refuse.
The electric power tool is shipped in packaging to reduce transport damage. This packaging is a raw material and as such can either be reused or can be fed back into the raw material cycle. The electric power tool and its accessories are made from various materials such as metals and plastics. Take defective components to a special refuse collection point. Ask about these at your specialist shop or local council.

Batteries

Think of the environment when disposing of batteries. Contact your local authorities to find out where your nearest disposal area is. Do not dispose of batteries with domestic refuse.
The product and the user manual may be subject to changes. Technical data may be changed without prior notice.

EC-Declaration of conformity

We, the Batavia B.V., Weth. Wassebaliestraat 6d, NL-7951 SN Staphorst, declare by our own responsibility that the product 12V Li-Ion 2.4A Fast Charger, 12 V 0.4 A Charger; Model BT-CLC009, BT-CLC010, is according to the basic requirements, which are defined in the European Directives Electromagnetic Compatibility 2014/30/EU (EMC), 2014/35/EG (LVD), 2011/65/EU (RoHS) and their amendments. For the evaluation of conformity, the following harmonized standards were consulted:

AfPS GS 2019:01 PAK
EN60335-1:2012/A2:2019
EN60335-2-29:2004/A11:2018
EN62233:2008
EN55014-1:2017
EN55014-2:2015
EN61000-3-2:2014
EN IEC 61000-3-2:2019
EN61000-3-3:2013
EN61000-3-3:2013/A1:2019
EN61000-6-3:2007/A1:2011

Staphorst, 03 March 2022
Meino Seinen, QA Representative
Batavia B.V., Weth. Wassebaliestraat 6d, 7951 SN Staphorst, Netherlands

2 YEAR WARRANTY

This product has got a 2 year warranty
Dear Client, if for any reason this product is not working, please ensure you contact our Client Service Centre. Ensure you have your original receipt of purchase. This warranty covers all defects in workmanship or materials in this Batavia product for a two year period from the date of purchase. The warranty does not cover any malfunction, or defect resulting from misuse, neglect, alteration, or repair.