Valcom V-1450 Signature Series In-Wall Speaker INSTALLATION INSTRUCTIONS
- June 12, 2024
- Valcom
Table of Contents
Valcom V-1450 Signature Series In-Wall Speaker
VALCOM SIGNATURE SERIES HIGH FIDELITY SELF-AMPLIFIED IN-WALL SPEAKER
The Valcom Signature Series™ In-Wall Speaker, V-1450, is a high fidelity, self-amplified (6 Watt) speaker and may be used to provide one-way paging and high quality music reproduction from any Valcom Page Control. This speaker has an externally accessible volume control located behind the grille and is screwdriver adjustable. The V-1450 will cover an area up to 600 square feet and should be spaced 20 feet apart. Good quality paging will be heard up to 30 feet in front of the speaker. The V-1450 requires -24VDC, 200mA (4 Valcom power units). The speaker is available in white and supplied with a trim ring and grille.
NOTE: No power amplifier required. Do not connect this speaker directly to a 25/70/100 Volt amplifier as damage to both the amplifier and speaker may occur. (Recommended nominal input level to the V-1450 is -10dBm).
Mounting/Connections
CAUTION: Before cutting hole, identify and locate all plumbing and electrical wiring.
- Using the enclosed cutout template, mark outline of cutout on wall. Make sure speaker is centered between any wall studs. Using the appropriate tool, cut a hole in the wall following the template outline.
- Insert a small screwdriver tip between the grill and speaker to remove grill from the front of the speaker assembly. Assemble speaker, mounting frame and hardware as shown in the diagram. Do not tighten frame completely.
- After assembling mounting frame, make connections to the terminal block. Insert stripped wire into appropriate terminal and tighten with screwdriver. Each connector accepts 18 to 24AWG wire. With the tweeter on top, place mounting bracket into hole in the wall. Push speaker assembly flush to wall and slide up 1/2 inch. Tighten two center screws first, then tighten the remaining screws. Set volume control to 1/2 volume and test. Press grill into slot around speaker assembly.
NOTE: Exercise caution when handling speaker assembly with grill removed.
Recommended Quantity of Speakers per Specific Power Run
(Standard Category 3 Twisted Pair Telephone Wire)
Speakers per Power Run|
Wire Run
|
Length (Feet)
---|---|---
V-1450| 24AWG| 22AWG
8| 125| 200
4| 250| 400
2| 500| 800
Mounting
Dimensions/Weight
- 12.00″H x 8.65″W x 3.20″D (30.48cm H x 21.97cm W x 8.13cm D)
- 3lbs (1.36 kg)
FCC Notice
NOTE: The equipment has been tested and found to comply with the limits for Class A digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
TECHNICAL ASSISTANCE
When trouble is reported, verify there are no broken connections to the unit. Assistance in troubleshooting is available from the factory. When calling, you should have a Volt-Ohm meter and a lineman’s test set available and be calling from the job site. Call 540-563-2000 and ask for Technical Support, or visit our website at http://www.valcom.com.
Valcom equipment is not field repairable. Valcom, Inc. maintains service facilities in Roanoke, VA. Should repairs be necessary, attach a tag to the unit clearly stating your company name, address, phone number, contact person and the nature of the problem. Send the unit to:
Valcom, Inc. Repair and Return Dept. 5614 Hollins Road Roanoke, VA 24019-5056
WARRANTY
Warranty information may be found on our website at www.valcom.com/warranty.
TROUBLESHOOTING CHART
| SYMPTOMS | ACTIONS |
|---|
No audio from speaker
Low volume from speaker
__
__
Loud squeal (Feedback)
| 1. Verify volume control is turned up (Clockwise).
2. Using a lineman’s test set, check for proper audio level on Tip/A and Ring/B leads and if necessary at the source.
1. Verify volume control is turned up.
2. Check voltage at speaker when in use (-18 to -24VDC required).
3. Using a lineman’s test set, check for proper audio level on Tip/A and Ring/B leads. It is possible some low level audio will be heard with only one side of Tip/A and Ring/B connected.
1. Decrease volume of speaker (Counterclockwise).
2. Increase the distance between telephone and speaker.
3. Install confidencer on telephone in severe problem areas.
FREQUENTLY ASKED QUESTIONS
What is the Valcom V-1450 Signature Series In-Wall Speaker?
The Valcom V-1450 is an in-wall speaker designed for audio installations in walls.
What size is the speaker?
The speaker dimensions can vary, but the Valcom V-1450 is typically a 5.25-inch speaker.
Is the speaker designed for residential or commercial use?
The Valcom V-1450 speaker can be used for both residential and commercial audio installations.
What type of installation is this speaker designed for?
This speaker is designed for in-wall installation, offering a discreet audio solution.
Does the speaker come as a single unit or a pair?
The speaker is usually sold individually, so you may need to purchase multiple units for stereo sound.
What is the speaker's impedance?
The speaker's impedance is often 8 ohms.
What is the recommended amplifier power for this speaker?
The recommended amplifier power might vary, but it's often between 5 to 15 watts.
Is this speaker suitable for background music or paging systems?
Yes, the Valcom V-1450 speaker is designed for background music and paging applications.
What is the frequency response range of the speaker?
The frequency response range typically falls around 85Hz to 15kHz.
Is the speaker weather-resistant for outdoor use?
This speaker is usually designed for indoor use and may not be weather- resistant for outdoor installations.
Can this speaker be used as part of a larger audio system?
Yes, you can integrate this speaker into larger audio systems or multi-room setups.
Is this speaker compatible with both low and high-impedance systems?
This speaker is generally designed for low-impedance systems, so check the specifications for compatibility with your system.
Does the speaker require an enclosure or back box?
Some in-wall speakers might require an enclosure or back box for optimal audio performance, but specifications can vary.
What type of audio quality can I expect from this speaker?
Audio quality can vary based on factors like installation and amplifier quality, but this speaker is designed for clear sound reproduction.
Can I paint or customize the appearance of the speaker grille?
Many in-wall speakers, including the Valcom V-1450, offer paintable grilles that you can customize to match your room's decor.
Download the PDF Link:Valcom V-1450 Signature Series In-Wall Speaker INSTALLATION INSTRUCTIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>