childcare 091755-003 Classic Cot Bed Instruction Manual
- June 3, 2024
- childcare
Table of Contents
childcare 091755-003 Classic Cot Bed
SAFETY PRECAUTIONS
Read all instructions before assembly and use of the cot. Keep instructions
for future use.
WARNING
ADULT ASSEMBLY REQUIRED:
DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED TO THE
LOWEST POSITION BEFORE THE CHILD CAN SIT UP.
RECOMMENDED MATTRESS SIZE:
690 MM WIDE X 1300 MM LONG X 100 MM-150 MM THICK. FOLLOW THE MANUFACTURER’S
ASSEMBLY INSTRUCTIONS TO ENSURE THE SAFETY FEATURES OF THE COT ARE NOT
COMPROMISED.
This cot has been manufactured for one child only, with a maximum weight of
18kgs in cot configuration. When the mattress base is assembled in the lower
position, ensure the higher cot base holes are covered tightly with the
filling bolts supplied. This is to prevent finger entrapment, swallowing and
inhalation hazards.
- ENSURE the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.
- ENSURE the cot is completely assembled and check that all parts are securely tightened before placing the child into the cot.
- ENSURE medication, string, elastic, small toys or small items such as money etc are always kept out of the child’s reach from any position in the cot.
- DO NOT over tighten bolts/screws.
- ENSURE that the child is clear of any moving parts when adjusting the cot.
- For warranty purposes, keep your sales receipt to provide proof of purchase.
RECOMMENDED MATTRESS SIZE (SOLD SEPARATELY):
THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS WHICH MEASURES 1300MM
LONG BY 690 MM WIDE AND 100-150 MM IN THICKNESS.
The width and length are specified because it is important that the gaps
between the mattress and the sides and ends of the cot will not exceed 40 mm
when the mattress is pushed to one side or end, and 20mm when the mattress is
centred in the cot. This is to minimize the danger of a child’s limb becoming
caught in the gap. The thickness of the mattress has been specified to ensure
that the depth of the cot is greater than 500 mm with the mattress base in the
lower position and is greater than 300mm with the mattress base in the upper
position, to minimize the risk of a child climbing or falling out of the cot.
CONGRATULATIONS
Congratulations on your purchase of the Childcare Classic Cot. This product
has been designed and developed with safety, comfort and functionality in
mind. Please take the time to read this manual carefully before using this
product and keep it in a safe place for future reference.
Check what you have received…
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service. In Australia,
contact CNP Brands on 1300 667 137, in New Zealand contact Wain house
Distribution on 0800 567 5000.
Supplied loose in box:
ASSEMBLY / OPERATING INSTRUCTIONS
- a. It is advisable that two people assemble the cot in the room in which it is to be used.
- b. As small parts are involved in assembly, children should be kept clear of the assembly area.
- c. Dispose of all packaging material immediately after the cot is assembled.
- d. Identify all parts and components.
- e. Clear an area on the floor for assembly and place a sheet on the floor to ensure the cot is not scratched during assembly.
WARNING
DO NOT OVER TIGHTEN BOLTS. OVER TIGHTENING BOLTS CAN CAUSE PANELS TO CRACK.
-
a. Attach both End Panels to one Side Panel using 4 x 30mm Bolts.
b. Tighten Until Firm. NOTE: Ensure that the bolt recesses are facing out. -
a. Cot should now resemble photo opposite.
-
a. Carefully lay the cot down on the Side Panel.
-
a. Slide the Mattress Base between the End Panels.
WARNING
MATTRESS BASE ‘THIS SIDE UP’ LABEL MUST BE FACING UPWARD WHEN MATTRESS BASE IS
INSTALLED
-
a. Secure the Mattress Base using 4 x 30mm Bolts. b. Do not tighten completely.
-
a. Carefully stand the cot upright.
-
a. Attach the remaining Side Panel between the End Panels using 4 x 30mm Bolts.
-
a. Tighten all bolts until firm.
b. Do not over tighten bolts. Over tightening bolts can cause panels to crack.
-
a. Attach 2 x Legs to each Leg Mounting Panel using 4 x 35mm bolts.
NOTE:
Ensure feet are angled outward when attached to the cot.
- a. Carefully turn the Cot upside down. Attach the legs to each end of the Cot using 5 x 35mm bolts on each panel.
- a. Carefully stand the cot upright. Check all bolts for firmness, but do not overtighten to avoid cracking.
b. The cot is now ready for use in high base mode.
Mattress Base Heights…
Mattress Base in High Position
The base height is set for when your baby is young and cannot sit up unaided.
Mattress Base in Low Position
This is the normal position for an active baby who can sit up unaided. To
adjust Mattress Base Height…
-
a. Carefully lay the cot down on the Side Panel.
b. Remove the 4 x Filler Bolts and Nuts for the lower base position on the End Panels. -
a. Remove 4 x 30mm Mattress Base Bolts.
NOTE:
Loosening the bolts of one end panel will assist in avoiding any scratches or
dents to your Cot whilst sliding the mattress base down to the lower position.
If end panel bolts are loosened during this process, ensure they are re-
tightened after you have moved the mattress base.
- a. Carefully slide the Mattress Base to the lower position and attach with 4 x 30mm Bolts.
- a. Refit 4 x Filler Bolts and Nuts to the upper Mattress Base Mounting holes to prevent possible finger entrapment.
- a. Carefully stand the cot upright.
HOW TO CARE FOR YOUR CHILDCARE COT
Cleaning
This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. To ensure the long-lasting use of your cot, wipe down with a damp cloth and use a mild soap solution if necessary. Do not use abrasive cleaners. Always store product in a clean dry place.
Maintenance
Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or replace if required. To maintain the safety of your cot, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by CNP Brands. If you have any difficulties in assembling the cot, please contact our Service Department. In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wain house Distribution on 0800 567 5000.
Warranty
For all warranty terms and conditions, please visit
cnpbrands.com.au
ABOUT US
About CNP Brands
Currently, CNP Brands boasts one of the most diverse brand portfolios with a
combination of company owned brands and distribution agreements. Our own
brands, including Childcare, have gone from strength to strength in recent
years. Childcare, and our premium brand bebe care, demonstrate our commitment
to quality and continuing investment in product development.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>