childcare 091820 Luton Cot Instruction Manual
- September 27, 2024
- childcare
Table of Contents
091820 Luton Cot
“`html
Specifications:
-
Model: Luton Cot Model # 091820
-
Recommended Mattress Size: 1300 mm long x 690 mm wide x 100-150
mm thick -
Recommended Inner Spring Mattress: 115282-003 Inner Spring
Mattress – White
Product Usage Instructions:
Safety Precautions:
Read all instructions before assembly and use. Keep instructions
for future reference.
Adult assembly required. Keep small parts away from children
until assembly is complete. Adjust the mattress base to the lowest
position before the child can sit up.
Follow manufacturer’s assembly instructions to ensure safety
features are not compromised.
Congratulations:
Congratulations on your purchase of the Luton Cot. Designed for
safety, comfort, and functionality.
Read the manual carefully before use and keep it for future
reference.
Assembly Contents:
Check the contents of the box against the list provided. Contact
Customer Service if anything is missing.
- End Panel x 2
- Filling bolt & nut x 8
- Fixed Side Panel x 1
- Cot Assembly Bolt x 8
- Drop Side Panel x 1
- Allen Key x 1
- Mattress Base x 1
Assembly/Operating Instructions:
-
It is recommended to assemble the cot with two people in the
room of use. -
Keep children away from the assembly area due to small
parts. -
Dispose of packaging material after assembly.
-
Clear an area on the floor for assembly and place a sheet to
protect the cot.
Warning:
Do not over tighten bolts to avoid cracking panels.
To Fit the Drop Side Panel:
-
Attach one side of the drop side panel to one end panel.
-
Guide the pin on the bottom of the drop side panel into the
lower drop side mechanism slot. -
Repeat to attach the other side of the drop side panel to the
second end panel.
To Assemble Mattress Base:
- Lay cot down onto the Drop Side panel.
- Attach one end of the mattress base to one end panel using two
cot assembly bolts.
Warning:
The ‘MATTRESS BASE `THIS SIDE UP’ LABEL’ must be facing upward
when installed.
FAQ:
Q: What should I do if any parts are missing from the box?
A: Contact Customer Service in Australia at 1300 667 137 or in
New Zealand at 0800 567 5000.
“`
Luton Cot Model # 091820
IMPORTANT: RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
SAFETY PRECAUTIONS
Read all the instructions before assembly and use of the cot. Keep
instructions for future use.
WARNING
ADULT ASSEMBLY REQUIRED: DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY,
KEEP OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE. TO PREVENT FALLS,THE
MATTRESS BASE OFTHIS COT SHOULD BE ADJUSTEDTOTHE LOWEST POSITION BEFORE THE
CHILD CAN SIT UP. RECOMMENDED MATTRESS SIZE: 1300 MM LONG X 690 MM WIDE X
100-150 MM THICK. FOLLOW THE MANUFACTURER’S ASSEMBLY INSTRUCTIONS TO ENSURE
THE SAFETY FEATURES OF THE COT ARE NOT COMPROMISED.
Use only accessories as recommended by the supplier. Failure to follow
warnings and instructions could result in serious injury or death. This cot
has been manufactured for one child only, with a maximum weight of 18kgs. The
drop side must be raised when the child is unsupervised. When the mattress
base is assembled in the lower position, ensure the higher cot base holes are
covered tightly with the filling bolts supplied.This is to prevent finger
entrapment,swallowing and inhalation hazards. ENSURE the cot is placed at a
reasonable distance from curtains, blinds, heaters and power points. ENSURE
the cot is completely assembled and check that all parts are securely
tightened before placing the child into the cot. ENSURE medication, string,
elastic, small toys or small items such as money etc are always kept out of
the child’s reach when in the cot. DO NOT over tighten bolts/screws. ENSURE
that the child is clear of any moving parts when adjusting the cot. For
warranty purposes, keep your sales receipt to provide proof of purchase.
RECOMMENDED MATTRESS SIZE (SOLD SEPARATELY): THIS COT HAS BEEN MANUFACTURED
FOR USE WITH A MATTRESS WHICH MEASURES 1300 MM LONG BY 690 MM WIDE AND 100150
MM IN THICKNESS. The width and length are specified because it is important
that the gaps between the mattress and the sides and ends of the cot will not
exceed 40 mm when the mattress is pushed to one side or end, and 20mm when the
mattress is centred in the cot. This is to minimise the risk of a child’s limb
becoming caught in the gap. The thickness of the mattress has been specified
to ensure that the depth of the cot is greater than 500 mm with the mattress
base in the lower position to minimise the risk of a child climbing or falling
out of the cot. SUFFOCATION HAZARD Infants can suffocate;
· In gaps between an extra pad or mattress. · In soft bedding. To reduce the
risk of Sudden Infant Death Syndrome (SIDS), paediatricians recommend healthy
infants be placed on their backs to sleep, unless otherwise advised by your
physician.
2
CONGRATULATIONS
Congratulations on your purchase of the Luton Cot.
This product has been designed and developed with safety, comfort and
functionality in mind. Please take the time to read this manual carefully
before using this product and keep it in a safe place for future reference.
Contents Assembly contents list Assembly / Operating instructions How to care
for your Luton Cot
Due to variations in the style and design of our products, the photographs and
illustrations shown in this instruction manual are generic,therefore product
fabrics,colour and design may vary from images shown. CNP Brands reserves the
right to alter product specifications without notice as a result of our
ongoing policy of product improvement.
3
ASSEMBLY CONTENTS
Check what you have received…
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand contact
Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
End Panel
x 2
Filling bolt & nut (pre-assembled)
x 8
Fixed side panel
x 1
Cot assembly bolt
x 8
Drop side panel
x 1
Allen key
x 1
Mattress base
x 1
Recommended use with 115282-003 Inner Spring Mattress – White.
4
ASSEMBLY / OPERATING INSTRUCTIONS
a.
It is advisable that two people assemble the cot in the room in which it is to
be used.
b.
As small parts are involved in assembly, children should be kept clear of the
assembly area.
c.
Dispose of all packaging material immediately after the cot is assembled.
d.
Identify all parts and components.
e.
Clear an area on the floor for assembly and place a sheet on the floor to
ensure the cot is not scratched during assembly.
WARNING
DO NOT OVER TIGHTEN BOLTS. OVER TIGHTENING BOLTS CAN CAUSE PANELS TO CRACK.
To fit the Drop Side Panel…
1a. With one end panel standing upright,attach one
1
side of the drop side panel by guiding the pin on
its upper corner into the hole located at the top
of the upper drop side mechanism slot.
2a. Guide the pin on the bottom of the drop side panel
2
into the hole located at the top of the lower drop side
mechanism slot.
3a. Repeat to attach the other side of the drop side panel
3
to the second end panel.
5
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Mattress Base…
1a. Lie cot down onto the Drop Side panel.
1
1b. Attach one end of the mattress base to one end panel using two cot
assembly bolts.
WARNING
MATTRESS BASE `THIS SIDE UP’ LABEL MUST BE FACING UPWARD WHEN MATTRESS BASE IS
INSTALLED
2a. Secure with allen key but do not tighten bolts
2
completely.
2b. Repeat for other end of mattress base.
To assemble Fixed Side Panel and Castors…
1a. Slide the fixed side panel between the two end
1
panels and attach using the remaining four cot
assembly bolts.
1b. Insert a castor into housing on each cot leg.
2a. Stand cot upright.
2
2b.
Tighten all eight cot assembly bolts.
The cot is now ready for use.
6
ASSEMBLY / OPERATING INSTRUCTIONS
To operate Drop Side Panel…
To Lower Drop Side Panel
1
1a.
To lower the drop side panel; lift upwards and
press both silver pins simultaneously on the left
and right of the drop side panel.
1b. The panel will then slide down freely.
1c.
For safety, do not force the drop side panel to go
any lower.
To Raise Drop Side Panel
2
2a.
To raise the drop side panel, lift it to the highest
position.
2b. The drop side panel will lock into position.
Mattress Base Heights…
Mattress base in High Position The base height is set for when your baby is
young and cannot sit up unaided.
Mattress base in Low Position. This is the normal position for an active baby who can sit up unaided.
PLEASE NOTE! The cot comes with filling bolts already located in the lower
holes of the end panels. If changing the mattress base from the upper to the
lower position, you must swap over the filling bolts. It is important that the
filling bolts are replaced into the opened holes. Ensure they are secured
tightly with the allen key and check regularly that they do not loosen. For
safe transit, the drop side panel is fitted with rubber cap protectors over
each protruding pin. Please remove the rubber caps prior to assembly, and
dispose of immediately to avoid them becoming a swallowing/choking hazard.
7
ASSEMBLY / OPERATING INSTRUCTIONS
To lower Mattress Base Height…
1a. Lay down the cot on the fixed side panel.
1
1b. Remove the two lower filler bolts and nuts from each of the end panels.
2a. Remove the four mattress base bolts from the
2
end panels.
2b.
Carefully slide the base to match the lower holes
and replace mattress base bolts.
PLEASE NOTE! Re-fit filling bolt and nut to the higher base positions to prevent possible finger entrapment.
8
HOW TO CARE FOR YOUR CHILDCARE COT
Cleaning
This product has been designed and developed with safety, comfort and
functionality in mind. Please take the time to read this manual carefully
before using this product and keep it in a safe place for future reference. To
ensure the long-lasting use of your cot, wipe down with a damp cloth and use a
mild soap solution if necessary. Do not use abrasive cleaners. Always store
product in a clean dry place.
Maintenance
Always check parts regularly for tightness of screws, nuts and other fasteners
tighten or replace if required. To maintain the safety of your cot, seek
prompt repairs for bent, torn, worn or broken parts. Use only those parts and
accessories approved by CNP Brands. If you have any difficulties in assembling
the cot, please contact our Service Department. In Australia, contact CNP
Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800
567 5000.
Warranty
For all warranty terms and conditions, please visit cnpbrands.com.au
9
NOTES 10
NOTES 11
Distributed in Australia by CNP Brands 82 Maribyrnong Street, Footscray, VIC,
3011 Customer Service 1300 667 137
W: www.cnpbrands.com.au E: info@cnpbrands.com.au F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse Distribution 2-6 Argyle St, Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand Customer Service: 0800 567 5000 E: helpline@wainhousedist.co.nz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>