childcare 017000 Stroller Board Instruction Manual
- June 4, 2024
- childcare
Table of Contents
017000 Stroller Board
Instruction Manual
SAFETY PRECAUTIONS
Read all instructions before assembly and use of the stroller board.
Keep instructions for future use.
WARNING
TO AVOID INJURY OR DEATH:
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS STATIONARY.
DO NOT LEAVE THE CHILD UNATTENDED.
ENSURE THAT ALL LOCKING DEVICES ARE ENGAGED BEFORE USE.
- For use with one child at least 2 years of age and a maximum weight of 20kgs.
- This Stroller Board suits most strollers with a rear leg diameter between 3-5cm.
- The child must hold on to the stroller handle at all times while occupying the stroller board.
- The caregiver must have hands on the stroller handle at all times while the child is occupying the stroller board.
- DO NOT make sharp turns or walk at excessive speeds with a child on a stroller board.
- The Stroller board MUST be properly secured to the stroller.
- ENSURE your child is always standing with both feet on the center portion of the stroller board.
- NEVER allow the child to sit on the stroller board.
- DO NOT allow the child to play with or stand on the stroller board without adult supervision.
- The child MUST be supervised and the stroller break engaged when stepping onto and off the stroller board.
- DO NOT allow the child to stand on the stroller board when maneuvering the stroller on steps, over curbs or on rough or irregular surfaces that could cause the child to lose balance.
- Keep the child away from all obstructions on the side of the stroller while on the stroller board.
- Keep hands and feet clear of wheels at all times.
- The child MUST be wearing footwear at all times when standing on the stroller board.
- DO NOT allow the child to stand on the stroller board when not attached to the stroller.
- ENSURE the brake is accessible and functional after the installation of the stroller board.
- Use caution when the stroller board platform is wet or covered with any debris to prevent a child from slipping.
- To avoid injury from tipping, DO NOT allow the child to stand on the stroller board unless the stroller is occupied.
CONGRATULATIONS
Congratulations on your purchase of the Childcare Stroller Board.
This product has been designed and developed with safety, comfort, and
functionality in mind. Please take the time to read this manual carefully
before using this product and keep it in a safe place for future reference.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Stroller Board
Due to variations in the style and design of our products, the photographs and
illustrations shown in this instruction manual are generic, therefore product
fabrics, color, and design may vary from the images shown.
CNP Brands reserves the right to alter product specifications without notice
as a result of our ongoing policy of product improvement.
ASSEMBLY CONTENTS
Check what you have received…
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact
Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
There are no accessories recommended for use with this Childcare Stroller board.
OPERATING INSTRUCTIONS
To assemble Wheels…
1a. Place Stroller Board face down.
1b. Push and hold the wheel release button whilst inserting the Wheel into the
mounting hole.
1c. Release wheel release button to secure.
1d. Repeat for the second wheel.
To
assemble Extension Arms…
1a. Loosen thumbscrews.
1b. Ensuring the mounting post is facing away from the Stroller Board, insert
the Extension Arm into the Stroller Board.
1c. Slightly tighten the thumbscrew until the mounting arm is held in the
Stroller Board slot.
1d. Adjust the horizontal slider on the Extension Arm to the shortest possible
position, as close to the back of the stroller as possible.
1e. Repeat for the second Extension Arm.
To install on the Stroller…
1a. Pull apart the attachment straps and wrap them around the rear leg of the stroller frame at the lowest possible point.
ENSURE: the straps and bracket do not interfere with the operation of the
brake or any other moving parts.
1b. Align the teeth of the two straps and feed the spindle end through the
Attachment Bracket until the strap spindle comes through the back of the
Attachment Bracket.
1c. Secure the Attachment Bracket by screwing the Attachment Strap Thumbscrew
onto the strap spindle until fully tightened and secure.
PLEASE NOTE!
If the Attachment Bracket is still not tight on the Stroller rear leg after
assembly, please undo the Strap Thumbscrew and remove the Attachment Strap.
Take scissors and shorten the straps using the below formula.
Repeat for the second attachment strap. Ensure all straps are cut to the same
length.
Re-fit straps and attachment bracket, ensuring the bracket is tight on the
Rear Stroller Leg and does not move.
Please take care when performing this step to ensure the straps are not cut
too short and are not able to be assembled correctly.
The formula for shortening straps:
Measure the circumference of the Stroller’s Rear Leg. Subtract this number by
12, then divide by 2. (Example: If your stroller leg circumference is 9cm,
12-9=3. Divided by 2=1.5. You will need to cut off 1.5cm from both sides of
the attachment strap.
1d. Repeat steps 1a-1c for the remaining Attachment Strap and Attachment
Bracket.
1e. Flip the Stroller Board and align Extension Arms with the Attachment
Brackets on the rear of the Stroller.
1f. Ensure the mounting posts of the Extension Arms align with the mounting
slot on the assembled
Attachment Brackets.
If necessary, adjust the width of the Extension Armsin or out of the Stroller
Board to ensure the correct alignment.
1g. Attach the Extension Arms to the Attachment Brackets by pushing the
mountings posts down and into the mounting slots until they lock in and are
secure.
1h. Fully tighten the thumbscrews for the Extension Arms until secure.
1i. Ensure the Stroller Board is sitting level and both
Wheels are touching the floor.
If adjustment is required, press and hold both of the Board Adjustment Buttons
and lift or lower to correct position. Release buttons to secure. ENSURE:
all thumbscrews are tight and secure before use.
ENSURE: all components are assembled and secured correctly before use.
The stroller board is now ready for use.
To store the Stroller Board…
1a. Attach the Storage Strap to the handle of your Stroller by wrapping the webbing around the handle and securing it with the buckle.
1b. Raise the rear of the Stroller Board up toward the handle and secure it by
inserting the Storage Strap Clip into the rear of the Stroller board.
1c. Tighten the webbing strap so that the Stroller Board is stored in the most
upright position.
To remove Stroller Board…
1a. To remove Stroller Board from the Attachment
Bracket, slide the locking button on top of the Attachment Bracket down whilst
pulling the Extension Arm mounting posts up and out of the Attachment Bracket.
HOW TO CARE FOR YOUR CHILDCARE STROLLER BOARD
Cleaning
To ensure the long-lasting use of your stroller board, dry it with a soft
absorbent cloth after use in rainy weather. Use a damp cloth with warm water
to clean if required. Do not use abrasive cleaners.
Maintenance
Check the stroller board regularly to ensure that locking devices and
components are secure and working properly. Always check parts regularly for
tightness of screws, nuts, and other fasteners – tighten or replace if
required. To maintain the safety of your stroller board, seek prompt repairs
for bent, torn, worn, or broken parts. Use only those parts and accessories
approved by CNP Brands.
If you have any difficulties in assembling the stroller board, please contact
our Service Department. In Australia, contact CNP Brands on 1300 667 137, in
New Zealand contact Wainhouse Distribution on 0800 567 5000.
Warranty
For all warranty terms and conditions, please visit
cnpbrands.com.au
ABOUT US
About CNP Brands
Currently, CNP Brands boasts one of the most diverse brand portfolios with a
combination of company-owned brands and distribution agreements.
Our own brands, including Childcare, have gone from strength to strength in
recent years. Childcare, and our premium brand Bebe care, demonstrate our
commitment to quality and continuing investment in product development.
Distributed in Australia by CNP Brands
82 Maribyrnong Street, Footscray, VIC, 3011
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: info@cnpbrands.com.au
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000
E:
helpline@wainhousedist.co.nz
http://cnpbrands.com.au/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>