FLEX XS713 Power Tool Sander Instructions

FLEX XS713 Power Tool Sander

Symbols used in this manual

WARNING!
Denotes impending danger. Non-observance of this warning may result in death or extremely severe injuries.

Technical specifications

CAUTION!
Denotes a possibly dangerous situation. Non-observance of this warning may result in slight injury or damage to property.

NOTE
Denotes application tips and important information.

Symbols on the power tool

• Before switching on the power tool, read the operating manual!
• Wear goggles!
• Disposal information for the old appliance (see page 11)!

Safety instructions for random orbit sander

1.  ALWAYS DISCONNECT the sander cord plug from the power circuit before changing the abrasive sheets.
2.  USE A DUST MASK. Wear a protective mask to minimize breathing in the fine dust created while sanding.
3.  NEVER RUN SANDER with the dust container or dust collector assembly removed. Dust could be blown into the eyes.
4.  USE PROPER SAFETY EQUIPMENT. Wear safety goggles to protect your eyes.
5.  SANDING OF LEAD-BASED PAINT IS NOT RECOMMENDED. Lead-based paint should only be removed by a professional.
6.  Use of this tool can generate and disburse dust or other airborne particles, including wood dust, crystalline silica dust, and asbestos dust. Direct particles away from the face and body. Always operate tool in a well-ventilated area and provide for proper dust removal. Use a dust collection system wherever possible. Exposure to dust may cause serious and permanent respiratory or other injuries, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote the absorption of harmful material. Always use properly fitting NIOSH/OSHA-approved respiratory protection appropriate for dust exposure, and wash exposed areas with soap and water.

Replacement parts
When servicing use only identical replacement parts. Exploded drawings and spare-part lists can be found on our homepage: www.flex-tools.com

Operating instructions

Foreword
The FLEX Random Orbit Sander is equipped to accept (Ø 125 mm), “hook & loop” type abrasives. This Random Orbit Sander is suitable for coarse, medium or fine sanding of wood, plaster, metal, and plastics. It is ideal for leveling wallboard joints, finishing cabinets, fitting screens and doors, and for general finishing work in the shop. To start and stop the sander

CAUTION!
Make certain the switch is in the “O” position, and the power source is the same as that specified on the tool’s nameplate.

1. Connect the tool to the power source.
2. The switch button, (A) fig. 1, is labeled “I” and “O”. Depress the “I” end of the switch button to start the motor. Depress the “O” end of the switch button to stop the motor.

Attaching hook & loop abrasive
WARNING!
DISCONNECT THE TOOL FROM THE POWER SOURCE!
To install hook & loop abrasives, align the abrasive with the sander pad and press in place as shown in fig. 2.

Dust extraction
WARNING!
DISCONNECT THE TOOL FROM THE POWER SOURCE!

1. Attach the dust bag to the connection of the sander as shown in fig. 3.
2. Periodically remove dust container from flange and empty collected dust,(see fig. 4).

Tap the container lightly to remove compacted dust. DO NOT WASH THE CONTAINER. Dry compressed air may be used to blow out the container.

CAUTION!
Wear safety glasses while using compressed air. Never run the sander with the dust container or dust collector assembly removed. Dust could be blown into eyes.

It is possible to connect a dust extraction unit using the hose adapter provided.

How to hold the sander
Model XS713 is designed to be held around the main housing, fig. 6.

Sanding procedure

The normal weight of the machine is sufficient for efficient sanding. Do not put additional pressure on the machine. This would only slow down the speed of the pad, reducing the sanding efficiency and putting an additional burden on the motor. In addition, it might cause the sander to jump on the work. Let the sander do the work.

Maintenance

Keep the tool clean!
Periodically blow out all air passages with dry, compressed air. Remove the buildup of grime resulting from working with green or sappy wood. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts.

CAUTION!
Wear safety glasses while using compressed air!

Failure to Sart
Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

Brush inspection and lubrication
At approximately 200 hours of use, take or send your tool to your nearest Authorized FLEX Power Tool Service Agent to be thoroughly cleaned and inspected; worn parts replaced, when necessary; relubricated with fresh lubricant, if required; reassembled with new brushes, and performance tested. Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE THE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to an Authorized FLEX Power Tool Service Agent for immediate service.

Service and repairs
All quality tools eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by an Authorized FLEX Power Tool Service Agent. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.).

Disposal information

• Render redundant power tools unusable by removing the power cord.
• EU countries only Do not throw electric power tools into household waste! In accordance with the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and transposition into national law used electric power tools must be collected separately and recycled in an environmentally friendly manner.
  NOTE
  Please ask your dealer about disposal options!

Declaration of Conformity

We declare under our sole responsibility that the product described under “Technical specifications” conforms to the following standards or normative documents:EN 60745 in accordance with the regulations of the directives 2014/30/EU, 2006/42/EC, 2011/65/EU. Responsible for technical documents: FLEX- Elektrowerkzeuge GmbH, R & D Bahnhofstrasse 15, D-71711 Steinheim/Murr02.07.2018 FLEX-Elektrowerkzeuge GmbH Bahnhofstrasse 15, D-71711 Steinheim/Murr

Declaration of Conformity

We as the manufacturer: of FLEX Elektrowerkzeuge GmbH,
Business address: Bahnhofstr. 15, 71711 Steinheim, Germany
declare under our sole responsibility, that the product(s) described under „Technical specifications“ fulfills all the relevant provisions of The Supply of Machinery (Safety) Regulations S.I. 2008/1597 and also fulfills all the relevant provisions of the following UK Regulations: Electromagnetic Compatibility Regulations S.I. 2016/1091, The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment RegulationsS.I. 2012/3032 and are manufactured in accordance with the following designated Standards: BS EN 62841-1:2015, BS EN 62841-2-4:2014, BS EN 55014-1:2017, BS EN 55014-2:2015, BS EN 61000-3-2:2014, BS EN 61000-3-3:2013 Place of declaration: Steinheim, Germany.Responsible person: Peter Lameli, Technical Director – FLEX-Elektrowerk-zeuge GmbH Contact details for Great Britain: FLEX Power Tools Limited, Unit 8 Anglo Office Park, Lincoln Road, HP 12, 3RH Buckinghamshire, United Kingdom

Exemption from liability
The manufacturer and his representative are not liable for any damage and lost profit due to interruption in business caused by the product or by an unusable product. The manufacturer and his representative are not liable for any damage which was caused by improper use of the power tool or by use of the power tool with products from other manufacturers.

References

• Power tools for professional craftsmen | FLEX - FLEX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>