Turbosound NuQ62-FY NuQ Brackets User Guide
- June 4, 2024
- Turbosound
Table of Contents
Turbosound NuQ62-FY NuQ Brackets
Thank you for choosing a TURBOSOUND loudspeaker product for your application.
If you would like further information about this or any other product, please
visit our website at turbosound.com.
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2022 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.
Unpacking
After unpacking the unit, please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future return shipment.
Mounting and Fixing
NuQ full-range series cabinets are designed with multiple internal rigging points to suit many possible mounting methods in permanent installations. NuQ series two-way cabinets are equipped with pole mount sockets for portable use on 35 mm speaker stands or poles. Bass cabinets are equipped with pole mount receptacles that allow two-way cabinets to be mounted at the correct height.
TURBOSOUND wall and ceiling brackets are optionally available for installing NuQ series cabinets. They are also compatible with industry standard wall and ceiling brackets. Some examples are shown below
Model| Wall Mount| Flying Yoke| Swivel Bracket| Swivel
Extenders| Eyebolts
---|---|---|---|---|---
NUQ62| –| NUQ62-FY| NuQ62-SB| –| M8
NuQ82| WB-20B, PB-55| NuQ82-FY| NuQ82-SB| NuQ82-EB| M10
NuQ102| WB-20B, PB-55| NuQ102-FY| NuQ102-SB| NuQ102-EB| M10
NuQ122| WB-55B, PB-55| NuQ122-FY| –| –| M10
NuQ152| WB-55B, PB-55| NuQ152-FY| –| –| M10
Bracket Assembly
NuQ62-FY
- Mount the bracket to the ceiling or wall in desired location.
- Lift the speaker into the bracket and attach the included screws on either side. Position the speaker angle before tightening.
NuQ62-SB
- • Mount the bracket to the ceiling or wall in desired location.
• Attach the smaller bracket joints to the top and bottom of the speaker with the included M8x12 bolts.
• Lift the speaker into the bracket and attach the M8x16 screws to the bracket and bracket joints. Position the speaker angle before tightening.
NuQ82/102/122/152-FY
- Attach one of the side plates to the bracket by sliding the threaded screw of the plate through the hole in the bracket arm.
- Place one of the larger 13 mm flat washers over the threaded screw, followed by a 13 mm spring washer, followed by another 13 mm flat washer.
- Lightly screw one of the knobs onto the threaded screw to secure the plate to the bracket.
- Repeat the above steps to attach the other side plate to the bracket.
- Mount the bracket assembly to the ceiling or wall in desired location.
- Place one of the smaller 10 mm spring washers onto one of the M10 screws, followed by a 10 mm flat washer. Repeat for the other 3 screws.
- Lift the speaker into the bracket assembly and attach the screws through the side plates and into the threaded inserts in the side of the speaker. Position the speaker angle before tightening the side knobs.
NuQ82/102-SB
- Mount the bracket to the ceiling or wall in desired location.
- Insert the swivel holder into the speaker pole socket on the bottom ofthe speaker.
- One arm of the bracket has 2 holes side-by-side at the end, while the other arm has one hole. Lift the speaker into the bracket so that the bottom of the speaker faces the bracket arm with 2 holes at the end.
- Attach the larger M5 screws through the 2 holes and into the swivel holder.
- Lightly screw the plastic handle screw through the other bracket arm and into the top of the speaker. Position the speaker angle before tightening the handle screw.
- Insert the M4 screws through the remaining holes in the bracket arm and into the speaker to solidify the speaker angle.
NuQ82/102-EB
- Mount the SB bracket to the ceiling or wall in desired location.
- Insert the swivel holders into the speaker pole socket on the bottom of each speaker.
- While installing the first speaker into the bracket as described in the SB instructions, include the extension arms on the outer side of the bracket before the screws and knob are installed. Make sure the extension with the 2 diagonal slots goes on the side where the bottom of the speaker is attached.
- After the first speaker is installed, lift the second speaker into the extension arms and repeat the installation steps. The angle of the extension arms and of the second speaker can be adjusted before tightening the respective screws.
Suspending with Eyebolts
NuQ cabinets can be suspended using optional eyebolts coupled to the internal
rigging points provided on the top, bottom and sides and back. The simplest
method is to use the two rigging points on the top and a single pull-back
rigging point in the centre of the rear panel.
Remove the appropriate countersunk screws and replace them with shoulder
eyebolts, which must have a thread length of at least 18 mm. Use the rear
rigging point to angle the cabinet for optimum room coverage. Cabinets may be
hung upside downif required.
IMPORTANT NOTE: The mounting of a permanently installed sound system may be
dangerous unless undertaken by qualified personnel with the required
experience and certification to perform the necessary tasks. Walls, floors or
ceilings must be capable of safely and securely supporting the actual load.
The mounting accessory used must be safely and securely fixed both to the
loudspeaker and to the wall, floor or ceiling.
When mounting rigging components on walls, floors or ceilings, ensure that all
fixings and fasteners used are of an appropriate size and load rating. Wall
and ceiling claddings, and the construction and composition of walls and
ceilings, all need to be taken into account when determining whether a
particular fixing arrangement can be safely employed for a particular load.
Cavity plugs or other specialist fixings, if required, must be of an
appropriate type, and must be fitted and used in accordance with the maker’s
instructions.
The operation of your speaker cabinet as part of a flown system, if installed
incorrectly and improperly, can potentially expose persons to serious health
risks and even death. In addition, please ensure that electrical, mechanical
and acoustic considerations are discussed with qualified and certified (by
local state or national authorities) personnel prior to any installation or
flying.
Make sure that speaker cabinets are set up and flown by qualified and
certified personnel only, using dedicated equipment and original parts and
components delivered with the unit. If any parts or components are missing
please contact your dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in
your country. Music Tribe, including the Music Tribe companies listed on the
enclosed “Service Information Sheet”, assumes no liability for any damage or
personal injury resulting from improper use, installation or operation of the
product. Regular checks must be conducted by qualified personnel to ensure
that the system remains in a secure and stable condition. Make sure that,
where the speaker is flown, the area underneath the speaker is free of human
traffic. Do not fly the speaker in areas that can be entered or used by
members of the public.
Speakers create a magnetic field, even if not in operation. Therefore, please
keep all materials that can be affected by such fields (discs, computers,
monitors, etc) at a safe distance. A safe distance is usually between 1 and 2
metres.
Hereby, Music Tribe declares that this product is in compliance with Directive
2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation
519/2012 REACH SVHC and Directive 1907/2006/EC, and this passive product is
not
applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>