Turbosound TCS62 TCS Passive Series Arrayable Full Range Loudspeakers and Subwoofers User Guide

TCS Passive Series
TCS62 (WH), TCS122/64 (WH), TCS122/96 (WH), TCS122/94 (WH),
TCS152/64 (WH), TCS152/96 (WH), TCS152/94 (WH), TCS115B (WH),
TCS218B (WH), TCS110B (WH), TCS212B (WH)
Arrayable Full Range Loudspeakers and Subwoofers
User Guide

Important Safety

Instructions

CAUTION
RISK OF ELECTRIC SHOCK!
DO NOT OPEN!
Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute a risk of electric shock. Use only high- quality professional speaker cables with ¼” TS or twist-locking plugs pre- installed. All other installations or modifications should be performed only by qualified personnel.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
** This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user-serviceable parts inside. Refer servicing to qualified personnel.
Caution
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Caution**
These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
18. Do not install it in a confined space, such as a bookcase or similar unit.
19. Do not place naked flame sources, such as lighted candles, on the apparatus.
20. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed of at a battery collection point.
21. This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Thank you for choosing a Turbosound loudspeaker product for your application. If you would like further information about this or any other Turbosound product, please visit our website at turbosound.com.
Unpacking the Loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim.
Please retain all packaging in case of future re-shipment.
System Requirements – Passive and Bi-amped Loudspeakers
TCS62 2-way loudspeaker operates as a passive system and requires only one amplifier channel. The input signal is divided between the low-frequency and high-frequency drivers internally with a passive crossover.
TCS122 and TCS152 are switchable passive / bi-amp 2-way loudspeakers. Passive operation (full range or with a subwoofer) requires 1 amplifier channel and 1 controller channel. The input signal is divided between the low-frequency and high-frequency drivers internally with a passive crossover. Bi-amp operation (full range or with a subwoofer) requires 2 amplifier channels and 2 controller channels, one for low frequencies and one for high frequencies. The input signal is divided between the low-frequency and high-frequency driver in the controller and the individual amplified signals are fed to the speaker input.
TCS218B subwoofer has a switchable input to allow operation in parallel or discrete modes. Parallel operation connects both drivers in parallel internally. Operation requires 1 amplifier channel and 1 controller channel. Discrete operation connects each driver separately to the two channels of the input. Operation requires 1 amplifier channel and a minimum of 1 controller channel.
TCS115B, TCS212B, and TCS110B subwoofers operate as passive systems and require only one amplifier channel.
Correct controller settings for all models, horn variants, and operation with subwoofers can be downloaded from the website, and are also available as presents for the LMS series controllers.
To avoid wasting amplifier power, you should use heavy-duty speaker cable, with a minimum wire size of 1.5 mm2 (16 AWG), and preferably 2.5 mm2 (14 AWG) for longer runs. Use larger wire sizes for the TCS212B and TCS218B and speakers wired in parallel. For extreme cable lengths, be aware of cable impedance and resistive losses. Always observe the correct polarity.

TCS Passive Series

Amplifier Considerations
The TCS series loudspeakers are optimized for use with the Turbosound T series amplifiers with the LMS series controllers. A full range of DSP settings to suit any configuration are provided for download on the Turbosound website. The use of third-party amplification and processing is only advised using the matrix of manual settings as well as the limiter calculator provided on the Turbosound website. The TCS series loudspeaker enclosures should be driven by high-quality power amplifiers designed for true professional use. Power amplifiers should be capable of delivering long-term broadband power equal to half the loudspeaker’s peak power rating at its stated nominal impedance. The use of underpowered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers, and equalization points must be set in accordance with the settings provided on the Turbosound website. This will ensure optimum sound quality and long-term reliability as well as protection from damage. Neutrik speakON* NL4 locking input connector(s) and 4-way barrier strip(s) are provided, allowing options for input and link, passive, bi-amp, parallel, and discrete operation.

Recommended Minimum Amplifier Power

Model| TCS62| TCS122| TCS152| TCS110B| TCS212B| TCS115B| TCS218B
---|---|---|---|---|---|---|---
Mode| Passive| Passive| Bi-amp LF| Bi-amp LF| Passive| Bi-amp LF| Bi-amp HF| Passive| Passive| Passive| Passive
Impedance| 8 Ohms| 8 Ohms| 8 Ohms| 6 Ohms| 8 Ohms| 8 Ohms| 6 Ohms| 8 Ohms| 4 Ohms| 8 Ohms| 4 Ohms
Minimum
Amplifier
Power| Continuous
RMS| 175 W| 600 W| 600 W| 75 W| 600 W| 600 W| 75 W| 300 W| 800 W| 500 W| 1600 W
Peak| 700 W| 2400 W| 2400 W| 750 W| 2400 W| 2400 W| 750 W| 1200 W| 3200 W| 2000 W| 6400 W

Connections

TCS62

Loudspeakers and Subwoofers - Figure 1](https://manuals.plus/wp- content/uploads/2022/10/Turbosound-TCS62-TCS-Passive-Series-Arrayable-Full- Range-Loudspeakers-and-Subwoofers-Figure-1.jpg)| *speakON NL4**|

TCS122, TCS152

Mode| | |
---|---|---|---
Passive| | speakON NL4
|
Bi-Amp| | speakON NL4|

TCS110B, TCS212B, TCS115B

**|

TCS218B

Loudspeakers and Subwoofers - Figure 13](https://manuals.plus/wp- content/uploads/2022/10/Turbosound-TCS62-TCS-Passive-Series-Arrayable-Full- Range-Loudspeakers-and-Subwoofers-Figure-13.jpg)| speakON NL4|
Discrete| | speakON NL4|

Mounting and Fixing

The table below summarises the rigging parts or kits required for various applications, and some examples of the possible rigging options are illustrated.
TCS series cabinets are designed with multiple internal rigging points to suit many possible mounting methods in permanent installations. All cabinets can be simply suspended using optional M8 or M10 shoulder eyebolts coupled to the internal rigging points provided. Remove the appropriate countersunk screws and replace them with eyebolts, which must have a thread length of at least 18mm. Use the rear rigging point to angle the cabinet for optimum room coverage. Cabinets may be hung upside down if required.  Turbosound WB-20, WB-55, and CB-55 wall and ceiling brackets are optionally available for TCS series cabinets, and these are also compatible with OmniMount* wall and ceiling brackets which use 60 mm x 60 mm hole spacing.

Model| Wall| Ceiling| Downfall| Array Kit| Eyebolts
---|---|---|---|---|---
TCS62| WB-20
TCS62-SB| CB-55
TCS62-SB| TCS62-SB| | M8 Thread
TCS122| WB-55| CB-55| | TCS122-FP
TCS-FK1
TCS-FK2| EB-10-40
TCS152| WB-55| CB-55| | TCS152-FP
TCS-FK1
TCS-FK2| EB-10-40
TCS115B| | | | TCS115-FP
TCS-FK3| EB-10-40
TCS Subwoofers| | | | | EB-10-40

Some typical examples of the possible rigging options are shown here:

TCS Series Flying Components

Wall and Ceiling Brackets
To install a loudspeaker using Turbosound wall and ceiling brackets, first, separate the brackets into their wall/ceiling plate and speaker plate component parts. Remove the countersunk bolts on the rear panel of the cabinet. Attach the speaker plate to the cabinet with the bolts supplied. Fix the wall/ceiling plate in the venue using appropriate fixings (not supplied). Lift the loudspeaker onto the wall plate and re-assemble the bracket parts, adjust the vertical angle and tighten all bolts.
Downfall Applications
The TCS62 can be mounted underneath a TCS122 or TCS152 cabinet to provide downfill coverage using the TCS62-SB swivel bracket. First, disassemble the swivel bracket into its component parts. Remove the countersunk bolts from the bottom panel of the TCS152 cabinet and fit the section with the elongated holes using the fixings supplied. Remove the countersunk bolts on the top panel and fit the swivel bracket using the supplied fixings. Re-assemble the swivel bracket, angle as appropriate, and tighten all fixings. To install the TCS62 in a ceiling-mount application, separate the component parts as above, and fix the top section to the ceiling with appropriate fixings (not supplied). Fit the other half to the TCS62 cabinet, re-assemble the bracket, angle as appropriate, and tighten all fixings.
Loudspeaker Arrays and Clusters
An array of two or more cabinets requires the use of kits of fly plates and inter-cabinet couplers, which are fixed to the cabinet sides through the M10 rigging points and assembled together in a ‘daisy chain’ fashion to build up the required array. For all loudspeaker arrays consisting of two or more cabinets: The number of inter cabinet coupler kits required = the number of boxes – 1, The number of fly plate kits required = the number of boxes.
Illustrated here are the components parts available for TCS cabinets:

Contents:
Contents:
Contents:

Suspending with Eyebolts

TCS cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided on the top, bottom and sides, and back. The simplest method is to use the two rigging points on the top and a single pull-back rigging point in the center of the rear panel.
Remove the appropriate countersunk screws and replace them with shoulder eyebolts, which must have a thread length of at least 18 mm. Use the rear rigging point to angle the cabinet for optimum room coverage. Cabinets may be hung upside down if required.
IMPORTANT NOTE FOR ALL INSTALLATION METHODS: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualified personnel with the required experience and certification to perform the necessary tasks. Walls, floors, or ceilings must be capable of safely and securely supporting the actual load. The mounting accessory used must be safely and securely fixed both to the loudspeaker and to the wall, floor, or ceiling.
When mounting rigging components on walls, floors, or ceilings, ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a particular fixing arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, and must be fitted and used in accordance with the maker’s instructions. The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly, can potentially expose persons to serious health risks and even death. In addition, please ensure that electrical, mechanical, and acoustic considerations are discussed with qualified and certified (by local state or national authorities) personnel prior to any installation or flying.
Make sure that speaker cabinets are set up and flown by qualified and certified personnel only, using dedicated equipment and original parts and components delivered with the unit. If any parts or components are missing please contact your Dealer before attempting to set up the system. Be sure to observe the local, state, and other safety regulations applicable in your country. Music Tribe, including the Music Tribe companies listed on the enclosed “Service Information Sheet”, assumes no liability for any damage or personal injury resulting from improper use, installation or operation of the product.
Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of human traffic. Do not fly the speaker in areas that can be entered or used by members of the public. Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials that can be affected by such fields (discs, computers, monitors, etc) at a safe distance. A safe distance is usually between 1 and 2 meters.

Rotating the HF horn pattern

The high-frequency horn in all TCS122 and TCS152 models can be rotated through 90° in order to swap the horizontal and vertical dispersion patterns, particularly useful when assembling clusters or for example to retain the original dispersion when the cabinet is installed in a horizontal orientation.

1. Place the cabinet on its back on a suitable work surface.

2. Remove the 10 positive screws that hold the grille in place and set the grille aside (fig 1).

3. Remove and disconnect the bass driver (fig 2) to access the compression driver retaining brace, making a note of the bass driver polarity for later reconnection.

4. Reach in through the bass driver cavity and loosen the two wing nuts securing the compression driver retaining brace (fig 3).

5. Remove the horn fixing screws that secure the horn to the enclosure and lift out the horn and compression driver assembly (fig 4).
   (If required for servicing or replacement, disconnect the cables from the compression driver, making a note of the polarity for later reconnection.)

6. Rotate the horn to achieve the desired coverage pattern (fig 5).

7. Re-assemble the cabinet and drivers by reversing steps 1-5.

8. If the compression driver cables have been disconnected, reconnect the cables while observing the correct polarity (white cable to the +ve terminal, black cable to the –ve terminal).

9. Place the horn and compression driver back into the cabinet, making sure that the driver cables pass underneath the compression driver retainer and that the compression driver fits squarely back into the retaining brace.

10. Tighten the wing nuts back onto the compression driver retaining brace (fig 3).

11. Replace the horn fixing screws and tighten them to secure the horn back into the enclosure (fig 4).

12. Reconnect the bass driver cables, observing the correct polarity (red cable to the +ve terminal, blue cable to the –ve terminal).

13. Check all components and confirm the horn orientation is correct (fig 6).

14. Replace the grille (fig 1) and phase-check the cabinet before use.

Technical Specifications

| TCS62 (WH)| TCS122/64 (WH)| TCS122/94 (WH)
---|---|---|---
System| | |
Frequency response| 60 Hz – 20 kHz ±3 dB
50 Hz – 20 kHz -10 dB| 50 Hz – 18 kHz ±3 dB
45 Hz – 20 kHz -10 dB| 50 Hz – 18 kHz ±3 dB
45 Hz – 20 kHz -10 dB
Nominal dispersion| 100° H x 60° V @ -6dB points, rotatable| 60° H x 40° V @ -6 dB points, rotatable| 90° H x 40° V @ -6 dB points, rotatable
Directivity factor (Q)| 12.8| 18.3| 12.9
Directivity index (DI)| 11.1| 12.6| 11.1
Power handling (IEC)| | |
Passive| 175 W continuous, 700 W peak| 600 W continuous, 2400 W peak| 600 W continuous, 2400 W peak
Bi-amp| –| LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak| LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak
Sensitivity| 90 dB (1 W @ 1 m)| 96 dB (1 W @ 1 m)| 96 dB (1 W @ 1 m)
Maximum SPL| | |
Passive| 112.5 dB continuous, 118.5 dB peak| 124 dB continuous, 130 dB peak| 124 dB Continuous, 130 dB Peak
Bi-amp| –| LF: 124 dB continuous, 130 dB peak HF: 128 dB continuous, 134 dB peak| LF: 124 dB Continuous, 130 dB Peak HF: 128 dB Continuous, 134 dB Peak
Impedance| | |
Passive| 8 Ω| 8 Ω| 8 Ω
Bi-amp| –| LF: 8 Ω
HF: 6 Ω| LF: 8 Ω
HF: 6 Ω
Crossover type| Passive| Passive / Bi-amp, switchable| Passive / Bi-amp, switchable
Components| 1 x 6″ (162 mm) LF driver
1 x 1″ (25 mm)
HF compression driver| 1 x 12″ (312 mm) LF driver
1 x 1.4″ (36 mm)
HF compression driver| 1 x 12″ (312 mm) LF driver
1 x 1.4″ (36 mm)
HF compression driver
Enclosure| | |
---|---|---|---
Connectors| 1 x Neutrik speakON* NL4,

1 x barrier strip terminals

| 1 x Neutrik speakON* NL4,

1 x barrier strip terminals

| 1 x Neutrik speakON* NL4,

1 x barrier strip terminals

Wiring| | |
Passive| Pins 1+ / 1- input, pins 2+ / 2- link| Pins 1+ / 1- input, pins 2+ / 2- link| Pins 1+ / 1- input, pins 2+ / 2- link
Bi-amp| –| Pins 1+ / 1- LF, pins 2+ / 2- HF| Pins 1+ / 1- LF, pins 2+ / 2- HF
Dimensions (HWD)| 224 x 402 x 198 mm
(8.8 x 15.8 x 7.8″)| 834 x 399 x 425 mm
(32.8 x 15.7 x 16.7″)| 834 x 399 x 425 mm
(32.8 x 15.7 x 16.7″)
Net weight| 6.9 kg (15.2 lbs)| 26.5 kg (58.4 lbs)| 26.5 kg (58.4 lbs)
Construction| 12 mm (½”) birch plywood| 15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood
Finish| Semi-matte black paint (white
optional)| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M8 X 8, M6 X 2 Points| M10 x 9, M8 X 8 Points| M10 x 9, M8 X 8 Points
Accessories| | |
---|---|---|---
| TCS62-SB (WH) Swivel Bracket for TCS62| TCS122-FP (WH) fly plate kit for TCS122 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152
TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152| TCS122-FP (WH) fly plate kit for TCS122 TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152 TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152
TCS122/96 (WH)| TCS152/64 (WH)| TCS152/94 (WH)|

TCS152/96 (WH)

---|---|---|---
| | |
50 Hz – 18 kHz ±3 dB
45 Hz – 20 kHz -10 dB| 41 Hz – 18 kHz ±3 dB
35 Hz – 20 kHz -10 dB| 41 Hz – 18 kHz ±3 dB
35 Hz – 20 kHz -10 dB| 41 Hz – 18 kHz ±3 dB
35 Hz – 20 kHz -10 dB
90° H x 60° V @ -6 dB points, rotatable| 60° H x 40° V @ -6 dB points, rotatable| 90° H x 40° V @ -6 dB points, rotatable| 90° H x 60° V @ -6 dB points,
rotatable
8.7| 18.3| 12.9| 8.7
9.4| 12.6| 11.1| 9.4
| | |
600 W continuous, 2400 W peak| 600 W continuous, 2400 W peak| 600 W continuous, 2400 W peak| 600 W continuous, 2400 W peak
LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak| LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak| LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak| LF: 600 W Continuous, 2400 W peak HF: 75 W continuous, 300 W peak
96 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)
| | |
124 dB Continuous, 130 dB Peak| 125 dB Continuous, 131 dB Peak| 125 dB Continuous, 131 dB Peak| 125 dB Continuous, 131 dB Peak
LF: 124 dB Continuous, 130 dB Peak HF: 128 dB Continuous, 134 dB Peak| LF: 125 dB Continuous, 131 dB Peak HF: 128 dB Continuous, 134 dB Peak| LF: 125 dB Continuous, 131 dB Peak HF: 128 dB Continuous, 134 dB Peak| LF: 125 dB Continuous, 131 dB Peak HF: 128 dB Continuous, 134 dB Peak
| | |
8 Ω| 8 Ω| 8 Ω| 8 Ω
LF: 8 Ω
HF: 6 Ω| LF: 8 Ω
HF: 6 Ω| LF: 8 Ω
HF: 6 Ω| LF: 8 Ω
HF: 6 Ω
Passive / Bi-amp, switchable| Passive / Bi-amp, switchable| Passive / Bi-amp, switchable| Passive / Bi-amp, switchable
1 x 12″ (312 mm) LF driver
1 x 1.4″ (36 mm) HF compression driver| 1 x 15″ (394 mm) LF driver
1 x 1.4″ (36 mm)
HF compression driver| 1 x 15″ (394 mm) LF driver
1 x 1.4″ (36 mm)
HF compression driver| 1 x 15″ (394 mm) LF driver
1 x 1.4″ (36 mm)
HF compression driver
1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals
---|---|---|---
| | |
Pins 1+ / 1- input, pins 2+ / 2- link| Pins 1+ / 1- input, pins 2+ / 2- link| Pins 1+ / 1- input, pins 2+ / 2- link| Pins 1+ / 1- input, pins 2+ / 2- link
Pins 1+ / 1- LF, pins 2+ / 2- HF| Pins 1+ / 1- LF, pins 2+ / 2- HF| Pins 1+ / 1- LF, pins 2+ / 2- HF| Pins 1+ / 1- LF, pins 2+ / 2- HF
834 x 399 x 425 mm
(32.8 x 15.7 x 16.7″)| 834 x 473 x 451 mm
(32.8 x 18.6 x 17.8″)| 834 x 473 x 451 mm
(32.8 x 18.6 x 17.8″)| 834 x 473 x 451 mm
(32.8 x 18.6 x 17.8″)
26.5 kg (58.4 lbs)| 28.9 kg (63.7 lbs)| 28.9 kg (63.7 lbs)| 28.9 kg (63.7 lbs)
15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood
Semi-matte black paint (white optional)| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)
Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
M10 x 9, M8 X 8 Points| M10 x 9, M8 X 8 Points| M10 x 9, M8 X 8 Points| M10 x 9, M8 X 8 Points
TCS122-FP (WH) fly plate kit for TCS122
TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152
TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152| TCS152-FP (WH) fly plate kit for TCS152
TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152
TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152| TCS152-FP (WH) fly plate kit for TCS152
TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152
TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152| TCS152-FP (WH) fly plate kit for TCS152
TCS-FK1 (WH) inter-cabinet coupler kit for TCS122 or TCS152
TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or
TCS152
---|---|---|---
| TCS110B (WH)| TCS212B (WH)| TCS115B (WH)|

TCS218B (WH)

---|---|---|---|---
System| 50 Hz – 150 Hz ±3 dB
40 Hz – 200 Hz -10 dB| 38 Hz – 200 Hz ±3 dB
32 Hz – 200 Hz -10 dB| 45 Hz – 150 Hz ±3 dB
40 Hz – 200 Hz -10 dB| 33 Hz – 200 Hz ±3 dB
27 Hz – 200 Hz -10 dB
Frequency response
Nominal dispersion| Half space| Half space| Half space| Half space
Power handling (IEC)| 300 W continuous, 1200 W peak| 800 W continuous, 3200 W peak| 500 W continuous, 2000 W peak| 1600 W continuous, 6400 W peak
Sensitivity| 94 dB (1 W @ 1 m)| 100 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)| 99 dB (1 W @ 1 m)
Maximum SPL| 119 dB continuous, 125 dB peak| 129 dB continuous, 135 dB peak| 124 dB continuous, 130 dB peak| 131 dB continuous, 137 dB peak
Impedance| 8 Ω| 4 Ω| 8 Ω| Parallel: 4 Ω
Discrete: 8 Ω x 2
Components| 1 x 10″ (262 mm) LF driver| 2 x 12″ (316 mm) LF driver| 1 x 15″ (387 mm) LF driver| 2 x 18″ (460 mm) LF driver
Enclosure| | | |
Connectors| 1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals| 1 x Neutrik speakON NL4,
1 x barrier strip terminals
Wiring| | | |
Parallel / No switch| Pins 1+ / 1- input,
pins 2+ / 2- link| Pins 1+ / 1- input,
pins 2+ / 2- link| Pins 1+ / 1- input,
pins 2+ / 2- link| Pins 1+ / 1- input,
pins 2+ / 2- link
Discrete| –| –| –| Pins 1+ / 1- input 1,
pins 2+ / 2- input 2
Dimensions (HWD)| 330 x 585 x330 mm
(13.0 x 23.0 x 13.0″)| 420 x 1000 x470 mm
(16.5 x 39.4 x 18.5″)| 834 x 469 x 452 mm
(32.9 x 18.5 x17.8″)| 1130 x @710 x 730 mm
(44.5 x 28.0 x 28.8″)
Net weight| 15.8 kg (34.8 lbs)| 45.2 kg (99.6 lbs)| 32.7 kg (72.0 lbs)| 93.5 kg (205.7 lbs)
Construction| 15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood| 15 mm (5/8″) birch plywood| 18 mm (5/8″) birch plywood
Finish| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)| Semi-matte black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M10 x 8| M10 x 16| M10 x 8| M10 x 8
Accessories| | | TCS115-FP (WH)
fly plate kit for TCS115B TCS-FK2 (WH) inter-cabinet coupler kit for TCS115B with TCS122 or TCS152 TCS-FK3 (WH) inter-cabinet coupler kit for TCS115B
---|---|---|---

***** All third-party trademarks are the property of their respective owners. Their use neither constitutes a claim of the trademark nor affiliation of the trademark owners with Music Tribe.
Product names are mentioned solely as a reference for compatibility, effects, and/or components.

Important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model.
   Faulty fuses must be replaced with fuses of the same type and rating without exception.

Hereby, Music Tribe declares that this product is in compliance with Directive
2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation
519/2012 REACH SVHC and Directive
1907/2006/EC and this passive product is not applicable to
EMC Directive 2014/30/EU, LV Directive 2014/35/EU.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark

References

• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>