Turbosound TFM122M-AN Co-axial 2500 1100 Watt User Guide

: June 5, 2024
: Turbosound

Table of Contents

Important Safety Instructions
Unpacking the Loudspeaker
Controls
Networking capability
Networked mains power
TFM-AN/TFX-AN DSP Menu Structure
Important information
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Turbosound TFM122M-AN Co-axial 2500 1100 Watt User Guide

Important Safety Instructions

Caution: Risk of Electric Shock!: Do not Open

**** Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

****This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel.

Caution
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution
These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Use only attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
Do not install in a confined space, such as a book case or similar unit.
Do not place naked flame sources, such as lighted candles, on the apparatus.
Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.

Thank you for choosing a Turbosound loudspeaker product for your application. If you would like further information about this or any other Turbosound product, please visit our website atturbosound.com.

Unpacking the Loudspeaker

After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment.

Controls

Product Controls

LCD SCREEN displays the current DSP module and parameter settings.
PROCESS button steps through the DSP processing modules.
SETUP button steps through parameters within DSP processing modules.
EXIT button returns to the top-level DSP screen when pressed.
ENTER button saves changes and deactivates Edit mode when pressed.
ENCODER KNOB toggles between Graphic and Edit modes (when pressed) and changes parameter values (when rotated).
AUDIO INPUT combo jack accepts input signals using XLR, balanced ¼” TRS or unbalanced ¼” TS connectors.
AUDIO LINK XLR connector provides an un-processed copy of the AUDIO INPUT signal.
ULTRANET IN RJ45/Neutrik etherCON jack for connection to additional ULTRANET-equipped devices.
ULTRANET THRU sends out unprocessed digital audio from the ULTRANET IN connector to additional ULTRANET-equipped devices.
USB connection enables firmware updates and remote control over parameters via computer. Please visit turbosound.com to download DSP control software for your computer.
AC LINK OUTPUT (TFM-AN Series only) connects power to other devicesusing power cables with Neutrik powerCON twist-locking connectors.
POWER switch turns the unit on and off.
AC INPUT (TFM-AN Series only) accepts power connections from power cables fitted with Neutrik powerCON twist-locking connectors.
POWER (TFX-AN Series only) connection accepts power from the included IEC cable.

Networking capability

All TFM-AN/TFX-AN powered loudspeakers offer remote control via USB. The USB connection allows the user to configure and monitor all DSP parameters using dedicated software for PC.

The DSP firmware can also be updated via the USB connection. Visit turbosound.com for the latest firmware version.

TFM-AN/TFX-AN speakers also offer proprietary ULTRANET networking capabilities through the ULTRANET IN and ULTRANET THRU connections using CAT5 cables with RJ45 connectors. ULTRANET allows the user to transmit unidirectionally up to 16 independent channels of 24-bit audio throughout the TFM-AN/TFX-AN system, as well as other ULTRANET-equipped devices such as digital mixers and personal monitor systems. Up to 7 devices can be connected in series on a single ULTRANET cable.
Networking capability

Networked mains power

TFM-AN loudspeakers also facilitate networked transmission of mains power using power cables with Neutrik powerCON locking power connectors. To set up networked mains power between TFM-AN loudspeakers, first run a power cable terminating in a powerCON connector to the AC INPUT connector on the rear panel.

To power additional speakers downline, run power cables equipped with powerCON connectors at both ends from the first speaker’s AC LINK OUTPUT to the AC INPUT of the next TFM-AN loudspeaker in series.

The maximum number of linked systems depends on the AC supply voltage as well as the maximum current draw of the individual systems in the power chain. When linking a power chain, make sure that the integrated connectors as well as the supplied AC mains cable are never overloaded. If you are uncertain how to calculate the total current draw, please contact your dealer.
Networked mains

| | Fullrange
None| Function
Sets the frequency response to the default setting.
---|---|---|---
| | Vocal| Sets the frequency response to give an ideal monitor speaker for vocals.
| | Speech| Sets the frequency response for optimal speech intelligibility.
| | Playback| Sets the frequency response ideal for music playback.
| | User| Lets you define your own frequency response setting by entering the corresponding sub-menu.
| | None| Unit is set for default full-range / subwoofer reproduction.
| | HP 120 Hz| Preset with 120 Hz, 24 dB/octave filter for crossover between subwoofer and full-range speakers.
| | HP 100 Hz| Preset with 100 Hz, 24 dB/octave filter for crossover between subwoofer and full-range speakers.
| | User| User crossover sub menu for combination with other full- range or subwoofer speaker systems.
| | Freq| Select the desired crossover frequency: Fullrange systems: 75 Hz to 400 Hz.
| | Phase| Adjust the absolute phase (0° or 180°).
| | Auto| Automatically sets as many filters as required. Whenever a new feedback frequency is discovered, the first filter will be released to attenuate the new frequency, and so forth.
| | Single| Activates the FBQ (feedback detection) functionality, up to 8 feedback filters.
| | Learn| Automatic procedure which searches for feedback frequencies and locks settings after all 8 filters have been set.
WARNING!
Please use ear protection during this procedure. The feedback signal may approach the system’s maximum level, which may cause hearing damage!
| | Reset| Resets all filters.
| | Input| Lets you choose the audio input source. Choose between Local (analogue Input) or ULTRANET (e.g., P16 monitoring system or M32 audio via ULTRANET).
| | Volume| Adjusts the input gain. With ULTRANET digital inputs over a range from +10 dB to -30 dB. With analogue input from 0 dB to -∞ dB.
| | Stand| For positioning the speaker on a pole mount stand (full-range) or on the floor (subwoofer).
| | Floor| For positioning the speaker on the floor as a monitor speaker (wedge).
| | Corner| For positioning the speaker in a corner next to the ceiling (fixed install); For positioning the speaker in a corner (subwoofer).
| | Delay| Adjusts the amount of delay (max 300msec = 103.08m or 338.19 feet).
| | Unit| Selector between msec, meter and feet.
| | Limit| Adjust the limiter threshold for the input signal (from OFF down to -30 dB). This threshold adjustment allows you to set a max output power which is below the speaker system’s rated max output.
| | Version| Displays the installed firmware version.
---|---|---|---
| | 1. – 20.| To load a specific preset, turn the encoder to select the desired peset’s number, and then either the ENTER button or the encoder. When asked to confirm press the encoder again or EXIT to abort.
| | 1. – 20.| To save a preset choose the respective preset slot and press ENTER or the encoder.
| | Save Preset| Name the preset by choosing the characters with the encoder and pressing to confirm each character. When finished, press the ENTER button to save the preset.
| | Contrast| Adjust LCD panel contrast, The default contrast value is 15.
| | Screen| ON: LCD screen saver (default) turns on automatically after approx. 2 minutes. OFF : LCD turns off automatically after approx. 5 minutes.
| | Logo| OFF: Deactivates front panel logo illumination. ON: Activates front panel logo illumination. LIMIT: Logo will light up when the limiter is active.
| | Lock| Lock the device and create a password by choosing the password characters with the encoder and pressing to confirm each character. When finished press the ENTER button. Unlock the device by entering the password or connecting the unit via USB to a PC running proprietary remote software. The software does not require a password.
| | Warning| In case of overheating, an alert appears on the LCD screen, and the amplifier will shut down until the unit cools.

LCD Graphic Indicators

To help the user immediately recognize that a parameter has been selected and changed from the initial default setting, the parameter’s related text on the top-level screen will invert and change to black text on a white background. As an example, the following screenshots show how the text for the EQ function changes when the TFM-AN/TFX-AN default EQ setting has been changed:
Menu Structure

This indicator function occurs only on the main DSP menu level and works for all DSP-related functions, except for the LOAD, SAVE and SETUP sub-sections on the second page of the top-level SETUP menu.

| TFM122M-AN (POBLT)| TFM152M-AN (POBLU)|

TFX122M-AN (POBMU)

---|---|---|---
System| | |
Frequency response| 70 Hz — 18 kHz ±3 dB
63 Hz — 20 kHz -10 dB| 60 Hz — 18 kHz ±3 dB
50 Hz — 20 kHz -10 dB| 75 Hz — 18 kHz ±3 dB
68 Hz — 20 kHz -10 dB
Nominal dispersion| 60° H x 40° V @ -6 dB points, rotatable| 60° H x 40° V @ -6 dB points, rotatable| 60° H x 40° V @ -6 dB points, rotatable
Maximum SPL| 130 dB peak| 132 dB peak| 125 dB peak
Crossover type| Active| Active| Active
Transducers| 1 x 12″ (315 mm) LF driver
1 x 1.4″ (33 mm) HF compression driver| 1 x 15″ (393.5 mm) LF driver
1 x 1.4″ (33 mm) HF compression driver| 1 x 12″ (311.5 mm) LF driver
1 x 1″ (25.4 mm) HF compression driver
Limiter| Independent HF, LF, peak and rms| Independent HF, LF, peak and rms| Independent HF, LF, peak and rms
Amplifier| | |
Maximum output power| 2500 W| 2500 W| 1100 W
Type| Class-D| Class-D| Class-D
Protection| Short circuit, thermal| Short circuit, thermal| Short circuit, thermal
Connectors| | |
Input /Link Sensitivity Input impedance Maximum input level| 1 x combo jack/XLR, 1 x XLR -2 dBu 40 Idl balanced +12.5 dBu| 1 x combo jack/XLR, 1 x XLR
-2 dBu
40 Idl balanced
+12.5 dBu| 1 x combo jack/XLR, 1 x XLR
+1 dBu
40 k0 balanced
+12.5 dBu
Ultranet input/link| 2 x R145| 2 x R145| 2 x RJ45
Mains Supply| Neutrik powerCON input 20A and link 15At| Neutrik powerCON input 20A

and 15At

I d link

| Standard IEC recepticle

h

UK / Australia / Europe Korea / China

Japan

| 120 V—, 60 Hz (T 15 A H 250 V)
220-240 V—, 50/60 Hz (T 10 A H 250 V)
220-240 V—, 50/60 Hz (T 10 A H 250 V)
100 V—, 50/60 Hz (T 15 A H 250 V)| 120V—,60 Hz(T 15 AH 250 V)
220-240 V-150/60 Hz (T 10 A H 250 V)
220-240 V-150/60 Hz (T 10 A H 250 V)
100 V—, 50/60 Hz (T 15 A H 250 V)| 120 V—,60 Hz(T8 AH 250 V)
220-240 V—, 50/60 Hz (T 4 A H 250 V)
220-240 V—, 50/60 Hz (T 4 A H 250 V)
100 V—, 50/60 Hz (T 8 A H 250 V)
| Enclosure| |
Dimensions (HWD)| 302 x 452 x 504 mm
(11.9 x17.8 x19.9″)| 351 x 530 x 565 mm
(13.8 x 20.9 x 22.3″)
Net weight| 16.5 kg (36.3 lbs)| 20.2 kg (44.5 Ibs)
Construction| 15 mm (5/8″) birch plywood +
polypropylene plastic| 15 mm (5/81 birch plywood +
polypropylene plastic
Finish| Semi matt black paint| Semi matt black paint
Grille| Powder coated perforated steel| Powder coated perforated steel
Flying hardware| N/A| N/A

*independent of limiters and driver protection circuits.
†Only qualified personnel are allowed to modify the AC-Main cord and to adhere to all applicable national standards.
**Power consumption for a single device only

Important information

Register online. Please register your new MusicTribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
Malfunction. Should your MusicTribe Authorized Reseller not be located in your vicinity, you may contact the MusicTribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 5270 Procyon Street,
Las Vegas NV 89118,
United States
Phone Number: +1 702 800 8290

TFM-AN/TFX-AN SERIES

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warning: Operation of this equipment in a residential environment could cause radio interference..

Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU,Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.

Full text of EU DoC is available at https://community.musictribe.com/

EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark