BERG MX 14 Hand Mixer Instruction Manual

MX 14 Hand Mixer
Instruction Manual

MX 14 Hand Mixer

WARNING:
For your personal safety. READ and UNDERSTAND before using. Save these instructions for future reference.

|

SERVICE
New products at www.bergtectool.com
Learn more about our interesting New developments on our website. she always find the current one there Complete catalog for download. Just look in. WARRANTY
In the case of warranty cases, we provide a free one Repair or, if necessary, a free replacement. For Guarantee case please always keep your filled out Warranty card and proof of purchase ready.
REPAIR SERVICE
We are always bemiht the tools again ready for use as quickly as possible. In spite of the highest quality standards  also a tool can sometimes in hard work on the construction site strike. In the event of a repair, a Estimate to help you decide whether should be repaired or not. We’re always around fair and cost-effective processing.
ENVIRONMENTAL PROTECTION
When developing products, we always pay attention sure that we meet all appropriate environmental standards note and you flawless  and deliver safe products. We’ll be happy to dispose of it also your old devices in an environmentally friendly way materials back into the economic cycle.

Technical Data

Electronic Power Mixer

II
Certification| CE / UKCA| CE / UKCA
Thread for fixing the Tool| M 14 x 2| M 14 x 2
Mixing Paddle (7 max.)| 140 mm| 160 mm
Electronic Speed Control| ✓| ✓
Net Weight| 5.6 kg| 6.2 kg

Control Elements

• Accessories supplied with the instrument may differ from the parts depicted or described in this instruction.

Safety Precautions

Safe operation of this machine is only possible when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

• The machine is not qualified for operation in environments where danger of explosion exits.
• The machine must not be damp and must not be operated in a wet environment.
• Always inspect cable and plug before using machine. Only have damage repaired by a qualified professional.
• Connect machines that are used in the outside-area via a residual current circuit breaker. Use only extension cables that are intended for outdoor use and are protected against splash water.
• Put the plug into the mains socket only when the machine is switched off.
• Always lay the cable away from the machine towards the rear.
• Take care of long hair and fashion accessories; work in properly buttoned-up clothes, without freely flowing parts.
• When working with the machine, always hold it firmly with both hands and provide for a secure stance. Secure the vessel with the mixed substance against moving on the floor.
• Tobe on the safe side, always use the handle (16 + 17). Consider possible reaction torque.
• Donot carry the machine by the power cord.
• Before any work on the machine itself, pull the mains plug.

If the cord is damaged, it should be replaced by the manufacturer or an authorized service department to avoid dangers.

Starting Operation and Use

Check if the data on the nameplate is corresponding with the actual mains voltage. Instrument scheduled for 230V can be plugged to 220V/240V mains.
Improper use may damage the Instrument. Observe therefore these instructions:

• Use just mixing paddles up to the specified diameter.
• Load the instrument in such a way that the speed would not drop considerably or that it would stop.

Fixing a mixing-paddle:
Screw the mixing-paddle (64) with thread M 14 x 2 as far as possible in the spindle hole and tighten properly with an open-end wrench (62), which is included.
Switching On and Off:
By pressing the switch button (20) to start machine, simultaneous pressing the lock-on switch for continuous operation. Pressing again the switch button to stop machine.
Unloading the mixing-paddle:
Fit a flat open-end wrench (62) on spindle flats (65) of the tool and unscrew the mixing-paddle (64) from the spindle by turning it to the left.

Maintenance

• This power tool normally requires no maintenance; from time the ventilation holes on the motor housing (3) should be cleaned out.
• After approx. 50 hours of operation, check the motor brushes and replace if necessary. Clean the motor housing.
• After approx. 200 hours of operation, renew the grease filling in the gearbox.

 To verify that the protective insulation remains intact, the machine must be subjected to a technical safety test afterwards. For this reason, this work must be performed exclusively by a professional workshop.

Environment Protection

Do not open worn out machines and return to the collection facilities provided for recycling.

Service

See enclosed sheet. (Guarantee Card)

Storage

The unit should be stored in a dry place where it is protected against freezing.

Guarantee

We guarantee appliances in accordance with statutory/country-specific regulations. Proof of purchase by invoice or delivery note. The guarantee is only valid with a stamp of your dealer on the guaranteecard, which shows the date of purchase and the serial number of the item. The data on your bill or delivery note must be similar to the data on the guarantee card.

Noise / Vibration Information

Measured values determined according to EN 62841.
→Wear ear protection!

CE / UKCA Declaration of Conformity

We declare under our sole responsibility that this product is in conformity with the following standards or standardization documents:

2006/42/EC:| EN 62841-1:2015+AC:15
EN 62841-2-10:2017
EK9-BE-88(V2):2020
---|---
2014/30/EU:| EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019

Fabian Berg
Authorized Person for technical documentation, General Manager
Cologne, July 2021
UK Authorised Representative:
Authorised Rep Compliance
Arc House
Thurnham
Lancaster
LA2 ODT
BERG TECTOOL GmbH
Hermann-Heinrich-Gossen-Str. 3
50858 KélIn
Germany
Subject to modifications

  BERG TECTOOL GmbH
Hermann-Heinrich-Gossen-Str. 3
50858 K6In
Germany
Fon: +49 (0) 221 – 964966 – 0
Fax: +49 (0) 221 – 964966 – 22
www.bergtectool.com
bt@bergtectool.com

Documents / Resources

| BERG MX 14 Hand Mixer [pdf] Instruction Manual
MX 14, MX 19, MX 14 Hand Mixer, Hand Mixer, Mixer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>