BERG MX 19 Hand Mixer Instruction Manual

: June 3, 2024
: BERG

Table of Contents

Technical Data
- Control Elements
Safety Precautions
Starting Operation and Use
Maintenance
Guarantee
CE / UKCA Declaration of Conformity
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BERG MX 19 Hand Mixer Instruction Manual

Technical Data

Electronic Power Mixer

TECHNICAL DATA BERG MX 14 BERG MX 19

Power Input| 1400 W| 1850 W
Voltage| 2301/150Hz – 110V/60Hz| 230V/50Hz – 110V/60Hz
Nm| 21| 45
Number of Gears| 1| 2
No-Load-S peed (m in-‘)| 0-800| 180-460 / 300-750
Ampille (110V)| 13,50| 15,00
Am pOe (230V)| 6.50| 8.50
Protection! Class of Protection| Double Insulation I II| Double Insulation / II
Certification| CE I UKCA| CE / UKCA
Thread for fixing the Tool| M 14 x 2| M 14 x 2
Mixing Paddle (7 max.)| 140 mm| 160 mm
Electronic Speed Control| ✓| ✓
Net Weight| 5 6 kg| 6.2 kg

Control Elements

20 Switch / Arresting pin
16+17 Handle
03 Motor Housing
62 Open-End Wrench*
64 Mixing-Paddle*
65 Spindle flats

Accessories supplied with the instrument may differ from the parts depicted or described in this instruction.

Safety Precautions

Safe operation of this machine is only possible when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

The machine is not qualified for operation in environments where danger of explosion exits.
The machine must not be damp and must not be operated in a wet environment. o Always inspect cable and plug before using machine. Only have damage repaired by a qualified professional.
Connect machines that are used in the outside-area via a residual current circuit breaker. Use only extension cables that are intended for outdoor use and are protected against splash water.
Put the plug into the mains socket only when the machine is switched off.
Always lay the cable away from the machine towards the rear. o Take care of long hair and fashion accessories; work in properly buttoned-up clothes, without freely flowing parts.
When working with the machine, always hold it firmly with both hands and provide for a secure stance. Secure the vessel with the mixed substance against moving on the floor.
To be on the safe side, always use the handle (16 + 17). Consider possible reaction torque.
Do not carry the machine by the power cord. o Before any work on the machine itself, pull the mains plug.

If the cord is damaged, it should be replaced by the manufacturer or an authorized service department to avoid dangers.

Starting Operation and Use

Check if the data on the nameplate is corresponding with the actual mains voltage. Instrument scheduled for 230V can be plugged to 220V/240V mains.

Improper use may damage the Instrument. Observe therefore these instructions:

Use just mixing paddles up to the specified diameter.
Load the instrument in such a way that the speed would not drop considerably or that it would stop.

Fixing a mixing-paddle:

Screw the mixing-paddle (64) with thread M 14 x 2 as far as possible in the spindle hole and tighten properly with an open-end wrench (62), which is included.

Switching On and Off:

By pressing the switch button (20) to start machine, simultaneous pressing the lock-on switch for continuous operation. Pressing again the switch button to stop machine.

Unloading the mixing-paddle:

Fit a flat open-end wrench (62) on spindle flats (65) of the tool and unscrew the mixing-paddle (64) from the spindle by turning it to the left.

Maintenance

This power tool normally requires no maintenance; from time the ventilation holes on the motor housing (3) should be cleaned out.
After approx. 50 hours of operation, check the motor brushes and replace if necessary. Clean the motor housing.
After approx. 200 hours of operation, renew the grease filling in the gearbox.

To verify that the protective insulation remains intact, the machine must be subjected to a technical safety test afterwards. For this reason, this work must be performed exclusively by a professional workshop.

Environment Protection
Do not open worn out machines and return to the collection facilities provided for recycling.

Service
See enclosed sheet. (Guarantee Card)
Storage

The unit should be stored in a dry place where it is protected against freezing.

Guarantee

We guarantee appliances in accordance with statutory/country-specific regulations. Proof of purchase by invoice or delivery note. The guarantee is only valid with a stamp of your dealer on the guarantee-card, which shows the date of purchase and the serial number of the item. The data on your bill or delivery note must be similar to the data on the guarantee card.

Noise I Vibration Information

Measured values determined according to EN 62841.
Wear ear protection!