MORRIS MOR-TBH-3FT Tubular Heater Instruction Manual
- June 11, 2024
- MORRIS
Table of Contents
MORRIS MOR-TBH-3FT Tubular Heater
Tubular
Heater: MOR-TBH-1FT/ MOR-TBH-2FT/MOR-TBH-3FT/ MOR-TBH-4FT
YOU SHOULD READ THE MANUAL CAREFULLY BEFORE USING, AND KEEP THE MANUAL FOR
FUTURE REFERENCE.
DISPOSAL
This symbol indicates that this product must not be placed in general
household waste. It should be sent to a separate recycling facility for
recovery, check Local Authorities for details.
By responsible recycling and separating this product from other household
waste it will help protect the environment and human health, as the volume of
waste sent to incinerators or land-fills will be reduced and natural resources
conserved.
Please Note: During the first use the heater may emit a small amount of vapour
which is perfectly normal. The reason for this is the heating wire element is
coated with some lubricant oil during the production process. This will stop
after approx. 5 minutes after the first use and is not a safety concern.
Read all the instructions prior to use.
Safety Regulations
- The tubular heater is not suitable for use outdoors in damp weather.
- Do not submerge into water.
- Place in a safe place away from flammable objects.
- Do not place flammable liquids or gasses near the heater.
- Do not place the heater directly below the socket outlet.
- Do not let the power cord over hang or touch the tube.
- Keep out of reach of children and animals – product gets hot to touch.
- This is not a toy.
- Switch off appliance when not in use.
- Do not hold the tubular heater by the cord.
- If using an extension cord it must be as short as possible and fully extended.
- Check heater regularly if using with a timer or any other device that switches the tubular heater on or off automatically.
- This leaflet should be retained for instructions on use.
Cleaning
Ensure product is unplugged from the mains. Ensure product is completely cold.
Wipe with a damp cloth, then finish by drying with a soft cloth. DO NOT use
abrasive cleaning powders, clothes or metal polishes on any part of the
tubular heater as this will cause damage.
Thermal Cut-out
The appliance is fitted with a thermal cut-out. Once the tubular heater has
cooled down it will re-set itself automatically. It will then switch on and
off until the reason for overheating has been removed.
Operation
Notice: DO NOT SWITCH POWER ON TO THE HEATER UNTIL IT IS SECURELY
MOUNTED.
- Step 1. Install the bracket as the picture shows.
- Step 2. Fix the tubular heater on the wall or on the floor like the following picture shows.
Tubular Heater Notice:
- The heater is fitted with a safety device which will switch off the heater in case of accidental overheating.
- To reset, turn the heater off at the switch for a few minutes to allow the unit to cool down.
- Make sure that any causes of overheating, such as obstructions, are removed and plug the appliance in again.
- Turn the switch off when it is summer or nobody at home or no need to keep heating, it is energy saving and safer.
Tubular heater Specifications
Model No.| Power| Electrical Supply| IP Rating| Product Length (mm)| Product
Size (mm)
---|---|---|---|---|---
MOR-TBH-1FT| 60W| 220-240V ,50 Hz| IP55| 300mm| 3109885
MOR-TBH-2FT| 120W| 220-240V ,50 Hz| IP55| 609mm| 6109885
MOR-TBH-3FT| 180W| 220-240V ,50 Hz| IP55| 900mm| 9109885
MOR-TBH-4FT| 240W| 220-240V ,50 Hz| IP55| 1200mm| 12009885
Warranty
This product is guaranteed under warranty and covers defects in material or
workmanship from 1 year of date of purchase. The original bill of purchase
(with purchase date) must be submitted.
The warranty will not apply in cases of: Misuse: by non-compliance of the
instructions, normal wear and tear, incorrect use, e.g. overloading,
non-approved accessories, force or damaged caused by external forces, if the
plug has been tampered with or removed, partially or completely dismantled
product, or interference by non-qualified persons.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>