FEELWORLD F970 10.1 Inch 3D LUT Touchscreen Monitor User Manual
- June 3, 2024
- FEELWORLD
Table of Contents
10.1″ 3D LUT Touchscreen Monitor
Daylight Viewable|F970 Install and Power Kit
User Manual
F970 10.1 Inch 3D LUT Touchscreen Monitor
Foreword
Thank you for purchasing our 10.1-inch Full HD touch screen monitor. Please
read this manual carefully before using the unit. Have a great experience!
CAUTION
- Please avoid the heavy impact and drop onto the ground when move the product.
- The screen of this product is made of glass.Keep away from injury if the screen is broken.
- Keep the product away from the heat source, and avoid the prolonged exposures to the sun as the LCD screen will be damaged.
- Please do NOT use chemical solutions to clean this product. Please wipe the monitor with a clean soft cloth to maintain the brightness of the surface.
- No adjustable components are in the monitor. Please do not take apart or repair the unit by yourself, to avoid the damage of the product.
Key Features
- 10.1-inch 1920×1200 full HD IPS screen
- Touch screen menu operation, improve shooting efficiency
- 2000nits daylight viewable (Light Sensor)
- New menu interface, more intuitive and intelligent
- Dual HDMI inputs support up to 4K@60Hz, 3G-SDI(optional)
- Support HDR monitoring, what you see is what you get
- Support 3D LUT Log to REC.709 and user 3D LUT upload(up to 50)
- Sony F970 external install and power kit design can be used to install and supply power to external equipment, easy to install and disassemble, simplify your photography equipment.
- With Waveform, Vector scope, Histogram, Focus Assist, Monochrome etc. functions, can help you accurately exposure and focus every shot.
- Stereo Earphone output
- DC 8V power out to power your DSLR camera or mirrorless camera
- Built-in Tally Indicators (Red, Green, Yellow)
- Dual F970 battery slots
Product Description
1.1 Button Instruction
- Power/Touch Function Button:Long press to turn on/off power; short press to turn on/off the screen touch function.
- F1 ~ F3: Custom function buttons
- Light Sensor: The backlight mode under the icon is set to Auto, and the brightness of the backlight can be adjusted automatically by the light sensor.
- MENU: See details: 2.2 MENU Wheel Menu Operation in 2. Menu Operation Instruction.
1.2 Port Instruction
- SD Card Slot 3DLUT upload via SD card and for firmware upgrade
- Power/Touch Function Button Long press to turn on/off; short press to turn on / off the screen touch function.
- F970 External Install and Power Kit
- 3.5mm Headphone Jack
- DC OUT 8V Power Output Connect the optional dummy battery cable to power camera.
- DC 12V Power Input
- HDMI Signal Output
- HDMI Signal Input 1
- HDMI Signal Input 2
- SDI Signal Output (Optional)
- SDI signal input(Optional)
- Tally Light Input
1.3 Power Supply Way
- The rear cover of the monitor is equipped with dual F970 battery plate, which is applicable to F970 series of batteries.
Sony F970 battery plate for battery of Sony DV:
Sony F970 F960 F950 F930 F770 F750 F730 F570 F550 F530 series
Remark: It is recommended to use standard original F970 batteries. Different specifications of the battery have different capability. The working time for the monitor will be different. Higher capability (working time) will be longer. Please take off the battery from the monitor if you don’t use the monitor in a long time.
● Battery switching instruction
- When the battery/batteries is/are placed in the battery slot(s), battery icon will appear on the upper right of the screen.
- White battery icon: working; Gray battery icon: not working.
- Manually switching: Double-tap the gray battery icon and it will be switched to a working state in about 3 seconds, then it will be turned white.
- Automatically switching: Automatically switch to another charged battery when one battery is exhausted.
(2) DC IN 12V: DC power input, polarity as the input power, Barrel (5.5mm
outer, 2.1mm inner) at the bottom of the monitor, DC 7~24V Input.
(3) DC OUT 8V : DC power output interface, polarity as the output power
Barrel output for powering your camera with a separately available DC coupler
via adaptor (NP-FW50 Sony & LP-E6 Canon&DMW-BLF19 Panasonic). More adapters
coming soon.
1.4 Sony F970 Install and Power Kit
A Sony F970 external install and power kit design is added to the back of the
monitor. The external kit can be used to install and install the external
equipment, like wireless transmitter, LED light, video converter and others
which can be powered by Sony F970 battery. The kit has two cross grooves, you
can adjust the position of the external device by loosening 2 screws up and
down / left or right, or install the kit upside down. When you don’t need the
kit, you can loosen the screws and remove the kit.
Note: Before disassembling the kit, make sure that the monitor is turned
off, and then remove the battery or power adapter.
(1) Just move the kit: Loosen 2 screws, and then adjust up / down / left
/ right.
(2) Steps to remove the kit:
①. Loosen the 2 screws.
②. Use both hands to move the kit up.
③. Move the round holes to the corresponding 2 screws.
(You can also install the kit upside down.)
④. Then gently lift the kit upwards and carefully disassemble the 2P power
cord.
⑤. Then remove the 2 screws.
1.5 Mount Points
There are (3) ¼-20 thread points (bottom, right & left) can be easily
connected to the hot shoe mount, tripod fixed installation.
U-shape Bracket Mounting
1.6 TALLY Indicator Connection
Indicator Color | Pin connect |
---|---|
Green | 5-Jan |
Red | 5-Jun |
Yellow | 5-Sep |
Menu Operation Instruction
After the monitor is properly connected to the power supply, the button display(red indicating). Long press button to turn on the monitor and turns yellow indicating. After the signal is connected, the button turns green indicating. After startup, short press button to select to turn the screen touch function on or off.
2.1 Touch Screen Menu Operation (turn on the screen touch function)
- Double-click on the screen to open the main menu (show on the left side of the screen) and click on the corresponding menu to display the secondary menu. You can enter the corresponding function option and click directly to select or set. Click the touch screen to exit the menu.
- When the menu is not displayed, swipe up from the bottom of the screen to open the shortcut menu, and click on the corresponding menu box to open or set the corresponding function. Click the hide icon to close detailed parameters, and click the menu icon to display detailed parameters.
- When the menu is not displayed, on the left side of the screen (1/2 split screen), you can directly adjust the brightness of the screen backlight; on the right side of the screen (1/2 split screen), you can directly adjust the volume.
Figure:
2.2 MENU Wheel Menu Operation
- When the menu is not displayed, directly rotate the wheel to backlight or volume adjustment. The wheel option can be set to backlight or volume in the menu .
- Short press the MENU wheel to open the main menu (on the left side of the screen). Rotate the wheel to select the secondary function menu. After selecting it, press the wheel, then rotate the wheel to select or set the option function.
- Long press th e MENU wheel to open the shortcut menu (below the screen), rotate the wheel to select the shortcut menu option, press the wheel to directly turn on/off the function, if you press the parameter selection, repeat the above operation. Tap the screen or long press the wheel to exit.
2.3 MENU UI Instruction
Menu Function Instruction
Assist
Analysis| OFF, ON
After turning on, waveform, vector, histogram and embedded audio will be
shown.
---|---
**| OFF, ON
Type: RGB, YUV, Y
Waveform| This essential feature assists with the calibration of
professional video cameras. It shows the overall brightness of the image
assisting the video professional in correcting exposure. The waveform feature
also checks the evenness of the lighting when lighting a chromakey or
background.
---|---
Vectorscope| OFF, ON
Shows how saturated the image is and where the pixels in the image land on
the color spectrum.
Histogram| Histogram: OFF, ON
Y Histogram: OFF, ON RGB Histogram: OFF ON
Focus Assist| OFF, ON
Focus Color: Yellow, M agenta , Cyan, Red, Green, Blue, White After
turned on, the Focus Level (1 ~ 8) and Focus Color can be
adjusted.
Audio Meters| OFF, ON
Zebra| OFF, ON
After the Zebra is turned on, the Zebra Value (0IRE ~ 100IRE) can
be adjusted.
Check Field| Monochrome Display: OFF, ON Display Color: red, green,
blue, gray
False Color| OFF, ON
Type: Spectrum, ARRI
Tally| OFF, ON**
Marker
Crosshatch| OFF, ON
Type: 3×3, 4×4, 5×3, 5×5, 6×4, 6×6
Color: Yellow, M agenta , Cyan, Red, Green, Blue , White
---|---
Safe Areas| OFF, ON
Marker Line Type: 70%, 80%, 90%, 16:9, 16:10, 4:3, 5:4, 1:1,
1.91:1.1, 4:5, 9:16: 1.85:1, 2.35:1
Marker Line Color: Yellow, M agenta , Cyan, Red, Green, Blue, White
Crosshair| OFF, ON
Marker Line Color: Yellow, M agenta , Cyan, Red, Green, Blue, White
Cinema Guides| OFF, ON
Marker Line Type: 16:9, 16:10, 4:3, 1.85:1, 2.35:1, 2.41:1, 1.9:1,
5:4, 1:1.9
Marker Line Color: Yellow, M agenta , Cyan, Red, Green, Blue, White
After the Marker Mat is turned on, the Marker Mat Alpha (0%, 25%,
50%, 75%) can be adjusted.
Image
Scan Mode | Under Scan, Over Scan |
---|---|
Aspect Ratio | **OFF, ON |
Type: Auto, 16:9, 16:10, 4:3, 5:4, 1.85:1, 2.35:1, user
Aspect Ratio| Under the “ user ”, you can customize the Video Width
(100% ~ 300%) , Video Height (100% ~ 300%)
---|---
Anamorphic| Lens: OFF, ON
Lens Type: 1.25x, 1.33x, 1.5x, 2.0x, 2.0x mag
** Mirror| Mirror: OFF, ON
Auto Mirror: OFF, ON
After turning on, the image will automatically adjust upside down.
Horizontal Mirror: OFF, ON
Vertical Mirror: OFF, ON
Zoom Times| Image Zoom: OFF, ON Zoom Times: 1.0x ~ 5.0x
Freeze| OFF, ON
Pixel to Pixel| OFF, ON
User Options
HDR| HDR: OFF, ON
Camera: After turning on, can choose Gamma and Gamut corresponding to
the camera RED, ARRI, Sony, Canon, Panasonic, Fujifilm, Bolex, ,
---|---
** LUT| LUT Switch: OFF, ON
SDI Out (LUT) : OFF, ON (with SDI interface version) Under the SDI
signal, you can choose whether to loop out the LUT after the LUT function is
turned on
LUT Import: OFF, ON
After copying the 3D LUT file to the SD card and inserting it into the SD
card slot, click ON or rotate the wheel to import the 3D LUT file. (Up to
50)
| Note: the chip should be faced up when inserting the SD card, and press
it after inserting to ensure that the SD card is fully inserted.
LUT List: display built in SLOG2, SLOG3, LOGC, VLOG and the custom
LUTs
---|---
****Display Setup| Brightness: 0~100 Contrast: 0~100 Saturation:
0~100 Hue: 0~100 Sharpness: 0~100
Backlight Mode: manual, Auto Under “Manual”, the Backlight (1 ~
100) can be adjusted manually.
Under “Auto”, the backlight is automatically adjusted by the light sensor.
** Color| Color Space: REC709, DCIP3, BT2020
Color Temp.: 5600K, 6500K, 9300K, User
Under the “ user ”, the red , green , and blue values of
the image can be adjusted (0~255)
System
**Wheel| Backlight, Volume
After selecting the wheel option, you can click Backlight or Volume , or
rotate the wheel to select one of the shortcut key to set it to the rotary
wheel adjustment (when the menu is not displayed).
---|---
****Shortcut| F1 Function, F2 Function, F3 Function Shortcut List:
Analysis, Waveform Type, Y Histogram, Audio Meters, Crosshatch Type, Marker
Line Type,
| Crosshair, Monochrome Display Color, False Color Type, Focus Level, Zebra,
Color Space, Color Temp., HDR, LUT Switch, Scan Mode, Aspect Ratio Type, Lens
Type, Pixel to Pixel, Mute, Input, Freeze, Auto Mirror, Tips
Set the shortcut function
****e.g.: Tap the menu select F1Function , then select one of
function on Shortcut List, such as “Analysis”. So when you exit menu, you
could press F1 directly on the front of panel to turn on “Analysis” function.
Same setting for F2, F3
---|---
Input| HDMI1、HDMI2、 SDI (with SDI interface version)
Language| English 、
OSD Setup| OSD Time: always, 15s, 30s, 45s
OSD Alpha: OFF, Lo, Mid, Hi
Volume| Mute: OFF, ON
Volume: 0~100
Power display**| OFF, ON
After turning on, the battery level will be displayed in the upper right
corner of the screen.
Firmware Update
| Firmware Update, Restore
After copying the update file to the SD card and inserting it into the SD
card slot, you can click Update or rotate the wheel to update.
Note: the chip should be faced up when inserting the SD card, and press
it after inserting to ensure that the SD card is fully inserted.
Restore: click Restore or rotate the wheel to restore the system.
Support Formats
SDI Input Support Format (SDI version)| 720p
(60/59.94/50/30/29.97/25/24/23.98) 1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/23.98) 2048x1080i (60/59.94/50)
2048x1080p (60/59.94/50/30/29.97/25/24/23.98)
---|---
SDI Output Support Format (SDI version)| 720p
(60/59.94/50/30/29.97/25/24/23.98) 1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/23.98)
HDMI Input/ Output Support Format| 480i/480p/576i/576p 720p
(60/59.94/50/30/29.97/25/24/23.98) 1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/23.98)
3840x2160p (60/50/30/29.97/25/24/23.98)
4096×2160p (60/50/30/29.97/25/24/23.98)
Technical Parameters
Panel Size | 10.1” touch screen |
---|---|
Resolution | 1920 × 1200 pixels |
Dot Pitch | 0.113(W) x 0.113(H) (mm) |
Aspect Ratio | 16:10 |
Brightness | 2000cd/m2 (Light Sensor) |
Contrast | 800:01:00 |
Viewing Angle | 85°/85°(L/R) 85°/85°(U/D) |
Backlight | LED |
Input | SDI (Optional), HDMI |
Output | SDI (Optional), HDMI, DC OUT 8.4V |
Audio | 3.5mm Stereo Headphone |
Power Input Voltage | 7~24V |
Power Consumption | ≦28W |
Unit Size | 242Lx165Hx23D (mm) |
Unit Weight | 810g |
Mount Points | (3) ¼-20 thread points (left, right, bottom) |
Working Temperature | -10℃~50℃ |
Storage Temperature | -20℃~60℃ |
Trouble Shooting
6.1 Only black and white or monochrome picture:
- please check saturation, brightness & contrast adjustment.
- Please check “Monochrome” is in black, white or monochrome image or other condition.
6.2 NO Image after put on the power
- Check if signal cable connecting is in good condition.
- Check signal cable connecting, and make sure to use the standard adapter to connect the monitor. If power is supplied by battery, please check if the battery is fully charged.
6.3 Earphone No sound
- Check if Volume control do not open, press the volume button, and try to increase the volume.
■ If there are still other problems, please contact with our related
technologists.
★ As we are improving product features and product performance, so if there is
any change on the specification without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>