feelworld F970 5.5 Inch High Bright Monitor User Manual
- May 15, 2024
- FEELWORLD
Table of Contents
feel world F970 5.5 Inch High Bright Monitor
Specifications:
- Screen Size : 5.5 inches
- Resolution: 1920×1080 Full HD IPS
- Brightness: 1600 nits
- Touch Screen : Yes
- Power Supply Modes : DC IN 12V, Type-C 5V, NP-F Battery Slot
- External Power Kit : Sony F970 Install and Power Kit
- Functions: Waveform, Vector scope, RGB Histogram, Focus Assist, Monochrome
- Audio Output : Stereo Earphone output
Product Usage Instructions:
- Installation and Setup
- Before using the monitor, ensure you have read the manual carefully. Avoid heavy impacts and prolonged exposure to heat or sunlight. Do not disassemble or repair the unit yourself.
- Powering On and Off
- To power on the monitor, long press the power button until the indicator turns yellow. When the signal is connected, the indicator will turn green. To power off, press the power button again.
- Navigating Menu and Settings
- Use the touch screen or buttons F1, F2, F3 to navigate through menus and settings. The functions of these buttons change based on whether the OSD is displayed or not.
- Connectivity
- Connect external devices using the various ports available, such as HDMI IN/OUT for video signals, DC OUT for powering cameras, and Type-C for power input.
- Battery Usage
- Install NP-F series batteries in the designated slot. Use the PUSH lock to secure the battery in place. Ensure proper handling of batteries to prevent damage.
FAQ
- Q: Can I use other battery types instead of the NP-F series?
- A : The monitor is designed to work with NP-F series batteries for optimal performance. The use of other battery types may not be recommended and could affect the functionality.
- Q: How do I adjust the brightness of the monitor?
- A : You can adjust the brightness through the settings menu accessed either via touchscreen controls or the designated buttons on the monitor.
- Q: What is the maximum resolution supported by the HDMI ports?
- A : The HDMI ports support up to 4K resolution at 30Hz.
Foreword
Thank you for purchasing our 5.5-inch high bright touchscreen monitor. Please read this manual carefully before using the unit. Have a great experience!
Caution
- Please avoid the heavy impact and drop onto the ground when move the product.
- The screen of this product is made of glass. Please do not drop the screen towards the ground. Keep away from injury if the screen is broken.
- Keep the product away from the heat source, and avoid prolonged exposure to the sun as the LCD screen will be damaged.
- To avoid damaging the product, please do not take apart or repair the unit by yourself without the adjustable components in the unit.
- In order to better maintain the LCD screen and protect the cover, please follow the following ways to avoid damage.
- Please refrain from using hard objects to hit the screen.
- Please do not force to wipe the screen.
- Please do not use the chemical solutions to clean the screen.
- Please do not spray any detergent on the screen.
- Please do not write on the screen directly.
- Please do not stick on the screen.
- Please simply wipe with a clean soft cloth and make sure no water on the screen.
Key Features
- 5.5-inch 1920×1080 full HD IPS screen
- Touch screen and intuitive button operation, meet different needs.
- High Brightness 1600nits, visible in sunlight
- Supports 3D LUT Log to REC.709 and user 3D LUT upload (up to 32).
- Sony F970 external install and power kit design can be used to install and supply power to external equipment, easy to install and disassemble, simplifying your photography equipment.
- With Waveform, Vector scope, RGB Histogram, Focus Assist, Monochrome etc. functions, can help you accurately expose and focus every shot.
- Multiple power supply modes, DC IN 12V, Type-C 5V and NP-F battery slot.
- Stereo Earphone output
- DC 8.4V power out to power your DSLR camera or mirrorless camera.
Product Description
- Front Panel Instruction
Indicator : After connecting the power, the indicator light is on (red). Long Press the button to turn on the monitor, it turns yellow. After the signal is connected, it turns green.
Rear Panel Instruction
- Battery Lock : The PUSH lock will lock after the battery is installed, please press PUSH first before removing the battery.
- NP-F Battery Slot : It is applicable to install an NP-F series of batteries.
- F970 Install and Power Kit : Installing the external equipment, like wireless transmitter, LED light, video converter, and others which can be powered by a Sony F970 battery. (The details see: 1.7 Sony F970 Install and Power Kit)
Top Button Instruction
Bottom Port Instruction
DC OUT 8.4V: DC power output interface, polarity as the output power Barrel output for powering your camera with a separately available DC coupler via adaptor (NP-FW50 Sony & LP-E6 Canon&DMW-BLF19 Panasonic). More adapters coming soon.
: 3.5mm earphone port output
DC IN 5V (Type-C): Type-C power input. It is recommended to be used for local power supply only. It is not recommended to connect other devices to provide loop-out power.
Left Port Instruction Left
- HDMI IN : V1.4, HDMI signal input, up to 4K@30Hz.
- HDMI OUT : V1.4, HDMI signal output, up to 4K@30Hz.
- DC IN 12V : DC power input, polarity as the input power
Power Supply Way
(1) The rear cover of the monitor is equipped with an F970 battery plate, which is applicable to the F970 series of batteries.
- Sony F970 battery plate for the battery of Sony DV: Sony F970 F960 F950 F930 F770 F750 F730 F570 F550 F530 series. It is recommended to use a standard original F970 battery.
When using a battery power supply: two power output interfaces (DC OUT 8.4V
interface and external install and power kit) can be connected to other
devices. When powering other devices, it is recommended to choose a battery
with a larger capacity, so the longer the use time.
Remark : Please take off the battery from the monitor if you don’t use
the monitor in a long time.
(2) The left side of the monitor has a DC 12V input power port (5.5mm outer, 2.1mm inner) and supports 7 ~ 24V wide voltage.
The DC power adapter needs to be purchased separately.
When using an external adapter input: two power output interfaces (DC OUT 8.4V
interface and external install and power kit) can be connected to other
devices. When powering other equipment, it is recommended to equip at least 3A
power adapter.
(3) The bottom of the monitor has a Type-C 5V input power port.
This port can be connected to the power bank for power supply and is not used for data transmission; it is recommended to be used only for local power supply, and it is not recommended to connect other devices to provide loop-out power.
Sony F970 Install and Power Kit
A Sony F970 external install and power kit design is added to the back of the monitor. The external kit can be used to install and install the external equipment, like a wireless transmitter, LED light, video converter and others which can be powered by Sony F970 battery.
The kit has two cross grooves, you can adjust the position of the external device by loosening 2 screws up and down / left or right, or installing the kit upside down. When you don’t need the kit, you can loosen the screws and remove the kit.
Note : Before disassembling the kit, make sure that the monitor is turned off, and then remove the battery or power adapter.
- Just move the kit: Loosen 2 screws, and then adjust up / down / left/right.
- Remove the external device: After the plug-in device is installed on the kit, if your plug-in device has a locking button, and it is more difficult to press it to remove it by hand, then you can use our assisting tool to disassemble it.
Steps to remove the kit:
- Loosen the 2 screws.
- Use both hands to move the kit up.
- Move the round holes to the corresponding 2 screws.(You can also install the kit upside down.)
- Then gently lift the kit upwards and carefully disassemble the 2P power cord.
- Then remove the 2 screws.
Install back to the kit : first screw the 2 screws back to the screw hole used to install the kit on the back of the monitor, install the 2P power cable to the cutout, then align the round hole of the kit with the screw, and then push the kit to the screw at the center of the kit cross, then tighten the screws.
Mount Points
(1) ¼-20 Thread Points
There are (4) ¼-20 thread points (top, bottom, right side & Back center) can be easily connected to the hot shoe mount, tripod fixed installation.
2) Tilt Arm Mounting
The monitor secures to your camera using the included Tilt Arm via shoe mount or 1/4″-20 thread.
- Allows the monitor to rotate 360 degrees for viewing convenience
- Secure and lightweight mounting via shoe mount or 1/4″-20 thread
- Includes a shoe mount of its own for accessories like a microphone, LED light, or wireless receiver, etc.
- There are two small dots on the tilt arm, which are aligned with the monitor for installation, the connection is more stable, just grab the monitor to rotate without loosening the screws.
Sunshade
First, lock the Sunshade Frame ②with the monitor tight ③.
Open the sunshade ①, and match the sticker on the sunshade inside to the
marked part of the sunshade frame ②, smooth and press 3 sides on the sunshade,
and then complete the sunshade installation ④.
Menu Operation Instruction
After the monitor is correctly connected to the power supply, the indicator light is on (red), long press turn on the monitor, the indicator light turns yellow, and after the HDMI signal is input, the indicator light turns green.
After turning on the power, you can press the TOUCH key to select turn on/off the touch function.
Touch screen menu operation (default touch screen is on)
- Double-click on the screen to open the main menu (on the left side of the screen) and click on the corresponding menu to display the secondary menu. You can enter the corresponding function option and click directly to select or set. Click the touch screen to exit the menu.
- When the menu is not displayed, swipe up from the bottom of the screen to open the shortcut menu, and click the function icon to open the corresponding function, click the icon again to exit the function. Swipe the shortcut menu left and right to select more functions. Click the touch screen outside the shortcut menu to exit the shortcut menu display.
- On the left side of the screen (1/2 split screen), you can directly adjust the brightness of the screen backlight; on the right side of the screen (1/2 split screen), you can directly adjust the volume.
Figure:
(2) Button Menu Operation
- When the menu is not displayed, directly press the “∨” or “∧”button to adjust the volume or backlight. You can set the left and right buttons in thein the Left Right Key Set of menu User Option
- Press the “MENU” button to enter the OSD main menu, press the MENU button again to enter the secondary menu, then press “∨” or “∧” button to select items, after selected press the MENU button to confirm and enter the function menu, press “∨”or “∧” button to select the corresponding function or adjust the parameters.
- Press the button to return/exit the menu
MENU Interface Instruction
Menu Function Instruction
Marker 
Image
User Option
System
How to Load LUT
- USB flash driver format FAT32
- Max Files Limit Maximum 32 Lut files
File requirements
- The LUT file format suffix should be .cube
- Single file not exceeding 7.9Mb
- Support LUT-3D-Size 16,17,32,33,64,65
- Make sure the USB flash driver is inserted to Type-C to the USB adapter and connected to the TYPE-C interface of the monitor
- Enter the main menu –LUT–Lut Import — click Confirm to load the monitor will auto-detect the USB flash driver If there is a valid lut file in the USB flash driver, the monitor will load lut files and show “[n] name. The [n] shows the quantity number. The “name” should in lut files’ name. If load successful, the screen will show “complete[n]”. [n] Stands for the quantity number for lut files should be under 32.
Remark: LUT file name must be English or Arabic numerals
Steps for loading
PS: How to clear up the imported LUTs?
Insert an empty USB flash driver to the monitor, enter the main menu
–LUT–Lut Import — click Confirm, the imported LUTs will be clear up.
Technical Parameters
Trouble Shooting
Only black and white or monochrome pictures:
- please check saturation, brightness & contrast adjustment.
- Please check “Check Field” is in black, white or monochrome image or other condition.
NO Image after putting on the power
- Check if the signal cable connecting is in good condition.
- Check the signal cable connecting, and make sure to use the standard adapter to connect the monitor. If power is supplied by the battery, please check if the battery is fully charged.
Earphone No sound
Check if Volume control do not open, press the volume button, and try to increase the volume.
- If there are still other problems, please contact with our related technologists.
- As we are improving product features and product performance, so if there is any change on the specification without prior notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>