Pyle PLMRW10 10-Inch Outdoor Marine Audio Subwoofer User Manual
- June 3, 2024
- Pyle
Table of Contents
Pyle PLMRW10 10-Inch Outdoor Marine Audio Subwoofer
Specifications
- SPEAKER SIZE: 10 Inches
- SPEAKER AMPLIFICATION TYPE: Passive
- WATER RESISTANCE LEVEL: Waterproof
- MAXIMUM OUTPUT POWER: 500
- PEAK POWER: 500 watts
- IMPEDANCE: 4ohm
- FREQUENCY RESPONSE: 25-2.5K Hz
- OVERALL DIAMETER: 6”
- MOUNTING DEPTH: 60”
- WEIGHT: 17 lbs.
- SENSITIVITY: 93 Db
Introduction
The 500 watt peak power of Pyle’s 10″ marine subwoofer with a 4 ohm impedance is available. It’s a terrific addition to your marine music audio system because it allows you to crank out some powerful low frequency bass volume to up the party feel. Your marine stereo sound system would benefit greatly from adding the Hydra subwoofer. Don’t deprive your boat of the very finest sound you can get because no sound system is complete without the ideal subwoofer for balancing bass. The marine grade waterproof plastic case structure of the professional compact loud speaker system makes it safe to be installed and operated in locations where mild water splashes occur, such as in marine vehicles.
A 10″ high-quality polypropylene cone is included on the white outdoor bass speaker. In order to obtain a frequency response of 25 Hz to 2.5 kHz, the 50 oz magnetic structure and 1.5″ high temperature voice coil boom with power were used. The boat subwoofer can be mounted within a box or cooler, under or in front of the compartment or helm, behind the helm seat, or any other suitable location. The subwoofer has a 10.6″ overall diameter and a 4.60″ mounting depth. Subwoofer capable of handling 500 watts of power at 4 ohms. Cone woofer made of weather-resistant polypropylene with a rubber rim. molded marine grille integrated into the design for additional protection. suitable for sealed or vented enclosures, 4.6-inch mounting depth. 25Hz to 2.5kHz range of frequencies.
WHAT’S IN THE BOX
- 2x marine speakers
- 2x speaker foam
DIMENSIONS
INSTALLATION/PLACEMENT
The boat subwoofer can be mounted within a box or cooler, under or in front of the compartment or helm, behind the helm seat, or any other suitable location. 10.6″ is the overall diameter and 4.60″ is the mounting depth of the subwoofer.
WATER-RESISTANT
The marine grade waterproof plastic case structure of the professional compact loud speaker system makes it safe to be installed and operated in locations where mild water splashes occur, such as in marine vehicles.
FAQs
Anybody know whether the grill can be taken off?****
I have speakers like that, and the grill is removable.
what size hole should I drill for these? I’m just making sure it fits because I already have a hole in my boat.****
Any 10 inch hole will do. This ought to fit if you already own a 10″ speaker.
This sub can it get muddy****
My equipment hasn’t actually been covered in mud, but it has been repeatedly submerged in water. I put one in the speaker cooler I use when river rafting, and I haven’t run into any problems. Just be sure to cover it with a grill for safety.
Please give me the box measurements for this subwoofer both with and without vents. It was missing from the instructions.****
Without ports, it should be one foot wide by one foot high by one foot deep. By adding additional polyfill, you’ll also get a bass sound that is more tightly focused.
What cutout diameter is required?****
In response, I applied the installation template. Utilizing a router, the holes were cut into the 3/8 fiberglass (fine bit edge)
Can I connect this without using an external amplifier directly to the Pyle Radio Plmr38b sub out connections?****
It has a two-wire connector that is black and red, I suppose.
What is the rms power of these speakers?****
Two speakers
Why can’t I return this item? Never has the packaging been opened!****
Because you usually get what you pay for. Years ago, I used mine in a hipper stereo. As long as you have a nice amp for it, it still sounds good.
How far do these go?****
They deliver strong bass. They don’t have twelves or anything, but they work well.
Are the two speakers pushing 500 watts or one speaker?****
It is 500 watts for two speakers, not one, if there are two speakers. Visit our website, pyleaudio.com, to view the unit’s further specifications. For further information, enter the model number PLMRW10 in the search box.
four speakers, two pairs****
Yes, two make a pair.
For each or simply one, 600 watts?****
Each one is 600 watts.
What size is the cut-out?****
My guess is that it is on the box. However, I can’t recall.
Does anyone know this sub’s RMS rating?****
It should be 250 watts, but it isn’t. It’s probably closer to 150w RMS, and even 175w would be a significant MAYBE. I have this in my river cooler, which is amazing, I’ll admit. excellent for that. The pricing is also difficult to beat. However, if you intend to use this on a boat, I recommend prioritizing quality over number.
Do you guys think this will function on a 400 watt amp jet ski?****
I’m not sure, in response. It’s in our 22-foot pontoon boat.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>